Changing 1988 Comanche Starter
03-12-2006, 11:07 PM
#21
Guest
Posts: n/a
Re: Changing 1988 Comanche Starter
Reaching the top bolt is a pain and getting it back in can take some
fiddling but it's pretty straight forward. I take the positive cable
and solenoid wiring off after I drop it down where I can reach things
then hook it back up before bolting it in.
Sun, 12 Mar 2006 23:46:18 UTC "Goshi Key" <kgoshi@***.net> wrote:
> I think I need to replace the starter on my 1988 Jeep Comanche (L6 4.0) as
> the engine won't turn over while the battery tests fine. I've managed to
> figure out its location and can get under the vehicle to get to it. Just
> want to know on a 1 to 10 difficulty scale of do it yourself repair work,
> how this particualr job rates.
>
>
--
Will Honea
fiddling but it's pretty straight forward. I take the positive cable
and solenoid wiring off after I drop it down where I can reach things
then hook it back up before bolting it in.
Sun, 12 Mar 2006 23:46:18 UTC "Goshi Key" <kgoshi@***.net> wrote:
> I think I need to replace the starter on my 1988 Jeep Comanche (L6 4.0) as
> the engine won't turn over while the battery tests fine. I've managed to
> figure out its location and can get under the vehicle to get to it. Just
> want to know on a 1 to 10 difficulty scale of do it yourself repair work,
> how this particualr job rates.
>
>
--
Will Honea
03-13-2006, 09:16 AM
#22
Guest
Posts: n/a
Re: Changing 1988 Comanche Starter
Goshi Key wrote:
> I think I need to replace the starter on my 1988 Jeep Comanche (L6 4.0) as
> the engine won't turn over while the battery tests fine. I've managed to
> figure out its location and can get under the vehicle to get to it. Just
> want to know on a 1 to 10 difficulty scale of do it yourself repair work,
> how this particualr job rates.
ECHO: Wot the others said about cleaning the cables -- both ends --
first. Grounding issues are a very big deal with Jeeps.
Back a couple of years ago when I swapped out my starter on my `89
Cherokee I6 4.0L I found that I needed both sets of wrenches. Things
that thread into the engine are metric, things that thread into the
starter are SAE (or t'other way around). Mining a thread from 2003 I
see that the lower bolt is SAE 9/16" and is easily approached from the
front, the upper from the rear -- and it is in a really tight place. I
broke the bolt loose with a box wrench and then use a 3/8" "wobble"
extension (with a metric socket) to get the ratchet head into a place
where I could swing it.
And I also made this observation:
There's only two wires, a control lead and the battery cable. When you
put the new starter in, pay particular attention to which bolt the
battery cable went to. Laying on your back in the driveway it will be
easy to confuse the two and attach it to the wrong bolt. This will be
Very Bad. You'll know by the huge spark when you try to put the battery
cable back on the battery post if you've got it wrong.
Let us know how you make out.
> I think I need to replace the starter on my 1988 Jeep Comanche (L6 4.0) as
> the engine won't turn over while the battery tests fine. I've managed to
> figure out its location and can get under the vehicle to get to it. Just
> want to know on a 1 to 10 difficulty scale of do it yourself repair work,
> how this particualr job rates.
ECHO: Wot the others said about cleaning the cables -- both ends --
first. Grounding issues are a very big deal with Jeeps.
Back a couple of years ago when I swapped out my starter on my `89
Cherokee I6 4.0L I found that I needed both sets of wrenches. Things
that thread into the engine are metric, things that thread into the
starter are SAE (or t'other way around). Mining a thread from 2003 I
see that the lower bolt is SAE 9/16" and is easily approached from the
front, the upper from the rear -- and it is in a really tight place. I
broke the bolt loose with a box wrench and then use a 3/8" "wobble"
extension (with a metric socket) to get the ratchet head into a place
where I could swing it.
And I also made this observation:
There's only two wires, a control lead and the battery cable. When you
put the new starter in, pay particular attention to which bolt the
battery cable went to. Laying on your back in the driveway it will be
easy to confuse the two and attach it to the wrong bolt. This will be
Very Bad. You'll know by the huge spark when you try to put the battery
cable back on the battery post if you've got it wrong.
Let us know how you make out.
03-13-2006, 09:16 AM
#23
Guest
Posts: n/a
Re: Changing 1988 Comanche Starter
Goshi Key wrote:
> I think I need to replace the starter on my 1988 Jeep Comanche (L6 4.0) as
> the engine won't turn over while the battery tests fine. I've managed to
> figure out its location and can get under the vehicle to get to it. Just
> want to know on a 1 to 10 difficulty scale of do it yourself repair work,
> how this particualr job rates.
ECHO: Wot the others said about cleaning the cables -- both ends --
first. Grounding issues are a very big deal with Jeeps.
Back a couple of years ago when I swapped out my starter on my `89
Cherokee I6 4.0L I found that I needed both sets of wrenches. Things
that thread into the engine are metric, things that thread into the
starter are SAE (or t'other way around). Mining a thread from 2003 I
see that the lower bolt is SAE 9/16" and is easily approached from the
front, the upper from the rear -- and it is in a really tight place. I
broke the bolt loose with a box wrench and then use a 3/8" "wobble"
extension (with a metric socket) to get the ratchet head into a place
where I could swing it.
And I also made this observation:
There's only two wires, a control lead and the battery cable. When you
put the new starter in, pay particular attention to which bolt the
battery cable went to. Laying on your back in the driveway it will be
easy to confuse the two and attach it to the wrong bolt. This will be
Very Bad. You'll know by the huge spark when you try to put the battery
cable back on the battery post if you've got it wrong.
Let us know how you make out.
> I think I need to replace the starter on my 1988 Jeep Comanche (L6 4.0) as
> the engine won't turn over while the battery tests fine. I've managed to
> figure out its location and can get under the vehicle to get to it. Just
> want to know on a 1 to 10 difficulty scale of do it yourself repair work,
> how this particualr job rates.
ECHO: Wot the others said about cleaning the cables -- both ends --
first. Grounding issues are a very big deal with Jeeps.
Back a couple of years ago when I swapped out my starter on my `89
Cherokee I6 4.0L I found that I needed both sets of wrenches. Things
that thread into the engine are metric, things that thread into the
starter are SAE (or t'other way around). Mining a thread from 2003 I
see that the lower bolt is SAE 9/16" and is easily approached from the
front, the upper from the rear -- and it is in a really tight place. I
broke the bolt loose with a box wrench and then use a 3/8" "wobble"
extension (with a metric socket) to get the ratchet head into a place
where I could swing it.
And I also made this observation:
There's only two wires, a control lead and the battery cable. When you
put the new starter in, pay particular attention to which bolt the
battery cable went to. Laying on your back in the driveway it will be
easy to confuse the two and attach it to the wrong bolt. This will be
Very Bad. You'll know by the huge spark when you try to put the battery
cable back on the battery post if you've got it wrong.
Let us know how you make out.
03-13-2006, 09:16 AM
#24
Guest
Posts: n/a
Re: Changing 1988 Comanche Starter
Goshi Key wrote:
> I think I need to replace the starter on my 1988 Jeep Comanche (L6 4.0) as
> the engine won't turn over while the battery tests fine. I've managed to
> figure out its location and can get under the vehicle to get to it. Just
> want to know on a 1 to 10 difficulty scale of do it yourself repair work,
> how this particualr job rates.
ECHO: Wot the others said about cleaning the cables -- both ends --
first. Grounding issues are a very big deal with Jeeps.
Back a couple of years ago when I swapped out my starter on my `89
Cherokee I6 4.0L I found that I needed both sets of wrenches. Things
that thread into the engine are metric, things that thread into the
starter are SAE (or t'other way around). Mining a thread from 2003 I
see that the lower bolt is SAE 9/16" and is easily approached from the
front, the upper from the rear -- and it is in a really tight place. I
broke the bolt loose with a box wrench and then use a 3/8" "wobble"
extension (with a metric socket) to get the ratchet head into a place
where I could swing it.
And I also made this observation:
There's only two wires, a control lead and the battery cable. When you
put the new starter in, pay particular attention to which bolt the
battery cable went to. Laying on your back in the driveway it will be
easy to confuse the two and attach it to the wrong bolt. This will be
Very Bad. You'll know by the huge spark when you try to put the battery
cable back on the battery post if you've got it wrong.
Let us know how you make out.
> I think I need to replace the starter on my 1988 Jeep Comanche (L6 4.0) as
> the engine won't turn over while the battery tests fine. I've managed to
> figure out its location and can get under the vehicle to get to it. Just
> want to know on a 1 to 10 difficulty scale of do it yourself repair work,
> how this particualr job rates.
ECHO: Wot the others said about cleaning the cables -- both ends --
first. Grounding issues are a very big deal with Jeeps.
Back a couple of years ago when I swapped out my starter on my `89
Cherokee I6 4.0L I found that I needed both sets of wrenches. Things
that thread into the engine are metric, things that thread into the
starter are SAE (or t'other way around). Mining a thread from 2003 I
see that the lower bolt is SAE 9/16" and is easily approached from the
front, the upper from the rear -- and it is in a really tight place. I
broke the bolt loose with a box wrench and then use a 3/8" "wobble"
extension (with a metric socket) to get the ratchet head into a place
where I could swing it.
And I also made this observation:
There's only two wires, a control lead and the battery cable. When you
put the new starter in, pay particular attention to which bolt the
battery cable went to. Laying on your back in the driveway it will be
easy to confuse the two and attach it to the wrong bolt. This will be
Very Bad. You'll know by the huge spark when you try to put the battery
cable back on the battery post if you've got it wrong.
Let us know how you make out.
03-13-2006, 09:16 AM
#25
Guest
Posts: n/a
Re: Changing 1988 Comanche Starter
Goshi Key wrote:
> I think I need to replace the starter on my 1988 Jeep Comanche (L6 4.0) as
> the engine won't turn over while the battery tests fine. I've managed to
> figure out its location and can get under the vehicle to get to it. Just
> want to know on a 1 to 10 difficulty scale of do it yourself repair work,
> how this particualr job rates.
ECHO: Wot the others said about cleaning the cables -- both ends --
first. Grounding issues are a very big deal with Jeeps.
Back a couple of years ago when I swapped out my starter on my `89
Cherokee I6 4.0L I found that I needed both sets of wrenches. Things
that thread into the engine are metric, things that thread into the
starter are SAE (or t'other way around). Mining a thread from 2003 I
see that the lower bolt is SAE 9/16" and is easily approached from the
front, the upper from the rear -- and it is in a really tight place. I
broke the bolt loose with a box wrench and then use a 3/8" "wobble"
extension (with a metric socket) to get the ratchet head into a place
where I could swing it.
And I also made this observation:
There's only two wires, a control lead and the battery cable. When you
put the new starter in, pay particular attention to which bolt the
battery cable went to. Laying on your back in the driveway it will be
easy to confuse the two and attach it to the wrong bolt. This will be
Very Bad. You'll know by the huge spark when you try to put the battery
cable back on the battery post if you've got it wrong.
Let us know how you make out.
> I think I need to replace the starter on my 1988 Jeep Comanche (L6 4.0) as
> the engine won't turn over while the battery tests fine. I've managed to
> figure out its location and can get under the vehicle to get to it. Just
> want to know on a 1 to 10 difficulty scale of do it yourself repair work,
> how this particualr job rates.
ECHO: Wot the others said about cleaning the cables -- both ends --
first. Grounding issues are a very big deal with Jeeps.
Back a couple of years ago when I swapped out my starter on my `89
Cherokee I6 4.0L I found that I needed both sets of wrenches. Things
that thread into the engine are metric, things that thread into the
starter are SAE (or t'other way around). Mining a thread from 2003 I
see that the lower bolt is SAE 9/16" and is easily approached from the
front, the upper from the rear -- and it is in a really tight place. I
broke the bolt loose with a box wrench and then use a 3/8" "wobble"
extension (with a metric socket) to get the ratchet head into a place
where I could swing it.
And I also made this observation:
There's only two wires, a control lead and the battery cable. When you
put the new starter in, pay particular attention to which bolt the
battery cable went to. Laying on your back in the driveway it will be
easy to confuse the two and attach it to the wrong bolt. This will be
Very Bad. You'll know by the huge spark when you try to put the battery
cable back on the battery post if you've got it wrong.
Let us know how you make out.
03-13-2006, 07:19 PM
#26
Guest
Posts: n/a
Re: Changing 1988 Comanche Starter
Hi Goshi
The advice you were given was excellent. Always disconnect the battery
before attempting to change the starter, and double check the grounds.
However, you may have a problem with the ignition switch or solenoid. I
had this problem with my 87 Cherokee 4.0 last Christmas. The switch
failed and I jump started from the solenoid (Ford type). I added a
heavy duty momentary toggle switch in the dash directly to the
solenoid. Then when the weather was nicer, I changed the ignition
switch but left the starter switch in the dash.
I would not want to change the starter and still have the same problem.
Merrill
Goshi Key wrote:
> I think I need to replace the starter on my 1988 Jeep Comanche (L6 4.0) as
> the engine won't turn over while the battery tests fine. I've managed to
> figure out its location and can get under the vehicle to get to it. Just
> want to know on a 1 to 10 difficulty scale of do it yourself repair work,
> how this particualr job rates.
The advice you were given was excellent. Always disconnect the battery
before attempting to change the starter, and double check the grounds.
However, you may have a problem with the ignition switch or solenoid. I
had this problem with my 87 Cherokee 4.0 last Christmas. The switch
failed and I jump started from the solenoid (Ford type). I added a
heavy duty momentary toggle switch in the dash directly to the
solenoid. Then when the weather was nicer, I changed the ignition
switch but left the starter switch in the dash.
I would not want to change the starter and still have the same problem.
Merrill
Goshi Key wrote:
> I think I need to replace the starter on my 1988 Jeep Comanche (L6 4.0) as
> the engine won't turn over while the battery tests fine. I've managed to
> figure out its location and can get under the vehicle to get to it. Just
> want to know on a 1 to 10 difficulty scale of do it yourself repair work,
> how this particualr job rates.
03-13-2006, 07:19 PM
#27
Guest
Posts: n/a
Re: Changing 1988 Comanche Starter
Hi Goshi
The advice you were given was excellent. Always disconnect the battery
before attempting to change the starter, and double check the grounds.
However, you may have a problem with the ignition switch or solenoid. I
had this problem with my 87 Cherokee 4.0 last Christmas. The switch
failed and I jump started from the solenoid (Ford type). I added a
heavy duty momentary toggle switch in the dash directly to the
solenoid. Then when the weather was nicer, I changed the ignition
switch but left the starter switch in the dash.
I would not want to change the starter and still have the same problem.
Merrill
Goshi Key wrote:
> I think I need to replace the starter on my 1988 Jeep Comanche (L6 4.0) as
> the engine won't turn over while the battery tests fine. I've managed to
> figure out its location and can get under the vehicle to get to it. Just
> want to know on a 1 to 10 difficulty scale of do it yourself repair work,
> how this particualr job rates.
The advice you were given was excellent. Always disconnect the battery
before attempting to change the starter, and double check the grounds.
However, you may have a problem with the ignition switch or solenoid. I
had this problem with my 87 Cherokee 4.0 last Christmas. The switch
failed and I jump started from the solenoid (Ford type). I added a
heavy duty momentary toggle switch in the dash directly to the
solenoid. Then when the weather was nicer, I changed the ignition
switch but left the starter switch in the dash.
I would not want to change the starter and still have the same problem.
Merrill
Goshi Key wrote:
> I think I need to replace the starter on my 1988 Jeep Comanche (L6 4.0) as
> the engine won't turn over while the battery tests fine. I've managed to
> figure out its location and can get under the vehicle to get to it. Just
> want to know on a 1 to 10 difficulty scale of do it yourself repair work,
> how this particualr job rates.
03-13-2006, 07:19 PM
#28
Guest
Posts: n/a
Re: Changing 1988 Comanche Starter
Hi Goshi
The advice you were given was excellent. Always disconnect the battery
before attempting to change the starter, and double check the grounds.
However, you may have a problem with the ignition switch or solenoid. I
had this problem with my 87 Cherokee 4.0 last Christmas. The switch
failed and I jump started from the solenoid (Ford type). I added a
heavy duty momentary toggle switch in the dash directly to the
solenoid. Then when the weather was nicer, I changed the ignition
switch but left the starter switch in the dash.
I would not want to change the starter and still have the same problem.
Merrill
Goshi Key wrote:
> I think I need to replace the starter on my 1988 Jeep Comanche (L6 4.0) as
> the engine won't turn over while the battery tests fine. I've managed to
> figure out its location and can get under the vehicle to get to it. Just
> want to know on a 1 to 10 difficulty scale of do it yourself repair work,
> how this particualr job rates.
The advice you were given was excellent. Always disconnect the battery
before attempting to change the starter, and double check the grounds.
However, you may have a problem with the ignition switch or solenoid. I
had this problem with my 87 Cherokee 4.0 last Christmas. The switch
failed and I jump started from the solenoid (Ford type). I added a
heavy duty momentary toggle switch in the dash directly to the
solenoid. Then when the weather was nicer, I changed the ignition
switch but left the starter switch in the dash.
I would not want to change the starter and still have the same problem.
Merrill
Goshi Key wrote:
> I think I need to replace the starter on my 1988 Jeep Comanche (L6 4.0) as
> the engine won't turn over while the battery tests fine. I've managed to
> figure out its location and can get under the vehicle to get to it. Just
> want to know on a 1 to 10 difficulty scale of do it yourself repair work,
> how this particualr job rates.
03-13-2006, 07:19 PM
#29
Guest
Posts: n/a
Re: Changing 1988 Comanche Starter
Hi Goshi
The advice you were given was excellent. Always disconnect the battery
before attempting to change the starter, and double check the grounds.
However, you may have a problem with the ignition switch or solenoid. I
had this problem with my 87 Cherokee 4.0 last Christmas. The switch
failed and I jump started from the solenoid (Ford type). I added a
heavy duty momentary toggle switch in the dash directly to the
solenoid. Then when the weather was nicer, I changed the ignition
switch but left the starter switch in the dash.
I would not want to change the starter and still have the same problem.
Merrill
Goshi Key wrote:
> I think I need to replace the starter on my 1988 Jeep Comanche (L6 4.0) as
> the engine won't turn over while the battery tests fine. I've managed to
> figure out its location and can get under the vehicle to get to it. Just
> want to know on a 1 to 10 difficulty scale of do it yourself repair work,
> how this particualr job rates.
The advice you were given was excellent. Always disconnect the battery
before attempting to change the starter, and double check the grounds.
However, you may have a problem with the ignition switch or solenoid. I
had this problem with my 87 Cherokee 4.0 last Christmas. The switch
failed and I jump started from the solenoid (Ford type). I added a
heavy duty momentary toggle switch in the dash directly to the
solenoid. Then when the weather was nicer, I changed the ignition
switch but left the starter switch in the dash.
I would not want to change the starter and still have the same problem.
Merrill
Goshi Key wrote:
> I think I need to replace the starter on my 1988 Jeep Comanche (L6 4.0) as
> the engine won't turn over while the battery tests fine. I've managed to
> figure out its location and can get under the vehicle to get to it. Just
> want to know on a 1 to 10 difficulty scale of do it yourself repair work,
> how this particualr job rates.
03-14-2006, 11:49 AM
#30
Guest
Posts: n/a
Re: Changing 1988 Comanche Starter
Not too hard, but as the others mention, I would suspect wiring first.
One test is to turn on the headlights and watch then when someone tries
the starter. If the lights dim, suspect the starter, if the lights
don't dim, suspect a connection.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
Goshi Key wrote:
>
> I think I need to replace the starter on my 1988 Jeep Comanche (L6 4.0) as
> the engine won't turn over while the battery tests fine. I've managed to
> figure out its location and can get under the vehicle to get to it. Just
> want to know on a 1 to 10 difficulty scale of do it yourself repair work,
> how this particualr job rates.
One test is to turn on the headlights and watch then when someone tries
the starter. If the lights dim, suspect the starter, if the lights
don't dim, suspect a connection.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
Goshi Key wrote:
>
> I think I need to replace the starter on my 1988 Jeep Comanche (L6 4.0) as
> the engine won't turn over while the battery tests fine. I've managed to
> figure out its location and can get under the vehicle to get to it. Just
> want to know on a 1 to 10 difficulty scale of do it yourself repair work,
> how this particualr job rates.
