brake question
#11
Guest
Posts: n/a
Re: brake question
The brakes used to be fine before the tubing was replaced. Also, the
bleeding method I'm using is with a rubber tube and a container of
fluid. An assistant was helping with the pedal. The way is was
behaving is that fluid with no air comes out and then suddenly it
"spits" a two inch section of air in the clear rubber tube, then a few
small bubbles. With the next pedal press, the same thing happens again
and so on. I'm pretty sure the problem is between the rubber
hose/metal tube junction and the right rear wheel because no air comes
out of the left rear.
Thanks,
nrs
bleeding method I'm using is with a rubber tube and a container of
fluid. An assistant was helping with the pedal. The way is was
behaving is that fluid with no air comes out and then suddenly it
"spits" a two inch section of air in the clear rubber tube, then a few
small bubbles. With the next pedal press, the same thing happens again
and so on. I'm pretty sure the problem is between the rubber
hose/metal tube junction and the right rear wheel because no air comes
out of the left rear.
Thanks,
nrs
#12
Guest
Posts: n/a
Re: brake question
The brakes used to be fine before the tubing was replaced. Also, the
bleeding method I'm using is with a rubber tube and a container of
fluid. An assistant was helping with the pedal. The way is was
behaving is that fluid with no air comes out and then suddenly it
"spits" a two inch section of air in the clear rubber tube, then a few
small bubbles. With the next pedal press, the same thing happens again
and so on. I'm pretty sure the problem is between the rubber
hose/metal tube junction and the right rear wheel because no air comes
out of the left rear.
Thanks,
nrs
bleeding method I'm using is with a rubber tube and a container of
fluid. An assistant was helping with the pedal. The way is was
behaving is that fluid with no air comes out and then suddenly it
"spits" a two inch section of air in the clear rubber tube, then a few
small bubbles. With the next pedal press, the same thing happens again
and so on. I'm pretty sure the problem is between the rubber
hose/metal tube junction and the right rear wheel because no air comes
out of the left rear.
Thanks,
nrs
#13
Guest
Posts: n/a
Re: brake question
The brakes used to be fine before the tubing was replaced. Also, the
bleeding method I'm using is with a rubber tube and a container of
fluid. An assistant was helping with the pedal. The way is was
behaving is that fluid with no air comes out and then suddenly it
"spits" a two inch section of air in the clear rubber tube, then a few
small bubbles. With the next pedal press, the same thing happens again
and so on. I'm pretty sure the problem is between the rubber
hose/metal tube junction and the right rear wheel because no air comes
out of the left rear.
Thanks,
nrs
bleeding method I'm using is with a rubber tube and a container of
fluid. An assistant was helping with the pedal. The way is was
behaving is that fluid with no air comes out and then suddenly it
"spits" a two inch section of air in the clear rubber tube, then a few
small bubbles. With the next pedal press, the same thing happens again
and so on. I'm pretty sure the problem is between the rubber
hose/metal tube junction and the right rear wheel because no air comes
out of the left rear.
Thanks,
nrs
#14
Guest
Posts: n/a
Re: brake question
Are you closing the bleed nipple between pedal pumps?
Sometimes the air can get sucked back in past the bleeder threads if it
is left open between pumps.
Sometimes letting it gravity bleed works too.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
nrs wrote:
>
> The brakes used to be fine before the tubing was replaced. Also, the
> bleeding method I'm using is with a rubber tube and a container of
> fluid. An assistant was helping with the pedal. The way is was
> behaving is that fluid with no air comes out and then suddenly it
> "spits" a two inch section of air in the clear rubber tube, then a few
> small bubbles. With the next pedal press, the same thing happens again
> and so on. I'm pretty sure the problem is between the rubber
> hose/metal tube junction and the right rear wheel because no air comes
> out of the left rear.
>
> Thanks,
> nrs
Sometimes the air can get sucked back in past the bleeder threads if it
is left open between pumps.
Sometimes letting it gravity bleed works too.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
nrs wrote:
>
> The brakes used to be fine before the tubing was replaced. Also, the
> bleeding method I'm using is with a rubber tube and a container of
> fluid. An assistant was helping with the pedal. The way is was
> behaving is that fluid with no air comes out and then suddenly it
> "spits" a two inch section of air in the clear rubber tube, then a few
> small bubbles. With the next pedal press, the same thing happens again
> and so on. I'm pretty sure the problem is between the rubber
> hose/metal tube junction and the right rear wheel because no air comes
> out of the left rear.
>
> Thanks,
> nrs
#15
Guest
Posts: n/a
Re: brake question
Are you closing the bleed nipple between pedal pumps?
Sometimes the air can get sucked back in past the bleeder threads if it
is left open between pumps.
Sometimes letting it gravity bleed works too.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
nrs wrote:
>
> The brakes used to be fine before the tubing was replaced. Also, the
> bleeding method I'm using is with a rubber tube and a container of
> fluid. An assistant was helping with the pedal. The way is was
> behaving is that fluid with no air comes out and then suddenly it
> "spits" a two inch section of air in the clear rubber tube, then a few
> small bubbles. With the next pedal press, the same thing happens again
> and so on. I'm pretty sure the problem is between the rubber
> hose/metal tube junction and the right rear wheel because no air comes
> out of the left rear.
>
> Thanks,
> nrs
Sometimes the air can get sucked back in past the bleeder threads if it
is left open between pumps.
Sometimes letting it gravity bleed works too.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
nrs wrote:
>
> The brakes used to be fine before the tubing was replaced. Also, the
> bleeding method I'm using is with a rubber tube and a container of
> fluid. An assistant was helping with the pedal. The way is was
> behaving is that fluid with no air comes out and then suddenly it
> "spits" a two inch section of air in the clear rubber tube, then a few
> small bubbles. With the next pedal press, the same thing happens again
> and so on. I'm pretty sure the problem is between the rubber
> hose/metal tube junction and the right rear wheel because no air comes
> out of the left rear.
>
> Thanks,
> nrs
#16
Guest
Posts: n/a
Re: brake question
Are you closing the bleed nipple between pedal pumps?
Sometimes the air can get sucked back in past the bleeder threads if it
is left open between pumps.
Sometimes letting it gravity bleed works too.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
nrs wrote:
>
> The brakes used to be fine before the tubing was replaced. Also, the
> bleeding method I'm using is with a rubber tube and a container of
> fluid. An assistant was helping with the pedal. The way is was
> behaving is that fluid with no air comes out and then suddenly it
> "spits" a two inch section of air in the clear rubber tube, then a few
> small bubbles. With the next pedal press, the same thing happens again
> and so on. I'm pretty sure the problem is between the rubber
> hose/metal tube junction and the right rear wheel because no air comes
> out of the left rear.
>
> Thanks,
> nrs
Sometimes the air can get sucked back in past the bleeder threads if it
is left open between pumps.
Sometimes letting it gravity bleed works too.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
nrs wrote:
>
> The brakes used to be fine before the tubing was replaced. Also, the
> bleeding method I'm using is with a rubber tube and a container of
> fluid. An assistant was helping with the pedal. The way is was
> behaving is that fluid with no air comes out and then suddenly it
> "spits" a two inch section of air in the clear rubber tube, then a few
> small bubbles. With the next pedal press, the same thing happens again
> and so on. I'm pretty sure the problem is between the rubber
> hose/metal tube junction and the right rear wheel because no air comes
> out of the left rear.
>
> Thanks,
> nrs
Thread
Thread Starter
Forum
Replies
Last Post
Charles Ervin
Jeep Mailing List
52
02-04-2007 11:01 PM
lambeth65@earthlink.net
Jeep Mailing List
3
10-31-2006 08:18 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)