amc 20 dana 44 replacement
Guest
Posts: n/a
Re: amc 20 dana 44 replacement
I'll go out and measure my AMC 20 when it gets light out, will post in an
hour or so.
"Deniz" <dhasirci@gmail.com> wrote in message
news:1175755955.763919.258190@p77g2000hsh.googlegr oups.com...
> On 5 Nisan, 06:53, "L.W. \(Bill\) ------ III" <billhug...@***.net>
> wrote:
>>
>> http://www.4xshaft.com/driveline101....com/index.html
>> God Bless America, Bill 0|||||||0
>> mailto:LW------...@aol.comhttp://www.----------.com/
>>
>> "Deniz" <dhasi...@gmail.com> wrote in message
>>
>> news:1175674679.158682.313630@d57g2000hsg.googlegr oups.com...
>>
>> > Hi guys,
>> > I'm from Turkey and i have 79 cj5. Recently i have replaced my amc 20
>> > with a dana 44. But some vibrations occured both while accelerating
>> > and decelerating probably because of the rear driveshaft.It's a bit
>> > difficult to find parts for cjs in Turkey, i need to have some parts
>> > made customly. Do i need a longer driveshaft as it looks slightly
>> > longer now the it used to be or should i try to have a cv type drive
>> > shaft custom made as i'm thinking of buying a 2 inch lift kit in the
>> > near future? With a cv drive shaft do i need transfer case lowering
>> > kit for 2 inch lift?
>> > Thank you all in advance,
>> > Deniz
>>
>> --
>> Posted via a free Usenet account fromhttp://www.teranews.com
>
> First of all thank you all guys,
> I'll first check the angles, but i was quite carefull installing the
> shaft. The d44 i bought was a second hand one and it was in a very
> good condition, unfortunately without a drive shaft. To be honest i
> hadn't measured the housings. But by the look of the mud marks and
> clean parts of the shaft i can tell that it's standing a wee bit
> longer. I'll try to find an old jeep on the road and stop it and get
> under to measure the shaft unfortunately there arent't many of those.
> The cv shaft option is gonna have to wait till i get the lift kit as i
> understand that i need to change the angles of the spring perches and
> i don't want to take the the axle off again, i wanna drive it for a
> while as i'd been working on it for quite some time, i missed the
> little beasty. I'll replace the u joints as well once i measure a D44
> drive shaft. The u joints are a couple of years old but i hadn't
> maintained them regularly.
> Thank you all again.
>
> Deniz
>
hour or so.
"Deniz" <dhasirci@gmail.com> wrote in message
news:1175755955.763919.258190@p77g2000hsh.googlegr oups.com...
> On 5 Nisan, 06:53, "L.W. \(Bill\) ------ III" <billhug...@***.net>
> wrote:
>>
>> http://www.4xshaft.com/driveline101....com/index.html
>> God Bless America, Bill 0|||||||0
>> mailto:LW------...@aol.comhttp://www.----------.com/
>>
>> "Deniz" <dhasi...@gmail.com> wrote in message
>>
>> news:1175674679.158682.313630@d57g2000hsg.googlegr oups.com...
>>
>> > Hi guys,
>> > I'm from Turkey and i have 79 cj5. Recently i have replaced my amc 20
>> > with a dana 44. But some vibrations occured both while accelerating
>> > and decelerating probably because of the rear driveshaft.It's a bit
>> > difficult to find parts for cjs in Turkey, i need to have some parts
>> > made customly. Do i need a longer driveshaft as it looks slightly
>> > longer now the it used to be or should i try to have a cv type drive
>> > shaft custom made as i'm thinking of buying a 2 inch lift kit in the
>> > near future? With a cv drive shaft do i need transfer case lowering
>> > kit for 2 inch lift?
>> > Thank you all in advance,
>> > Deniz
>>
>> --
>> Posted via a free Usenet account fromhttp://www.teranews.com
>
> First of all thank you all guys,
> I'll first check the angles, but i was quite carefull installing the
> shaft. The d44 i bought was a second hand one and it was in a very
> good condition, unfortunately without a drive shaft. To be honest i
> hadn't measured the housings. But by the look of the mud marks and
> clean parts of the shaft i can tell that it's standing a wee bit
> longer. I'll try to find an old jeep on the road and stop it and get
> under to measure the shaft unfortunately there arent't many of those.
> The cv shaft option is gonna have to wait till i get the lift kit as i
> understand that i need to change the angles of the spring perches and
> i don't want to take the the axle off again, i wanna drive it for a
> while as i'd been working on it for quite some time, i missed the
> little beasty. I'll replace the u joints as well once i measure a D44
> drive shaft. The u joints are a couple of years old but i hadn't
> maintained them regularly.
> Thank you all again.
>
> Deniz
>
Guest
Posts: n/a
Re: amc 20 dana 44 replacement
I'll go out and measure my AMC 20 when it gets light out, will post in an
hour or so.
"Deniz" <dhasirci@gmail.com> wrote in message
news:1175755955.763919.258190@p77g2000hsh.googlegr oups.com...
> On 5 Nisan, 06:53, "L.W. \(Bill\) ------ III" <billhug...@***.net>
> wrote:
>>
>> http://www.4xshaft.com/driveline101....com/index.html
>> God Bless America, Bill 0|||||||0
>> mailto:LW------...@aol.comhttp://www.----------.com/
>>
>> "Deniz" <dhasi...@gmail.com> wrote in message
>>
>> news:1175674679.158682.313630@d57g2000hsg.googlegr oups.com...
>>
>> > Hi guys,
>> > I'm from Turkey and i have 79 cj5. Recently i have replaced my amc 20
>> > with a dana 44. But some vibrations occured both while accelerating
>> > and decelerating probably because of the rear driveshaft.It's a bit
>> > difficult to find parts for cjs in Turkey, i need to have some parts
>> > made customly. Do i need a longer driveshaft as it looks slightly
>> > longer now the it used to be or should i try to have a cv type drive
>> > shaft custom made as i'm thinking of buying a 2 inch lift kit in the
>> > near future? With a cv drive shaft do i need transfer case lowering
>> > kit for 2 inch lift?
>> > Thank you all in advance,
>> > Deniz
>>
>> --
>> Posted via a free Usenet account fromhttp://www.teranews.com
>
> First of all thank you all guys,
> I'll first check the angles, but i was quite carefull installing the
> shaft. The d44 i bought was a second hand one and it was in a very
> good condition, unfortunately without a drive shaft. To be honest i
> hadn't measured the housings. But by the look of the mud marks and
> clean parts of the shaft i can tell that it's standing a wee bit
> longer. I'll try to find an old jeep on the road and stop it and get
> under to measure the shaft unfortunately there arent't many of those.
> The cv shaft option is gonna have to wait till i get the lift kit as i
> understand that i need to change the angles of the spring perches and
> i don't want to take the the axle off again, i wanna drive it for a
> while as i'd been working on it for quite some time, i missed the
> little beasty. I'll replace the u joints as well once i measure a D44
> drive shaft. The u joints are a couple of years old but i hadn't
> maintained them regularly.
> Thank you all again.
>
> Deniz
>
hour or so.
"Deniz" <dhasirci@gmail.com> wrote in message
news:1175755955.763919.258190@p77g2000hsh.googlegr oups.com...
> On 5 Nisan, 06:53, "L.W. \(Bill\) ------ III" <billhug...@***.net>
> wrote:
>>
>> http://www.4xshaft.com/driveline101....com/index.html
>> God Bless America, Bill 0|||||||0
>> mailto:LW------...@aol.comhttp://www.----------.com/
>>
>> "Deniz" <dhasi...@gmail.com> wrote in message
>>
>> news:1175674679.158682.313630@d57g2000hsg.googlegr oups.com...
>>
>> > Hi guys,
>> > I'm from Turkey and i have 79 cj5. Recently i have replaced my amc 20
>> > with a dana 44. But some vibrations occured both while accelerating
>> > and decelerating probably because of the rear driveshaft.It's a bit
>> > difficult to find parts for cjs in Turkey, i need to have some parts
>> > made customly. Do i need a longer driveshaft as it looks slightly
>> > longer now the it used to be or should i try to have a cv type drive
>> > shaft custom made as i'm thinking of buying a 2 inch lift kit in the
>> > near future? With a cv drive shaft do i need transfer case lowering
>> > kit for 2 inch lift?
>> > Thank you all in advance,
>> > Deniz
>>
>> --
>> Posted via a free Usenet account fromhttp://www.teranews.com
>
> First of all thank you all guys,
> I'll first check the angles, but i was quite carefull installing the
> shaft. The d44 i bought was a second hand one and it was in a very
> good condition, unfortunately without a drive shaft. To be honest i
> hadn't measured the housings. But by the look of the mud marks and
> clean parts of the shaft i can tell that it's standing a wee bit
> longer. I'll try to find an old jeep on the road and stop it and get
> under to measure the shaft unfortunately there arent't many of those.
> The cv shaft option is gonna have to wait till i get the lift kit as i
> understand that i need to change the angles of the spring perches and
> i don't want to take the the axle off again, i wanna drive it for a
> while as i'd been working on it for quite some time, i missed the
> little beasty. I'll replace the u joints as well once i measure a D44
> drive shaft. The u joints are a couple of years old but i hadn't
> maintained them regularly.
> Thank you all again.
>
> Deniz
>
Guest
Posts: n/a
Re: amc 20 dana 44 replacement
Looks like 10 5/8", or 27 cm from center of axle tube to front face of
housing, yoke not included.
"Greg" <greglc84@hotmail.com> wrote in message
news:bD6Rh.32235$DE1.13836@pd7urf2no...
> I'll go out and measure my AMC 20 when it gets light out, will post in an
> hour or so.
>
> "Deniz" <dhasirci@gmail.com> wrote in message
> news:1175755955.763919.258190@p77g2000hsh.googlegr oups.com...
>> On 5 Nisan, 06:53, "L.W. \(Bill\) ------ III" <billhug...@***.net>
>> wrote:
>>>
>>> http://www.4xshaft.com/driveline101....com/index.html
>>> God Bless America, Bill 0|||||||0
>>> mailto:LW------...@aol.comhttp://www.----------.com/
>>>
>>> "Deniz" <dhasi...@gmail.com> wrote in message
>>>
>>> news:1175674679.158682.313630@d57g2000hsg.googlegr oups.com...
>>>
>>> > Hi guys,
>>> > I'm from Turkey and i have 79 cj5. Recently i have replaced my amc 20
>>> > with a dana 44. But some vibrations occured both while accelerating
>>> > and decelerating probably because of the rear driveshaft.It's a bit
>>> > difficult to find parts for cjs in Turkey, i need to have some parts
>>> > made customly. Do i need a longer driveshaft as it looks slightly
>>> > longer now the it used to be or should i try to have a cv type drive
>>> > shaft custom made as i'm thinking of buying a 2 inch lift kit in the
>>> > near future? With a cv drive shaft do i need transfer case lowering
>>> > kit for 2 inch lift?
>>> > Thank you all in advance,
>>> > Deniz
>>>
>>> --
>>> Posted via a free Usenet account fromhttp://www.teranews.com
>>
>> First of all thank you all guys,
>> I'll first check the angles, but i was quite carefull installing the
>> shaft. The d44 i bought was a second hand one and it was in a very
>> good condition, unfortunately without a drive shaft. To be honest i
>> hadn't measured the housings. But by the look of the mud marks and
>> clean parts of the shaft i can tell that it's standing a wee bit
>> longer. I'll try to find an old jeep on the road and stop it and get
>> under to measure the shaft unfortunately there arent't many of those.
>> The cv shaft option is gonna have to wait till i get the lift kit as i
>> understand that i need to change the angles of the spring perches and
>> i don't want to take the the axle off again, i wanna drive it for a
>> while as i'd been working on it for quite some time, i missed the
>> little beasty. I'll replace the u joints as well once i measure a D44
>> drive shaft. The u joints are a couple of years old but i hadn't
>> maintained them regularly.
>> Thank you all again.
>>
>> Deniz
>>
>
>
housing, yoke not included.
"Greg" <greglc84@hotmail.com> wrote in message
news:bD6Rh.32235$DE1.13836@pd7urf2no...
> I'll go out and measure my AMC 20 when it gets light out, will post in an
> hour or so.
>
> "Deniz" <dhasirci@gmail.com> wrote in message
> news:1175755955.763919.258190@p77g2000hsh.googlegr oups.com...
>> On 5 Nisan, 06:53, "L.W. \(Bill\) ------ III" <billhug...@***.net>
>> wrote:
>>>
>>> http://www.4xshaft.com/driveline101....com/index.html
>>> God Bless America, Bill 0|||||||0
>>> mailto:LW------...@aol.comhttp://www.----------.com/
>>>
>>> "Deniz" <dhasi...@gmail.com> wrote in message
>>>
>>> news:1175674679.158682.313630@d57g2000hsg.googlegr oups.com...
>>>
>>> > Hi guys,
>>> > I'm from Turkey and i have 79 cj5. Recently i have replaced my amc 20
>>> > with a dana 44. But some vibrations occured both while accelerating
>>> > and decelerating probably because of the rear driveshaft.It's a bit
>>> > difficult to find parts for cjs in Turkey, i need to have some parts
>>> > made customly. Do i need a longer driveshaft as it looks slightly
>>> > longer now the it used to be or should i try to have a cv type drive
>>> > shaft custom made as i'm thinking of buying a 2 inch lift kit in the
>>> > near future? With a cv drive shaft do i need transfer case lowering
>>> > kit for 2 inch lift?
>>> > Thank you all in advance,
>>> > Deniz
>>>
>>> --
>>> Posted via a free Usenet account fromhttp://www.teranews.com
>>
>> First of all thank you all guys,
>> I'll first check the angles, but i was quite carefull installing the
>> shaft. The d44 i bought was a second hand one and it was in a very
>> good condition, unfortunately without a drive shaft. To be honest i
>> hadn't measured the housings. But by the look of the mud marks and
>> clean parts of the shaft i can tell that it's standing a wee bit
>> longer. I'll try to find an old jeep on the road and stop it and get
>> under to measure the shaft unfortunately there arent't many of those.
>> The cv shaft option is gonna have to wait till i get the lift kit as i
>> understand that i need to change the angles of the spring perches and
>> i don't want to take the the axle off again, i wanna drive it for a
>> while as i'd been working on it for quite some time, i missed the
>> little beasty. I'll replace the u joints as well once i measure a D44
>> drive shaft. The u joints are a couple of years old but i hadn't
>> maintained them regularly.
>> Thank you all again.
>>
>> Deniz
>>
>
>
Guest
Posts: n/a
Re: amc 20 dana 44 replacement
Looks like 10 5/8", or 27 cm from center of axle tube to front face of
housing, yoke not included.
"Greg" <greglc84@hotmail.com> wrote in message
news:bD6Rh.32235$DE1.13836@pd7urf2no...
> I'll go out and measure my AMC 20 when it gets light out, will post in an
> hour or so.
>
> "Deniz" <dhasirci@gmail.com> wrote in message
> news:1175755955.763919.258190@p77g2000hsh.googlegr oups.com...
>> On 5 Nisan, 06:53, "L.W. \(Bill\) ------ III" <billhug...@***.net>
>> wrote:
>>>
>>> http://www.4xshaft.com/driveline101....com/index.html
>>> God Bless America, Bill 0|||||||0
>>> mailto:LW------...@aol.comhttp://www.----------.com/
>>>
>>> "Deniz" <dhasi...@gmail.com> wrote in message
>>>
>>> news:1175674679.158682.313630@d57g2000hsg.googlegr oups.com...
>>>
>>> > Hi guys,
>>> > I'm from Turkey and i have 79 cj5. Recently i have replaced my amc 20
>>> > with a dana 44. But some vibrations occured both while accelerating
>>> > and decelerating probably because of the rear driveshaft.It's a bit
>>> > difficult to find parts for cjs in Turkey, i need to have some parts
>>> > made customly. Do i need a longer driveshaft as it looks slightly
>>> > longer now the it used to be or should i try to have a cv type drive
>>> > shaft custom made as i'm thinking of buying a 2 inch lift kit in the
>>> > near future? With a cv drive shaft do i need transfer case lowering
>>> > kit for 2 inch lift?
>>> > Thank you all in advance,
>>> > Deniz
>>>
>>> --
>>> Posted via a free Usenet account fromhttp://www.teranews.com
>>
>> First of all thank you all guys,
>> I'll first check the angles, but i was quite carefull installing the
>> shaft. The d44 i bought was a second hand one and it was in a very
>> good condition, unfortunately without a drive shaft. To be honest i
>> hadn't measured the housings. But by the look of the mud marks and
>> clean parts of the shaft i can tell that it's standing a wee bit
>> longer. I'll try to find an old jeep on the road and stop it and get
>> under to measure the shaft unfortunately there arent't many of those.
>> The cv shaft option is gonna have to wait till i get the lift kit as i
>> understand that i need to change the angles of the spring perches and
>> i don't want to take the the axle off again, i wanna drive it for a
>> while as i'd been working on it for quite some time, i missed the
>> little beasty. I'll replace the u joints as well once i measure a D44
>> drive shaft. The u joints are a couple of years old but i hadn't
>> maintained them regularly.
>> Thank you all again.
>>
>> Deniz
>>
>
>
housing, yoke not included.
"Greg" <greglc84@hotmail.com> wrote in message
news:bD6Rh.32235$DE1.13836@pd7urf2no...
> I'll go out and measure my AMC 20 when it gets light out, will post in an
> hour or so.
>
> "Deniz" <dhasirci@gmail.com> wrote in message
> news:1175755955.763919.258190@p77g2000hsh.googlegr oups.com...
>> On 5 Nisan, 06:53, "L.W. \(Bill\) ------ III" <billhug...@***.net>
>> wrote:
>>>
>>> http://www.4xshaft.com/driveline101....com/index.html
>>> God Bless America, Bill 0|||||||0
>>> mailto:LW------...@aol.comhttp://www.----------.com/
>>>
>>> "Deniz" <dhasi...@gmail.com> wrote in message
>>>
>>> news:1175674679.158682.313630@d57g2000hsg.googlegr oups.com...
>>>
>>> > Hi guys,
>>> > I'm from Turkey and i have 79 cj5. Recently i have replaced my amc 20
>>> > with a dana 44. But some vibrations occured both while accelerating
>>> > and decelerating probably because of the rear driveshaft.It's a bit
>>> > difficult to find parts for cjs in Turkey, i need to have some parts
>>> > made customly. Do i need a longer driveshaft as it looks slightly
>>> > longer now the it used to be or should i try to have a cv type drive
>>> > shaft custom made as i'm thinking of buying a 2 inch lift kit in the
>>> > near future? With a cv drive shaft do i need transfer case lowering
>>> > kit for 2 inch lift?
>>> > Thank you all in advance,
>>> > Deniz
>>>
>>> --
>>> Posted via a free Usenet account fromhttp://www.teranews.com
>>
>> First of all thank you all guys,
>> I'll first check the angles, but i was quite carefull installing the
>> shaft. The d44 i bought was a second hand one and it was in a very
>> good condition, unfortunately without a drive shaft. To be honest i
>> hadn't measured the housings. But by the look of the mud marks and
>> clean parts of the shaft i can tell that it's standing a wee bit
>> longer. I'll try to find an old jeep on the road and stop it and get
>> under to measure the shaft unfortunately there arent't many of those.
>> The cv shaft option is gonna have to wait till i get the lift kit as i
>> understand that i need to change the angles of the spring perches and
>> i don't want to take the the axle off again, i wanna drive it for a
>> while as i'd been working on it for quite some time, i missed the
>> little beasty. I'll replace the u joints as well once i measure a D44
>> drive shaft. The u joints are a couple of years old but i hadn't
>> maintained them regularly.
>> Thank you all again.
>>
>> Deniz
>>
>
>
Guest
Posts: n/a
Re: amc 20 dana 44 replacement
Looks like 10 5/8", or 27 cm from center of axle tube to front face of
housing, yoke not included.
"Greg" <greglc84@hotmail.com> wrote in message
news:bD6Rh.32235$DE1.13836@pd7urf2no...
> I'll go out and measure my AMC 20 when it gets light out, will post in an
> hour or so.
>
> "Deniz" <dhasirci@gmail.com> wrote in message
> news:1175755955.763919.258190@p77g2000hsh.googlegr oups.com...
>> On 5 Nisan, 06:53, "L.W. \(Bill\) ------ III" <billhug...@***.net>
>> wrote:
>>>
>>> http://www.4xshaft.com/driveline101....com/index.html
>>> God Bless America, Bill 0|||||||0
>>> mailto:LW------...@aol.comhttp://www.----------.com/
>>>
>>> "Deniz" <dhasi...@gmail.com> wrote in message
>>>
>>> news:1175674679.158682.313630@d57g2000hsg.googlegr oups.com...
>>>
>>> > Hi guys,
>>> > I'm from Turkey and i have 79 cj5. Recently i have replaced my amc 20
>>> > with a dana 44. But some vibrations occured both while accelerating
>>> > and decelerating probably because of the rear driveshaft.It's a bit
>>> > difficult to find parts for cjs in Turkey, i need to have some parts
>>> > made customly. Do i need a longer driveshaft as it looks slightly
>>> > longer now the it used to be or should i try to have a cv type drive
>>> > shaft custom made as i'm thinking of buying a 2 inch lift kit in the
>>> > near future? With a cv drive shaft do i need transfer case lowering
>>> > kit for 2 inch lift?
>>> > Thank you all in advance,
>>> > Deniz
>>>
>>> --
>>> Posted via a free Usenet account fromhttp://www.teranews.com
>>
>> First of all thank you all guys,
>> I'll first check the angles, but i was quite carefull installing the
>> shaft. The d44 i bought was a second hand one and it was in a very
>> good condition, unfortunately without a drive shaft. To be honest i
>> hadn't measured the housings. But by the look of the mud marks and
>> clean parts of the shaft i can tell that it's standing a wee bit
>> longer. I'll try to find an old jeep on the road and stop it and get
>> under to measure the shaft unfortunately there arent't many of those.
>> The cv shaft option is gonna have to wait till i get the lift kit as i
>> understand that i need to change the angles of the spring perches and
>> i don't want to take the the axle off again, i wanna drive it for a
>> while as i'd been working on it for quite some time, i missed the
>> little beasty. I'll replace the u joints as well once i measure a D44
>> drive shaft. The u joints are a couple of years old but i hadn't
>> maintained them regularly.
>> Thank you all again.
>>
>> Deniz
>>
>
>
housing, yoke not included.
"Greg" <greglc84@hotmail.com> wrote in message
news:bD6Rh.32235$DE1.13836@pd7urf2no...
> I'll go out and measure my AMC 20 when it gets light out, will post in an
> hour or so.
>
> "Deniz" <dhasirci@gmail.com> wrote in message
> news:1175755955.763919.258190@p77g2000hsh.googlegr oups.com...
>> On 5 Nisan, 06:53, "L.W. \(Bill\) ------ III" <billhug...@***.net>
>> wrote:
>>>
>>> http://www.4xshaft.com/driveline101....com/index.html
>>> God Bless America, Bill 0|||||||0
>>> mailto:LW------...@aol.comhttp://www.----------.com/
>>>
>>> "Deniz" <dhasi...@gmail.com> wrote in message
>>>
>>> news:1175674679.158682.313630@d57g2000hsg.googlegr oups.com...
>>>
>>> > Hi guys,
>>> > I'm from Turkey and i have 79 cj5. Recently i have replaced my amc 20
>>> > with a dana 44. But some vibrations occured both while accelerating
>>> > and decelerating probably because of the rear driveshaft.It's a bit
>>> > difficult to find parts for cjs in Turkey, i need to have some parts
>>> > made customly. Do i need a longer driveshaft as it looks slightly
>>> > longer now the it used to be or should i try to have a cv type drive
>>> > shaft custom made as i'm thinking of buying a 2 inch lift kit in the
>>> > near future? With a cv drive shaft do i need transfer case lowering
>>> > kit for 2 inch lift?
>>> > Thank you all in advance,
>>> > Deniz
>>>
>>> --
>>> Posted via a free Usenet account fromhttp://www.teranews.com
>>
>> First of all thank you all guys,
>> I'll first check the angles, but i was quite carefull installing the
>> shaft. The d44 i bought was a second hand one and it was in a very
>> good condition, unfortunately without a drive shaft. To be honest i
>> hadn't measured the housings. But by the look of the mud marks and
>> clean parts of the shaft i can tell that it's standing a wee bit
>> longer. I'll try to find an old jeep on the road and stop it and get
>> under to measure the shaft unfortunately there arent't many of those.
>> The cv shaft option is gonna have to wait till i get the lift kit as i
>> understand that i need to change the angles of the spring perches and
>> i don't want to take the the axle off again, i wanna drive it for a
>> while as i'd been working on it for quite some time, i missed the
>> little beasty. I'll replace the u joints as well once i measure a D44
>> drive shaft. The u joints are a couple of years old but i hadn't
>> maintained them regularly.
>> Thank you all again.
>>
>> Deniz
>>
>
>
Guest
Posts: n/a
Re: amc 20 dana 44 replacement
On 5 Nisan, 17:39, "Greg" <gregl...@hotmail.com> wrote:
> Looks like 10 5/8", or 27 cm from center of axle tube to front face of
> housing, yoke not included.
>
> "Greg" <gregl...@hotmail.com> wrote in message
>
> news:bD6Rh.32235$DE1.13836@pd7urf2no...
>
>
>
> > I'll go out and measure my AMC 20 when it gets light out, will post inan
> > hour or so.
>
> > "Deniz" <dhasi...@gmail.com> wrote in message
> >news:1175755955.763919.258190@p77g2000hsh.googleg roups.com...
> >> On 5 Nisan, 06:53, "L.W. \(Bill\) ------ III" <billhug...@***.net>
> >> wrote:
>
> >>>http://www.4xshaft.com/driveline101....te4x4.com/tech....
> >>> God Bless America, Bill 0|||||||0
> >>> mailto:LW------...@aol.comhttp://www.----------.com/
>
> >>> "Deniz" <dhasi...@gmail.com> wrote in message
>
> >>>news:1175674679.158682.313630@d57g2000hsg.googl egroups.com...
>
> >>> > Hi guys,
> >>> > I'm from Turkey and i have 79 cj5. Recently i have replaced my amc 20
> >>> > with a dana 44. But some vibrations occured both while accelerating
> >>> > and decelerating probably because of the rear driveshaft.It's a bit
> >>> > difficult to find parts for cjs in Turkey, i need to have some parts
> >>> > made customly. Do i need a longer driveshaft as it looks slightly
> >>> > longer now the it used to be or should i try to have a cv type drive
> >>> > shaft custom made as i'm thinking of buying a 2 inch lift kit in the
> >>> > near future? With a cv drive shaft do i need transfer case lowering
> >>> > kit for 2 inch lift?
> >>> > Thank you all in advance,
> >>> > Deniz
>
> >>> --
> >>> Posted via a free Usenet account fromhttp://www.teranews.com
>
> >> First of all thank you all guys,
> >> I'll first check the angles, but i was quite carefull installing the
> >> shaft. The d44 i bought was a second hand one and it was in a very
> >> good condition, unfortunately without a drive shaft. To be honest i
> >> hadn't measured the housings. But by the look of the mud marks and
> >> clean parts of the shaft i can tell that it's standing a wee bit
> >> longer. I'll try to find an old jeep on the road and stop it and get
> >> under to measure the shaft unfortunately there arent't many of those.
> >> The cv shaft option is gonna have to wait till i get the lift kit as i
> >> understand that i need to change the angles of the spring perches and
> >> i don't want to take the the axle off again, i wanna drive it for a
> >> while as i'd been working on it for quite some time, i missed the
> >> little beasty. I'll replace the u joints as well once i measure a D44
> >> drive shaft. The u joints are a couple of years old but i hadn't
> >> maintained them regularly.
> >> Thank you all again.
>
> >> Deniz- Alıntıyı gizle -
>
> - Alıntıyı göster -
Thanks Greg,
I'll go an measure mine before it gets dark at this side of
Greenwich:)
Deniz
> Looks like 10 5/8", or 27 cm from center of axle tube to front face of
> housing, yoke not included.
>
> "Greg" <gregl...@hotmail.com> wrote in message
>
> news:bD6Rh.32235$DE1.13836@pd7urf2no...
>
>
>
> > I'll go out and measure my AMC 20 when it gets light out, will post inan
> > hour or so.
>
> > "Deniz" <dhasi...@gmail.com> wrote in message
> >news:1175755955.763919.258190@p77g2000hsh.googleg roups.com...
> >> On 5 Nisan, 06:53, "L.W. \(Bill\) ------ III" <billhug...@***.net>
> >> wrote:
>
> >>>http://www.4xshaft.com/driveline101....te4x4.com/tech....
> >>> God Bless America, Bill 0|||||||0
> >>> mailto:LW------...@aol.comhttp://www.----------.com/
>
> >>> "Deniz" <dhasi...@gmail.com> wrote in message
>
> >>>news:1175674679.158682.313630@d57g2000hsg.googl egroups.com...
>
> >>> > Hi guys,
> >>> > I'm from Turkey and i have 79 cj5. Recently i have replaced my amc 20
> >>> > with a dana 44. But some vibrations occured both while accelerating
> >>> > and decelerating probably because of the rear driveshaft.It's a bit
> >>> > difficult to find parts for cjs in Turkey, i need to have some parts
> >>> > made customly. Do i need a longer driveshaft as it looks slightly
> >>> > longer now the it used to be or should i try to have a cv type drive
> >>> > shaft custom made as i'm thinking of buying a 2 inch lift kit in the
> >>> > near future? With a cv drive shaft do i need transfer case lowering
> >>> > kit for 2 inch lift?
> >>> > Thank you all in advance,
> >>> > Deniz
>
> >>> --
> >>> Posted via a free Usenet account fromhttp://www.teranews.com
>
> >> First of all thank you all guys,
> >> I'll first check the angles, but i was quite carefull installing the
> >> shaft. The d44 i bought was a second hand one and it was in a very
> >> good condition, unfortunately without a drive shaft. To be honest i
> >> hadn't measured the housings. But by the look of the mud marks and
> >> clean parts of the shaft i can tell that it's standing a wee bit
> >> longer. I'll try to find an old jeep on the road and stop it and get
> >> under to measure the shaft unfortunately there arent't many of those.
> >> The cv shaft option is gonna have to wait till i get the lift kit as i
> >> understand that i need to change the angles of the spring perches and
> >> i don't want to take the the axle off again, i wanna drive it for a
> >> while as i'd been working on it for quite some time, i missed the
> >> little beasty. I'll replace the u joints as well once i measure a D44
> >> drive shaft. The u joints are a couple of years old but i hadn't
> >> maintained them regularly.
> >> Thank you all again.
>
> >> Deniz- Alıntıyı gizle -
>
> - Alıntıyı göster -
Thanks Greg,
I'll go an measure mine before it gets dark at this side of
Greenwich:)
Deniz
Guest
Posts: n/a
Re: amc 20 dana 44 replacement
On 5 Nisan, 17:39, "Greg" <gregl...@hotmail.com> wrote:
> Looks like 10 5/8", or 27 cm from center of axle tube to front face of
> housing, yoke not included.
>
> "Greg" <gregl...@hotmail.com> wrote in message
>
> news:bD6Rh.32235$DE1.13836@pd7urf2no...
>
>
>
> > I'll go out and measure my AMC 20 when it gets light out, will post inan
> > hour or so.
>
> > "Deniz" <dhasi...@gmail.com> wrote in message
> >news:1175755955.763919.258190@p77g2000hsh.googleg roups.com...
> >> On 5 Nisan, 06:53, "L.W. \(Bill\) ------ III" <billhug...@***.net>
> >> wrote:
>
> >>>http://www.4xshaft.com/driveline101....te4x4.com/tech....
> >>> God Bless America, Bill 0|||||||0
> >>> mailto:LW------...@aol.comhttp://www.----------.com/
>
> >>> "Deniz" <dhasi...@gmail.com> wrote in message
>
> >>>news:1175674679.158682.313630@d57g2000hsg.googl egroups.com...
>
> >>> > Hi guys,
> >>> > I'm from Turkey and i have 79 cj5. Recently i have replaced my amc 20
> >>> > with a dana 44. But some vibrations occured both while accelerating
> >>> > and decelerating probably because of the rear driveshaft.It's a bit
> >>> > difficult to find parts for cjs in Turkey, i need to have some parts
> >>> > made customly. Do i need a longer driveshaft as it looks slightly
> >>> > longer now the it used to be or should i try to have a cv type drive
> >>> > shaft custom made as i'm thinking of buying a 2 inch lift kit in the
> >>> > near future? With a cv drive shaft do i need transfer case lowering
> >>> > kit for 2 inch lift?
> >>> > Thank you all in advance,
> >>> > Deniz
>
> >>> --
> >>> Posted via a free Usenet account fromhttp://www.teranews.com
>
> >> First of all thank you all guys,
> >> I'll first check the angles, but i was quite carefull installing the
> >> shaft. The d44 i bought was a second hand one and it was in a very
> >> good condition, unfortunately without a drive shaft. To be honest i
> >> hadn't measured the housings. But by the look of the mud marks and
> >> clean parts of the shaft i can tell that it's standing a wee bit
> >> longer. I'll try to find an old jeep on the road and stop it and get
> >> under to measure the shaft unfortunately there arent't many of those.
> >> The cv shaft option is gonna have to wait till i get the lift kit as i
> >> understand that i need to change the angles of the spring perches and
> >> i don't want to take the the axle off again, i wanna drive it for a
> >> while as i'd been working on it for quite some time, i missed the
> >> little beasty. I'll replace the u joints as well once i measure a D44
> >> drive shaft. The u joints are a couple of years old but i hadn't
> >> maintained them regularly.
> >> Thank you all again.
>
> >> Deniz- Alıntıyı gizle -
>
> - Alıntıyı göster -
Thanks Greg,
I'll go an measure mine before it gets dark at this side of
Greenwich:)
Deniz
> Looks like 10 5/8", or 27 cm from center of axle tube to front face of
> housing, yoke not included.
>
> "Greg" <gregl...@hotmail.com> wrote in message
>
> news:bD6Rh.32235$DE1.13836@pd7urf2no...
>
>
>
> > I'll go out and measure my AMC 20 when it gets light out, will post inan
> > hour or so.
>
> > "Deniz" <dhasi...@gmail.com> wrote in message
> >news:1175755955.763919.258190@p77g2000hsh.googleg roups.com...
> >> On 5 Nisan, 06:53, "L.W. \(Bill\) ------ III" <billhug...@***.net>
> >> wrote:
>
> >>>http://www.4xshaft.com/driveline101....te4x4.com/tech....
> >>> God Bless America, Bill 0|||||||0
> >>> mailto:LW------...@aol.comhttp://www.----------.com/
>
> >>> "Deniz" <dhasi...@gmail.com> wrote in message
>
> >>>news:1175674679.158682.313630@d57g2000hsg.googl egroups.com...
>
> >>> > Hi guys,
> >>> > I'm from Turkey and i have 79 cj5. Recently i have replaced my amc 20
> >>> > with a dana 44. But some vibrations occured both while accelerating
> >>> > and decelerating probably because of the rear driveshaft.It's a bit
> >>> > difficult to find parts for cjs in Turkey, i need to have some parts
> >>> > made customly. Do i need a longer driveshaft as it looks slightly
> >>> > longer now the it used to be or should i try to have a cv type drive
> >>> > shaft custom made as i'm thinking of buying a 2 inch lift kit in the
> >>> > near future? With a cv drive shaft do i need transfer case lowering
> >>> > kit for 2 inch lift?
> >>> > Thank you all in advance,
> >>> > Deniz
>
> >>> --
> >>> Posted via a free Usenet account fromhttp://www.teranews.com
>
> >> First of all thank you all guys,
> >> I'll first check the angles, but i was quite carefull installing the
> >> shaft. The d44 i bought was a second hand one and it was in a very
> >> good condition, unfortunately without a drive shaft. To be honest i
> >> hadn't measured the housings. But by the look of the mud marks and
> >> clean parts of the shaft i can tell that it's standing a wee bit
> >> longer. I'll try to find an old jeep on the road and stop it and get
> >> under to measure the shaft unfortunately there arent't many of those.
> >> The cv shaft option is gonna have to wait till i get the lift kit as i
> >> understand that i need to change the angles of the spring perches and
> >> i don't want to take the the axle off again, i wanna drive it for a
> >> while as i'd been working on it for quite some time, i missed the
> >> little beasty. I'll replace the u joints as well once i measure a D44
> >> drive shaft. The u joints are a couple of years old but i hadn't
> >> maintained them regularly.
> >> Thank you all again.
>
> >> Deniz- Alıntıyı gizle -
>
> - Alıntıyı göster -
Thanks Greg,
I'll go an measure mine before it gets dark at this side of
Greenwich:)
Deniz
Guest
Posts: n/a
Re: amc 20 dana 44 replacement
On 5 Nisan, 17:39, "Greg" <gregl...@hotmail.com> wrote:
> Looks like 10 5/8", or 27 cm from center of axle tube to front face of
> housing, yoke not included.
>
> "Greg" <gregl...@hotmail.com> wrote in message
>
> news:bD6Rh.32235$DE1.13836@pd7urf2no...
>
>
>
> > I'll go out and measure my AMC 20 when it gets light out, will post inan
> > hour or so.
>
> > "Deniz" <dhasi...@gmail.com> wrote in message
> >news:1175755955.763919.258190@p77g2000hsh.googleg roups.com...
> >> On 5 Nisan, 06:53, "L.W. \(Bill\) ------ III" <billhug...@***.net>
> >> wrote:
>
> >>>http://www.4xshaft.com/driveline101....te4x4.com/tech....
> >>> God Bless America, Bill 0|||||||0
> >>> mailto:LW------...@aol.comhttp://www.----------.com/
>
> >>> "Deniz" <dhasi...@gmail.com> wrote in message
>
> >>>news:1175674679.158682.313630@d57g2000hsg.googl egroups.com...
>
> >>> > Hi guys,
> >>> > I'm from Turkey and i have 79 cj5. Recently i have replaced my amc 20
> >>> > with a dana 44. But some vibrations occured both while accelerating
> >>> > and decelerating probably because of the rear driveshaft.It's a bit
> >>> > difficult to find parts for cjs in Turkey, i need to have some parts
> >>> > made customly. Do i need a longer driveshaft as it looks slightly
> >>> > longer now the it used to be or should i try to have a cv type drive
> >>> > shaft custom made as i'm thinking of buying a 2 inch lift kit in the
> >>> > near future? With a cv drive shaft do i need transfer case lowering
> >>> > kit for 2 inch lift?
> >>> > Thank you all in advance,
> >>> > Deniz
>
> >>> --
> >>> Posted via a free Usenet account fromhttp://www.teranews.com
>
> >> First of all thank you all guys,
> >> I'll first check the angles, but i was quite carefull installing the
> >> shaft. The d44 i bought was a second hand one and it was in a very
> >> good condition, unfortunately without a drive shaft. To be honest i
> >> hadn't measured the housings. But by the look of the mud marks and
> >> clean parts of the shaft i can tell that it's standing a wee bit
> >> longer. I'll try to find an old jeep on the road and stop it and get
> >> under to measure the shaft unfortunately there arent't many of those.
> >> The cv shaft option is gonna have to wait till i get the lift kit as i
> >> understand that i need to change the angles of the spring perches and
> >> i don't want to take the the axle off again, i wanna drive it for a
> >> while as i'd been working on it for quite some time, i missed the
> >> little beasty. I'll replace the u joints as well once i measure a D44
> >> drive shaft. The u joints are a couple of years old but i hadn't
> >> maintained them regularly.
> >> Thank you all again.
>
> >> Deniz- Alıntıyı gizle -
>
> - Alıntıyı göster -
Thanks Greg,
I'll go an measure mine before it gets dark at this side of
Greenwich:)
Deniz
> Looks like 10 5/8", or 27 cm from center of axle tube to front face of
> housing, yoke not included.
>
> "Greg" <gregl...@hotmail.com> wrote in message
>
> news:bD6Rh.32235$DE1.13836@pd7urf2no...
>
>
>
> > I'll go out and measure my AMC 20 when it gets light out, will post inan
> > hour or so.
>
> > "Deniz" <dhasi...@gmail.com> wrote in message
> >news:1175755955.763919.258190@p77g2000hsh.googleg roups.com...
> >> On 5 Nisan, 06:53, "L.W. \(Bill\) ------ III" <billhug...@***.net>
> >> wrote:
>
> >>>http://www.4xshaft.com/driveline101....te4x4.com/tech....
> >>> God Bless America, Bill 0|||||||0
> >>> mailto:LW------...@aol.comhttp://www.----------.com/
>
> >>> "Deniz" <dhasi...@gmail.com> wrote in message
>
> >>>news:1175674679.158682.313630@d57g2000hsg.googl egroups.com...
>
> >>> > Hi guys,
> >>> > I'm from Turkey and i have 79 cj5. Recently i have replaced my amc 20
> >>> > with a dana 44. But some vibrations occured both while accelerating
> >>> > and decelerating probably because of the rear driveshaft.It's a bit
> >>> > difficult to find parts for cjs in Turkey, i need to have some parts
> >>> > made customly. Do i need a longer driveshaft as it looks slightly
> >>> > longer now the it used to be or should i try to have a cv type drive
> >>> > shaft custom made as i'm thinking of buying a 2 inch lift kit in the
> >>> > near future? With a cv drive shaft do i need transfer case lowering
> >>> > kit for 2 inch lift?
> >>> > Thank you all in advance,
> >>> > Deniz
>
> >>> --
> >>> Posted via a free Usenet account fromhttp://www.teranews.com
>
> >> First of all thank you all guys,
> >> I'll first check the angles, but i was quite carefull installing the
> >> shaft. The d44 i bought was a second hand one and it was in a very
> >> good condition, unfortunately without a drive shaft. To be honest i
> >> hadn't measured the housings. But by the look of the mud marks and
> >> clean parts of the shaft i can tell that it's standing a wee bit
> >> longer. I'll try to find an old jeep on the road and stop it and get
> >> under to measure the shaft unfortunately there arent't many of those.
> >> The cv shaft option is gonna have to wait till i get the lift kit as i
> >> understand that i need to change the angles of the spring perches and
> >> i don't want to take the the axle off again, i wanna drive it for a
> >> while as i'd been working on it for quite some time, i missed the
> >> little beasty. I'll replace the u joints as well once i measure a D44
> >> drive shaft. The u joints are a couple of years old but i hadn't
> >> maintained them regularly.
> >> Thank you all again.
>
> >> Deniz- Alıntıyı gizle -
>
> - Alıntıyı göster -
Thanks Greg,
I'll go an measure mine before it gets dark at this side of
Greenwich:)
Deniz
Guest
Posts: n/a
Re: amc 20 dana 44 replacement
"Deniz" <dhasirci@gmail.com> wrote in message
news:1175785537.830895.197320@e65g2000hsc.googlegr oups.com...
On 5 Nisan, 17:39, "Greg" <gregl...@hotmail.com> wrote:
> Looks like 10 5/8", or 27 cm from center of axle tube to front face of
> housing, yoke not included.
>
> "Greg" <gregl...@hotmail.com> wrote in message
>
> news:bD6Rh.32235$DE1.13836@pd7urf2no...
>
>
>
> > I'll go out and measure my AMC 20 when it gets light out, will post in
an
> > hour or so.
>
> > "Deniz" <dhasi...@gmail.com> wrote in message
> >news:1175755955.763919.258190@p77g2000hsh.googleg roups.com...
> >> On 5 Nisan, 06:53, "L.W. \(Bill\) ------ III" <billhug...@***.net>
> >> wrote:
>
>
>>>http://www.4xshaft.com/driveline101....te4x4.com/tech...
> >>> God Bless America, Bill 0|||||||0
> >>> mailto:LW------...@aol.comhttp://www.----------.com/
>
> >>> "Deniz" <dhasi...@gmail.com> wrote in message
>
> >>>news:1175674679.158682.313630@d57g2000hsg.googl egroups.com...
>
> >>> > Hi guys,
> >>> > I'm from Turkey and i have 79 cj5. Recently i have replaced my amc
20
> >>> > with a dana 44. But some vibrations occured both while accelerating
> >>> > and decelerating probably because of the rear driveshaft.It's a bit
> >>> > difficult to find parts for cjs in Turkey, i need to have some parts
> >>> > made customly. Do i need a longer driveshaft as it looks slightly
> >>> > longer now the it used to be or should i try to have a cv type drive
> >>> > shaft custom made as i'm thinking of buying a 2 inch lift kit in the
> >>> > near future? With a cv drive shaft do i need transfer case lowering
> >>> > kit for 2 inch lift?
> >>> > Thank you all in advance,
> >>> > Deniz
>
> >>> --
> >>> Posted via a free Usenet account fromhttp://www.teranews.com
>
> >> First of all thank you all guys,
> >> I'll first check the angles, but i was quite carefull installing the
> >> shaft. The d44 i bought was a second hand one and it was in a very
> >> good condition, unfortunately without a drive shaft. To be honest i
> >> hadn't measured the housings. But by the look of the mud marks and
> >> clean parts of the shaft i can tell that it's standing a wee bit
> >> longer. I'll try to find an old jeep on the road and stop it and get
> >> under to measure the shaft unfortunately there arent't many of those.
> >> The cv shaft option is gonna have to wait till i get the lift kit as i
> >> understand that i need to change the angles of the spring perches and
> >> i don't want to take the the axle off again, i wanna drive it for a
> >> while as i'd been working on it for quite some time, i missed the
> >> little beasty. I'll replace the u joints as well once i measure a D44
> >> drive shaft. The u joints are a couple of years old but i hadn't
> >> maintained them regularly.
> >> Thank you all again.
>
> >> Deniz- Alıntıyı gizle -
>
> - Alıntıyı göster -
Thanks Greg,
I'll go an measure mine before it gets dark at this side of
Greenwich:)
Deniz
-----
If you drive it much with that vibration it will damage things.
Earle
news:1175785537.830895.197320@e65g2000hsc.googlegr oups.com...
On 5 Nisan, 17:39, "Greg" <gregl...@hotmail.com> wrote:
> Looks like 10 5/8", or 27 cm from center of axle tube to front face of
> housing, yoke not included.
>
> "Greg" <gregl...@hotmail.com> wrote in message
>
> news:bD6Rh.32235$DE1.13836@pd7urf2no...
>
>
>
> > I'll go out and measure my AMC 20 when it gets light out, will post in
an
> > hour or so.
>
> > "Deniz" <dhasi...@gmail.com> wrote in message
> >news:1175755955.763919.258190@p77g2000hsh.googleg roups.com...
> >> On 5 Nisan, 06:53, "L.W. \(Bill\) ------ III" <billhug...@***.net>
> >> wrote:
>
>
>>>http://www.4xshaft.com/driveline101....te4x4.com/tech...
> >>> God Bless America, Bill 0|||||||0
> >>> mailto:LW------...@aol.comhttp://www.----------.com/
>
> >>> "Deniz" <dhasi...@gmail.com> wrote in message
>
> >>>news:1175674679.158682.313630@d57g2000hsg.googl egroups.com...
>
> >>> > Hi guys,
> >>> > I'm from Turkey and i have 79 cj5. Recently i have replaced my amc
20
> >>> > with a dana 44. But some vibrations occured both while accelerating
> >>> > and decelerating probably because of the rear driveshaft.It's a bit
> >>> > difficult to find parts for cjs in Turkey, i need to have some parts
> >>> > made customly. Do i need a longer driveshaft as it looks slightly
> >>> > longer now the it used to be or should i try to have a cv type drive
> >>> > shaft custom made as i'm thinking of buying a 2 inch lift kit in the
> >>> > near future? With a cv drive shaft do i need transfer case lowering
> >>> > kit for 2 inch lift?
> >>> > Thank you all in advance,
> >>> > Deniz
>
> >>> --
> >>> Posted via a free Usenet account fromhttp://www.teranews.com
>
> >> First of all thank you all guys,
> >> I'll first check the angles, but i was quite carefull installing the
> >> shaft. The d44 i bought was a second hand one and it was in a very
> >> good condition, unfortunately without a drive shaft. To be honest i
> >> hadn't measured the housings. But by the look of the mud marks and
> >> clean parts of the shaft i can tell that it's standing a wee bit
> >> longer. I'll try to find an old jeep on the road and stop it and get
> >> under to measure the shaft unfortunately there arent't many of those.
> >> The cv shaft option is gonna have to wait till i get the lift kit as i
> >> understand that i need to change the angles of the spring perches and
> >> i don't want to take the the axle off again, i wanna drive it for a
> >> while as i'd been working on it for quite some time, i missed the
> >> little beasty. I'll replace the u joints as well once i measure a D44
> >> drive shaft. The u joints are a couple of years old but i hadn't
> >> maintained them regularly.
> >> Thank you all again.
>
> >> Deniz- Alıntıyı gizle -
>
> - Alıntıyı göster -
Thanks Greg,
I'll go an measure mine before it gets dark at this side of
Greenwich:)
Deniz
-----
If you drive it much with that vibration it will damage things.
Earle
Guest
Posts: n/a
Re: amc 20 dana 44 replacement
"Deniz" <dhasirci@gmail.com> wrote in message
news:1175785537.830895.197320@e65g2000hsc.googlegr oups.com...
On 5 Nisan, 17:39, "Greg" <gregl...@hotmail.com> wrote:
> Looks like 10 5/8", or 27 cm from center of axle tube to front face of
> housing, yoke not included.
>
> "Greg" <gregl...@hotmail.com> wrote in message
>
> news:bD6Rh.32235$DE1.13836@pd7urf2no...
>
>
>
> > I'll go out and measure my AMC 20 when it gets light out, will post in
an
> > hour or so.
>
> > "Deniz" <dhasi...@gmail.com> wrote in message
> >news:1175755955.763919.258190@p77g2000hsh.googleg roups.com...
> >> On 5 Nisan, 06:53, "L.W. \(Bill\) ------ III" <billhug...@***.net>
> >> wrote:
>
>
>>>http://www.4xshaft.com/driveline101....te4x4.com/tech...
> >>> God Bless America, Bill 0|||||||0
> >>> mailto:LW------...@aol.comhttp://www.----------.com/
>
> >>> "Deniz" <dhasi...@gmail.com> wrote in message
>
> >>>news:1175674679.158682.313630@d57g2000hsg.googl egroups.com...
>
> >>> > Hi guys,
> >>> > I'm from Turkey and i have 79 cj5. Recently i have replaced my amc
20
> >>> > with a dana 44. But some vibrations occured both while accelerating
> >>> > and decelerating probably because of the rear driveshaft.It's a bit
> >>> > difficult to find parts for cjs in Turkey, i need to have some parts
> >>> > made customly. Do i need a longer driveshaft as it looks slightly
> >>> > longer now the it used to be or should i try to have a cv type drive
> >>> > shaft custom made as i'm thinking of buying a 2 inch lift kit in the
> >>> > near future? With a cv drive shaft do i need transfer case lowering
> >>> > kit for 2 inch lift?
> >>> > Thank you all in advance,
> >>> > Deniz
>
> >>> --
> >>> Posted via a free Usenet account fromhttp://www.teranews.com
>
> >> First of all thank you all guys,
> >> I'll first check the angles, but i was quite carefull installing the
> >> shaft. The d44 i bought was a second hand one and it was in a very
> >> good condition, unfortunately without a drive shaft. To be honest i
> >> hadn't measured the housings. But by the look of the mud marks and
> >> clean parts of the shaft i can tell that it's standing a wee bit
> >> longer. I'll try to find an old jeep on the road and stop it and get
> >> under to measure the shaft unfortunately there arent't many of those.
> >> The cv shaft option is gonna have to wait till i get the lift kit as i
> >> understand that i need to change the angles of the spring perches and
> >> i don't want to take the the axle off again, i wanna drive it for a
> >> while as i'd been working on it for quite some time, i missed the
> >> little beasty. I'll replace the u joints as well once i measure a D44
> >> drive shaft. The u joints are a couple of years old but i hadn't
> >> maintained them regularly.
> >> Thank you all again.
>
> >> Deniz- Alıntıyı gizle -
>
> - Alıntıyı göster -
Thanks Greg,
I'll go an measure mine before it gets dark at this side of
Greenwich:)
Deniz
-----
If you drive it much with that vibration it will damage things.
Earle
news:1175785537.830895.197320@e65g2000hsc.googlegr oups.com...
On 5 Nisan, 17:39, "Greg" <gregl...@hotmail.com> wrote:
> Looks like 10 5/8", or 27 cm from center of axle tube to front face of
> housing, yoke not included.
>
> "Greg" <gregl...@hotmail.com> wrote in message
>
> news:bD6Rh.32235$DE1.13836@pd7urf2no...
>
>
>
> > I'll go out and measure my AMC 20 when it gets light out, will post in
an
> > hour or so.
>
> > "Deniz" <dhasi...@gmail.com> wrote in message
> >news:1175755955.763919.258190@p77g2000hsh.googleg roups.com...
> >> On 5 Nisan, 06:53, "L.W. \(Bill\) ------ III" <billhug...@***.net>
> >> wrote:
>
>
>>>http://www.4xshaft.com/driveline101....te4x4.com/tech...
> >>> God Bless America, Bill 0|||||||0
> >>> mailto:LW------...@aol.comhttp://www.----------.com/
>
> >>> "Deniz" <dhasi...@gmail.com> wrote in message
>
> >>>news:1175674679.158682.313630@d57g2000hsg.googl egroups.com...
>
> >>> > Hi guys,
> >>> > I'm from Turkey and i have 79 cj5. Recently i have replaced my amc
20
> >>> > with a dana 44. But some vibrations occured both while accelerating
> >>> > and decelerating probably because of the rear driveshaft.It's a bit
> >>> > difficult to find parts for cjs in Turkey, i need to have some parts
> >>> > made customly. Do i need a longer driveshaft as it looks slightly
> >>> > longer now the it used to be or should i try to have a cv type drive
> >>> > shaft custom made as i'm thinking of buying a 2 inch lift kit in the
> >>> > near future? With a cv drive shaft do i need transfer case lowering
> >>> > kit for 2 inch lift?
> >>> > Thank you all in advance,
> >>> > Deniz
>
> >>> --
> >>> Posted via a free Usenet account fromhttp://www.teranews.com
>
> >> First of all thank you all guys,
> >> I'll first check the angles, but i was quite carefull installing the
> >> shaft. The d44 i bought was a second hand one and it was in a very
> >> good condition, unfortunately without a drive shaft. To be honest i
> >> hadn't measured the housings. But by the look of the mud marks and
> >> clean parts of the shaft i can tell that it's standing a wee bit
> >> longer. I'll try to find an old jeep on the road and stop it and get
> >> under to measure the shaft unfortunately there arent't many of those.
> >> The cv shaft option is gonna have to wait till i get the lift kit as i
> >> understand that i need to change the angles of the spring perches and
> >> i don't want to take the the axle off again, i wanna drive it for a
> >> while as i'd been working on it for quite some time, i missed the
> >> little beasty. I'll replace the u joints as well once i measure a D44
> >> drive shaft. The u joints are a couple of years old but i hadn't
> >> maintained them regularly.
> >> Thank you all again.
>
> >> Deniz- Alıntıyı gizle -
>
> - Alıntıyı göster -
Thanks Greg,
I'll go an measure mine before it gets dark at this side of
Greenwich:)
Deniz
-----
If you drive it much with that vibration it will damage things.
Earle