CJ7 Oil Guage won't work - HELP
Guest
Posts: n/a
CJ7 Oil Guage won't work - HELP
My '86 Jeep CJ7 with a 258 CI and 4 Spd manual runs fine, sounds good
but it gives me a fit because I cannot seem to get the oil guage to
work. I have replaced both the sending unit and the guage and get no
reading at all with the purple hooked up to the middle terminal, red
to the positive and black to the negative. If I momentarilay swap the
red and black, I get the needle to peg at full reading so I have
current there. What could it be and what is the fix?? Anyone??
Thanks, in advance for any ideas you may have. Dan
but it gives me a fit because I cannot seem to get the oil guage to
work. I have replaced both the sending unit and the guage and get no
reading at all with the purple hooked up to the middle terminal, red
to the positive and black to the negative. If I momentarilay swap the
red and black, I get the needle to peg at full reading so I have
current there. What could it be and what is the fix?? Anyone??
Thanks, in advance for any ideas you may have. Dan
Guest
Posts: n/a
Re: CJ7 Oil Guage won't work - HELP
http://www.monsterslayer.com/jeep/Gauges.htm
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Dan Grulke wrote:
>
> My '86 Jeep CJ7 with a 258 CI and 4 Spd manual runs fine, sounds good
> but it gives me a fit because I cannot seem to get the oil guage to
> work. I have replaced both the sending unit and the guage and get no
> reading at all with the purple hooked up to the middle terminal, red
> to the positive and black to the negative. If I momentarilay swap the
> red and black, I get the needle to peg at full reading so I have
> current there. What could it be and what is the fix?? Anyone??
> Thanks, in advance for any ideas you may have. Dan
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Dan Grulke wrote:
>
> My '86 Jeep CJ7 with a 258 CI and 4 Spd manual runs fine, sounds good
> but it gives me a fit because I cannot seem to get the oil guage to
> work. I have replaced both the sending unit and the guage and get no
> reading at all with the purple hooked up to the middle terminal, red
> to the positive and black to the negative. If I momentarilay swap the
> red and black, I get the needle to peg at full reading so I have
> current there. What could it be and what is the fix?? Anyone??
> Thanks, in advance for any ideas you may have. Dan
Guest
Posts: n/a
Re: CJ7 Oil Guage won't work - HELP
http://www.monsterslayer.com/jeep/Gauges.htm
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Dan Grulke wrote:
>
> My '86 Jeep CJ7 with a 258 CI and 4 Spd manual runs fine, sounds good
> but it gives me a fit because I cannot seem to get the oil guage to
> work. I have replaced both the sending unit and the guage and get no
> reading at all with the purple hooked up to the middle terminal, red
> to the positive and black to the negative. If I momentarilay swap the
> red and black, I get the needle to peg at full reading so I have
> current there. What could it be and what is the fix?? Anyone??
> Thanks, in advance for any ideas you may have. Dan
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Dan Grulke wrote:
>
> My '86 Jeep CJ7 with a 258 CI and 4 Spd manual runs fine, sounds good
> but it gives me a fit because I cannot seem to get the oil guage to
> work. I have replaced both the sending unit and the guage and get no
> reading at all with the purple hooked up to the middle terminal, red
> to the positive and black to the negative. If I momentarilay swap the
> red and black, I get the needle to peg at full reading so I have
> current there. What could it be and what is the fix?? Anyone??
> Thanks, in advance for any ideas you may have. Dan
Guest
Posts: n/a
Re: CJ7 Oil Guage won't work - HELP
http://www.monsterslayer.com/jeep/Gauges.htm
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Dan Grulke wrote:
>
> My '86 Jeep CJ7 with a 258 CI and 4 Spd manual runs fine, sounds good
> but it gives me a fit because I cannot seem to get the oil guage to
> work. I have replaced both the sending unit and the guage and get no
> reading at all with the purple hooked up to the middle terminal, red
> to the positive and black to the negative. If I momentarilay swap the
> red and black, I get the needle to peg at full reading so I have
> current there. What could it be and what is the fix?? Anyone??
> Thanks, in advance for any ideas you may have. Dan
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Dan Grulke wrote:
>
> My '86 Jeep CJ7 with a 258 CI and 4 Spd manual runs fine, sounds good
> but it gives me a fit because I cannot seem to get the oil guage to
> work. I have replaced both the sending unit and the guage and get no
> reading at all with the purple hooked up to the middle terminal, red
> to the positive and black to the negative. If I momentarilay swap the
> red and black, I get the needle to peg at full reading so I have
> current there. What could it be and what is the fix?? Anyone??
> Thanks, in advance for any ideas you may have. Dan
Guest
Posts: n/a
Re: CJ7 Oil Guage won't work - HELP
http://www.monsterslayer.com/jeep/Gauges.htm
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Dan Grulke wrote:
>
> My '86 Jeep CJ7 with a 258 CI and 4 Spd manual runs fine, sounds good
> but it gives me a fit because I cannot seem to get the oil guage to
> work. I have replaced both the sending unit and the guage and get no
> reading at all with the purple hooked up to the middle terminal, red
> to the positive and black to the negative. If I momentarilay swap the
> red and black, I get the needle to peg at full reading so I have
> current there. What could it be and what is the fix?? Anyone??
> Thanks, in advance for any ideas you may have. Dan
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Dan Grulke wrote:
>
> My '86 Jeep CJ7 with a 258 CI and 4 Spd manual runs fine, sounds good
> but it gives me a fit because I cannot seem to get the oil guage to
> work. I have replaced both the sending unit and the guage and get no
> reading at all with the purple hooked up to the middle terminal, red
> to the positive and black to the negative. If I momentarilay swap the
> red and black, I get the needle to peg at full reading so I have
> current there. What could it be and what is the fix?? Anyone??
> Thanks, in advance for any ideas you may have. Dan
Guest
Posts: n/a
Re: CJ7 Oil Guage won't work - HELP
Umm, purple wire?
Are you sure you have the solid purple one and not the one with a
stripe? The purple one with the stripe is from the back of the engine
head and is the temp sender.
Did you by chance insulate the sender with teflon tape so it has no
ground?
Is the ground from the engine head to the firewall hooked up?
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Dan Grulke wrote:
>
> My '86 Jeep CJ7 with a 258 CI and 4 Spd manual runs fine, sounds good
> but it gives me a fit because I cannot seem to get the oil guage to
> work. I have replaced both the sending unit and the guage and get no
> reading at all with the purple hooked up to the middle terminal, red
> to the positive and black to the negative. If I momentarilay swap the
> red and black, I get the needle to peg at full reading so I have
> current there. What could it be and what is the fix?? Anyone??
> Thanks, in advance for any ideas you may have. Dan
Are you sure you have the solid purple one and not the one with a
stripe? The purple one with the stripe is from the back of the engine
head and is the temp sender.
Did you by chance insulate the sender with teflon tape so it has no
ground?
Is the ground from the engine head to the firewall hooked up?
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Dan Grulke wrote:
>
> My '86 Jeep CJ7 with a 258 CI and 4 Spd manual runs fine, sounds good
> but it gives me a fit because I cannot seem to get the oil guage to
> work. I have replaced both the sending unit and the guage and get no
> reading at all with the purple hooked up to the middle terminal, red
> to the positive and black to the negative. If I momentarilay swap the
> red and black, I get the needle to peg at full reading so I have
> current there. What could it be and what is the fix?? Anyone??
> Thanks, in advance for any ideas you may have. Dan
Guest
Posts: n/a
Re: CJ7 Oil Guage won't work - HELP
Umm, purple wire?
Are you sure you have the solid purple one and not the one with a
stripe? The purple one with the stripe is from the back of the engine
head and is the temp sender.
Did you by chance insulate the sender with teflon tape so it has no
ground?
Is the ground from the engine head to the firewall hooked up?
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Dan Grulke wrote:
>
> My '86 Jeep CJ7 with a 258 CI and 4 Spd manual runs fine, sounds good
> but it gives me a fit because I cannot seem to get the oil guage to
> work. I have replaced both the sending unit and the guage and get no
> reading at all with the purple hooked up to the middle terminal, red
> to the positive and black to the negative. If I momentarilay swap the
> red and black, I get the needle to peg at full reading so I have
> current there. What could it be and what is the fix?? Anyone??
> Thanks, in advance for any ideas you may have. Dan
Are you sure you have the solid purple one and not the one with a
stripe? The purple one with the stripe is from the back of the engine
head and is the temp sender.
Did you by chance insulate the sender with teflon tape so it has no
ground?
Is the ground from the engine head to the firewall hooked up?
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Dan Grulke wrote:
>
> My '86 Jeep CJ7 with a 258 CI and 4 Spd manual runs fine, sounds good
> but it gives me a fit because I cannot seem to get the oil guage to
> work. I have replaced both the sending unit and the guage and get no
> reading at all with the purple hooked up to the middle terminal, red
> to the positive and black to the negative. If I momentarilay swap the
> red and black, I get the needle to peg at full reading so I have
> current there. What could it be and what is the fix?? Anyone??
> Thanks, in advance for any ideas you may have. Dan
Guest
Posts: n/a
Re: CJ7 Oil Guage won't work - HELP
Umm, purple wire?
Are you sure you have the solid purple one and not the one with a
stripe? The purple one with the stripe is from the back of the engine
head and is the temp sender.
Did you by chance insulate the sender with teflon tape so it has no
ground?
Is the ground from the engine head to the firewall hooked up?
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Dan Grulke wrote:
>
> My '86 Jeep CJ7 with a 258 CI and 4 Spd manual runs fine, sounds good
> but it gives me a fit because I cannot seem to get the oil guage to
> work. I have replaced both the sending unit and the guage and get no
> reading at all with the purple hooked up to the middle terminal, red
> to the positive and black to the negative. If I momentarilay swap the
> red and black, I get the needle to peg at full reading so I have
> current there. What could it be and what is the fix?? Anyone??
> Thanks, in advance for any ideas you may have. Dan
Are you sure you have the solid purple one and not the one with a
stripe? The purple one with the stripe is from the back of the engine
head and is the temp sender.
Did you by chance insulate the sender with teflon tape so it has no
ground?
Is the ground from the engine head to the firewall hooked up?
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Dan Grulke wrote:
>
> My '86 Jeep CJ7 with a 258 CI and 4 Spd manual runs fine, sounds good
> but it gives me a fit because I cannot seem to get the oil guage to
> work. I have replaced both the sending unit and the guage and get no
> reading at all with the purple hooked up to the middle terminal, red
> to the positive and black to the negative. If I momentarilay swap the
> red and black, I get the needle to peg at full reading so I have
> current there. What could it be and what is the fix?? Anyone??
> Thanks, in advance for any ideas you may have. Dan
Guest
Posts: n/a
Re: CJ7 Oil Guage won't work - HELP
Umm, purple wire?
Are you sure you have the solid purple one and not the one with a
stripe? The purple one with the stripe is from the back of the engine
head and is the temp sender.
Did you by chance insulate the sender with teflon tape so it has no
ground?
Is the ground from the engine head to the firewall hooked up?
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Dan Grulke wrote:
>
> My '86 Jeep CJ7 with a 258 CI and 4 Spd manual runs fine, sounds good
> but it gives me a fit because I cannot seem to get the oil guage to
> work. I have replaced both the sending unit and the guage and get no
> reading at all with the purple hooked up to the middle terminal, red
> to the positive and black to the negative. If I momentarilay swap the
> red and black, I get the needle to peg at full reading so I have
> current there. What could it be and what is the fix?? Anyone??
> Thanks, in advance for any ideas you may have. Dan
Are you sure you have the solid purple one and not the one with a
stripe? The purple one with the stripe is from the back of the engine
head and is the temp sender.
Did you by chance insulate the sender with teflon tape so it has no
ground?
Is the ground from the engine head to the firewall hooked up?
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Dan Grulke wrote:
>
> My '86 Jeep CJ7 with a 258 CI and 4 Spd manual runs fine, sounds good
> but it gives me a fit because I cannot seem to get the oil guage to
> work. I have replaced both the sending unit and the guage and get no
> reading at all with the purple hooked up to the middle terminal, red
> to the positive and black to the negative. If I momentarilay swap the
> red and black, I get the needle to peg at full reading so I have
> current there. What could it be and what is the fix?? Anyone??
> Thanks, in advance for any ideas you may have. Dan
Thread
Thread Starter
Forum
Replies
Last Post
RG
Jeep Mailing List
28
Aug 24, 2004 10:08 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
