AMC 150 too rich
05-11-2004, 11:01 AM
#11
Guest
Posts: n/a
Re: AMC 150 too rich
The stepper motor controls the air bypass only on the Carter BBD carb.
This means full rich is pins all the way in.
I highly doubt you have a Carter BBD on a 4 banger though....
You should check to see what it is. They all are manually tuneable with
'hidden' mix screrws the same as the non electronic ones, but it is hard
to point you the right direction not being sure of the carb...
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Chip wrote:
>
> The computer was not functioning so the stepper motor was inoperable (or at
> least was not being run by the bad computer) Before the bypass was
> complete, my father started the motor, it ran terrible until he uplugged the
> stepper motor, then it ran smooth. How can you tell where the stepper motor
> should be and how do you get it there if it is in the wrong place, which it
> obviously is because of the amount of gas running through it.
>
> Short of solving this carb trouble, what kind of pre-83 carb will fit the
> 150 engine?
>
> Thanks again,
>
> Chip
>
> "serg" <sfonNOSPAM@yahoo.com> wrote in message
> news:2gad30Fiu7bU1@uni-berlin.de...
> > did u make sure the stepper motor was in the right position before turning
> > it off? i never did the nutter bypass in mine before i took it off but i
> > remember you had to have the motor in a certain position before cutting
> the
> > wire. is your 02 sensor alive?
> >
> > "Chip" <cjenkins1@nospam.neo.rr.com> wrote in message
> > news:oRSnc.1090$OE3.804@fe1.columbus.rr.com...
> > > I have a question concerning an '84 CJ with the AMC 150 4 cyl engine and
> > one
> > > of those terrible Carter carburetors with a Nutter bypass performed.
> Keep
> > > in mind with this question that the catalytic converter needs to be
> > replaced
> > > and another one is on order. Here's the present trouble: The stepper
> > motor,
> > > which I believe controls the amount of fuel, has been disconnected as
> part
> > > of the bypass. The gas to air ratio is too rich and there is really no
> way
> > > to adjust it, or so I'm told. I'm not sure how much the catalytic
> > converter
> > > has to do with this but, how can the fuel mixture be adjusted with the
> > > bypass in place?
> > >
> > >
> > >
> > > Thanks,
> > >
> > > Chip
> > >
> > >
> > >
> > >
> > >
> > >
> >
> >
This means full rich is pins all the way in.
I highly doubt you have a Carter BBD on a 4 banger though....
You should check to see what it is. They all are manually tuneable with
'hidden' mix screrws the same as the non electronic ones, but it is hard
to point you the right direction not being sure of the carb...
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Chip wrote:
>
> The computer was not functioning so the stepper motor was inoperable (or at
> least was not being run by the bad computer) Before the bypass was
> complete, my father started the motor, it ran terrible until he uplugged the
> stepper motor, then it ran smooth. How can you tell where the stepper motor
> should be and how do you get it there if it is in the wrong place, which it
> obviously is because of the amount of gas running through it.
>
> Short of solving this carb trouble, what kind of pre-83 carb will fit the
> 150 engine?
>
> Thanks again,
>
> Chip
>
> "serg" <sfonNOSPAM@yahoo.com> wrote in message
> news:2gad30Fiu7bU1@uni-berlin.de...
> > did u make sure the stepper motor was in the right position before turning
> > it off? i never did the nutter bypass in mine before i took it off but i
> > remember you had to have the motor in a certain position before cutting
> the
> > wire. is your 02 sensor alive?
> >
> > "Chip" <cjenkins1@nospam.neo.rr.com> wrote in message
> > news:oRSnc.1090$OE3.804@fe1.columbus.rr.com...
> > > I have a question concerning an '84 CJ with the AMC 150 4 cyl engine and
> > one
> > > of those terrible Carter carburetors with a Nutter bypass performed.
> Keep
> > > in mind with this question that the catalytic converter needs to be
> > replaced
> > > and another one is on order. Here's the present trouble: The stepper
> > motor,
> > > which I believe controls the amount of fuel, has been disconnected as
> part
> > > of the bypass. The gas to air ratio is too rich and there is really no
> way
> > > to adjust it, or so I'm told. I'm not sure how much the catalytic
> > converter
> > > has to do with this but, how can the fuel mixture be adjusted with the
> > > bypass in place?
> > >
> > >
> > >
> > > Thanks,
> > >
> > > Chip
> > >
> > >
> > >
> > >
> > >
> > >
> >
> >
05-11-2004, 11:01 AM
#12
Guest
Posts: n/a
Re: AMC 150 too rich
The stepper motor controls the air bypass only on the Carter BBD carb.
This means full rich is pins all the way in.
I highly doubt you have a Carter BBD on a 4 banger though....
You should check to see what it is. They all are manually tuneable with
'hidden' mix screrws the same as the non electronic ones, but it is hard
to point you the right direction not being sure of the carb...
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Chip wrote:
>
> The computer was not functioning so the stepper motor was inoperable (or at
> least was not being run by the bad computer) Before the bypass was
> complete, my father started the motor, it ran terrible until he uplugged the
> stepper motor, then it ran smooth. How can you tell where the stepper motor
> should be and how do you get it there if it is in the wrong place, which it
> obviously is because of the amount of gas running through it.
>
> Short of solving this carb trouble, what kind of pre-83 carb will fit the
> 150 engine?
>
> Thanks again,
>
> Chip
>
> "serg" <sfonNOSPAM@yahoo.com> wrote in message
> news:2gad30Fiu7bU1@uni-berlin.de...
> > did u make sure the stepper motor was in the right position before turning
> > it off? i never did the nutter bypass in mine before i took it off but i
> > remember you had to have the motor in a certain position before cutting
> the
> > wire. is your 02 sensor alive?
> >
> > "Chip" <cjenkins1@nospam.neo.rr.com> wrote in message
> > news:oRSnc.1090$OE3.804@fe1.columbus.rr.com...
> > > I have a question concerning an '84 CJ with the AMC 150 4 cyl engine and
> > one
> > > of those terrible Carter carburetors with a Nutter bypass performed.
> Keep
> > > in mind with this question that the catalytic converter needs to be
> > replaced
> > > and another one is on order. Here's the present trouble: The stepper
> > motor,
> > > which I believe controls the amount of fuel, has been disconnected as
> part
> > > of the bypass. The gas to air ratio is too rich and there is really no
> way
> > > to adjust it, or so I'm told. I'm not sure how much the catalytic
> > converter
> > > has to do with this but, how can the fuel mixture be adjusted with the
> > > bypass in place?
> > >
> > >
> > >
> > > Thanks,
> > >
> > > Chip
> > >
> > >
> > >
> > >
> > >
> > >
> >
> >
This means full rich is pins all the way in.
I highly doubt you have a Carter BBD on a 4 banger though....
You should check to see what it is. They all are manually tuneable with
'hidden' mix screrws the same as the non electronic ones, but it is hard
to point you the right direction not being sure of the carb...
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Chip wrote:
>
> The computer was not functioning so the stepper motor was inoperable (or at
> least was not being run by the bad computer) Before the bypass was
> complete, my father started the motor, it ran terrible until he uplugged the
> stepper motor, then it ran smooth. How can you tell where the stepper motor
> should be and how do you get it there if it is in the wrong place, which it
> obviously is because of the amount of gas running through it.
>
> Short of solving this carb trouble, what kind of pre-83 carb will fit the
> 150 engine?
>
> Thanks again,
>
> Chip
>
> "serg" <sfonNOSPAM@yahoo.com> wrote in message
> news:2gad30Fiu7bU1@uni-berlin.de...
> > did u make sure the stepper motor was in the right position before turning
> > it off? i never did the nutter bypass in mine before i took it off but i
> > remember you had to have the motor in a certain position before cutting
> the
> > wire. is your 02 sensor alive?
> >
> > "Chip" <cjenkins1@nospam.neo.rr.com> wrote in message
> > news:oRSnc.1090$OE3.804@fe1.columbus.rr.com...
> > > I have a question concerning an '84 CJ with the AMC 150 4 cyl engine and
> > one
> > > of those terrible Carter carburetors with a Nutter bypass performed.
> Keep
> > > in mind with this question that the catalytic converter needs to be
> > replaced
> > > and another one is on order. Here's the present trouble: The stepper
> > motor,
> > > which I believe controls the amount of fuel, has been disconnected as
> part
> > > of the bypass. The gas to air ratio is too rich and there is really no
> way
> > > to adjust it, or so I'm told. I'm not sure how much the catalytic
> > converter
> > > has to do with this but, how can the fuel mixture be adjusted with the
> > > bypass in place?
> > >
> > >
> > >
> > > Thanks,
> > >
> > > Chip
> > >
> > >
> > >
> > >
> > >
> > >
> >
> >
05-11-2004, 11:01 AM
#13
Guest
Posts: n/a
Re: AMC 150 too rich
The stepper motor controls the air bypass only on the Carter BBD carb.
This means full rich is pins all the way in.
I highly doubt you have a Carter BBD on a 4 banger though....
You should check to see what it is. They all are manually tuneable with
'hidden' mix screrws the same as the non electronic ones, but it is hard
to point you the right direction not being sure of the carb...
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Chip wrote:
>
> The computer was not functioning so the stepper motor was inoperable (or at
> least was not being run by the bad computer) Before the bypass was
> complete, my father started the motor, it ran terrible until he uplugged the
> stepper motor, then it ran smooth. How can you tell where the stepper motor
> should be and how do you get it there if it is in the wrong place, which it
> obviously is because of the amount of gas running through it.
>
> Short of solving this carb trouble, what kind of pre-83 carb will fit the
> 150 engine?
>
> Thanks again,
>
> Chip
>
> "serg" <sfonNOSPAM@yahoo.com> wrote in message
> news:2gad30Fiu7bU1@uni-berlin.de...
> > did u make sure the stepper motor was in the right position before turning
> > it off? i never did the nutter bypass in mine before i took it off but i
> > remember you had to have the motor in a certain position before cutting
> the
> > wire. is your 02 sensor alive?
> >
> > "Chip" <cjenkins1@nospam.neo.rr.com> wrote in message
> > news:oRSnc.1090$OE3.804@fe1.columbus.rr.com...
> > > I have a question concerning an '84 CJ with the AMC 150 4 cyl engine and
> > one
> > > of those terrible Carter carburetors with a Nutter bypass performed.
> Keep
> > > in mind with this question that the catalytic converter needs to be
> > replaced
> > > and another one is on order. Here's the present trouble: The stepper
> > motor,
> > > which I believe controls the amount of fuel, has been disconnected as
> part
> > > of the bypass. The gas to air ratio is too rich and there is really no
> way
> > > to adjust it, or so I'm told. I'm not sure how much the catalytic
> > converter
> > > has to do with this but, how can the fuel mixture be adjusted with the
> > > bypass in place?
> > >
> > >
> > >
> > > Thanks,
> > >
> > > Chip
> > >
> > >
> > >
> > >
> > >
> > >
> >
> >
This means full rich is pins all the way in.
I highly doubt you have a Carter BBD on a 4 banger though....
You should check to see what it is. They all are manually tuneable with
'hidden' mix screrws the same as the non electronic ones, but it is hard
to point you the right direction not being sure of the carb...
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Chip wrote:
>
> The computer was not functioning so the stepper motor was inoperable (or at
> least was not being run by the bad computer) Before the bypass was
> complete, my father started the motor, it ran terrible until he uplugged the
> stepper motor, then it ran smooth. How can you tell where the stepper motor
> should be and how do you get it there if it is in the wrong place, which it
> obviously is because of the amount of gas running through it.
>
> Short of solving this carb trouble, what kind of pre-83 carb will fit the
> 150 engine?
>
> Thanks again,
>
> Chip
>
> "serg" <sfonNOSPAM@yahoo.com> wrote in message
> news:2gad30Fiu7bU1@uni-berlin.de...
> > did u make sure the stepper motor was in the right position before turning
> > it off? i never did the nutter bypass in mine before i took it off but i
> > remember you had to have the motor in a certain position before cutting
> the
> > wire. is your 02 sensor alive?
> >
> > "Chip" <cjenkins1@nospam.neo.rr.com> wrote in message
> > news:oRSnc.1090$OE3.804@fe1.columbus.rr.com...
> > > I have a question concerning an '84 CJ with the AMC 150 4 cyl engine and
> > one
> > > of those terrible Carter carburetors with a Nutter bypass performed.
> Keep
> > > in mind with this question that the catalytic converter needs to be
> > replaced
> > > and another one is on order. Here's the present trouble: The stepper
> > motor,
> > > which I believe controls the amount of fuel, has been disconnected as
> part
> > > of the bypass. The gas to air ratio is too rich and there is really no
> way
> > > to adjust it, or so I'm told. I'm not sure how much the catalytic
> > converter
> > > has to do with this but, how can the fuel mixture be adjusted with the
> > > bypass in place?
> > >
> > >
> > >
> > > Thanks,
> > >
> > > Chip
> > >
> > >
> > >
> > >
> > >
> > >
> >
> >
05-12-2004, 11:56 AM
#14
Guest
Posts: n/a
Re: AMC 150 too rich
Ok, you have the YFA carb.
The fact that it runs pretty decent with the stepper unplugged would
lead me to believe the mix is at least 'close' by default.
The YFA with the stepper still has the manual mix screw, same as the
BBD. They hide it under a metal plug in the base plate of the carb.
Some you can pull the blocking plug out with a point, others have to be
drilled and pried out.
If you set the carb with the throttle lever in front of you, the mix
screw will be in the base to your right under the plug likely.
I would highly recommend you get the Haynes CJ manual. It has a great
section on the carbs.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Chip wrote:
>
> The computer was not functioning so the stepper motor was inoperable (or at
> least was not being run by the bad computer) Before the bypass was
> complete, my father started the motor, it ran terrible until he uplugged the
> stepper motor, then it ran smooth. How can you tell where the stepper motor
> should be and how do you get it there if it is in the wrong place, which it
> obviously is because of the amount of gas running through it.
>
> Short of solving this carb trouble, what kind of pre-83 carb will fit the
> 150 engine?
>
> Thanks again,
>
> Chip
>
> "serg" <sfonNOSPAM@yahoo.com> wrote in message
> news:2gad30Fiu7bU1@uni-berlin.de...
> > did u make sure the stepper motor was in the right position before turning
> > it off? i never did the nutter bypass in mine before i took it off but i
> > remember you had to have the motor in a certain position before cutting
> the
> > wire. is your 02 sensor alive?
> >
> > "Chip" <cjenkins1@nospam.neo.rr.com> wrote in message
> > news:oRSnc.1090$OE3.804@fe1.columbus.rr.com...
> > > I have a question concerning an '84 CJ with the AMC 150 4 cyl engine and
> > one
> > > of those terrible Carter carburetors with a Nutter bypass performed.
> Keep
> > > in mind with this question that the catalytic converter needs to be
> > replaced
> > > and another one is on order. Here's the present trouble: The stepper
> > motor,
> > > which I believe controls the amount of fuel, has been disconnected as
> part
> > > of the bypass. The gas to air ratio is too rich and there is really no
> way
> > > to adjust it, or so I'm told. I'm not sure how much the catalytic
> > converter
> > > has to do with this but, how can the fuel mixture be adjusted with the
> > > bypass in place?
> > >
> > >
> > >
> > > Thanks,
> > >
> > > Chip
> > >
> > >
> > >
> > >
> > >
> > >
> >
> >
The fact that it runs pretty decent with the stepper unplugged would
lead me to believe the mix is at least 'close' by default.
The YFA with the stepper still has the manual mix screw, same as the
BBD. They hide it under a metal plug in the base plate of the carb.
Some you can pull the blocking plug out with a point, others have to be
drilled and pried out.
If you set the carb with the throttle lever in front of you, the mix
screw will be in the base to your right under the plug likely.
I would highly recommend you get the Haynes CJ manual. It has a great
section on the carbs.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Chip wrote:
>
> The computer was not functioning so the stepper motor was inoperable (or at
> least was not being run by the bad computer) Before the bypass was
> complete, my father started the motor, it ran terrible until he uplugged the
> stepper motor, then it ran smooth. How can you tell where the stepper motor
> should be and how do you get it there if it is in the wrong place, which it
> obviously is because of the amount of gas running through it.
>
> Short of solving this carb trouble, what kind of pre-83 carb will fit the
> 150 engine?
>
> Thanks again,
>
> Chip
>
> "serg" <sfonNOSPAM@yahoo.com> wrote in message
> news:2gad30Fiu7bU1@uni-berlin.de...
> > did u make sure the stepper motor was in the right position before turning
> > it off? i never did the nutter bypass in mine before i took it off but i
> > remember you had to have the motor in a certain position before cutting
> the
> > wire. is your 02 sensor alive?
> >
> > "Chip" <cjenkins1@nospam.neo.rr.com> wrote in message
> > news:oRSnc.1090$OE3.804@fe1.columbus.rr.com...
> > > I have a question concerning an '84 CJ with the AMC 150 4 cyl engine and
> > one
> > > of those terrible Carter carburetors with a Nutter bypass performed.
> Keep
> > > in mind with this question that the catalytic converter needs to be
> > replaced
> > > and another one is on order. Here's the present trouble: The stepper
> > motor,
> > > which I believe controls the amount of fuel, has been disconnected as
> part
> > > of the bypass. The gas to air ratio is too rich and there is really no
> way
> > > to adjust it, or so I'm told. I'm not sure how much the catalytic
> > converter
> > > has to do with this but, how can the fuel mixture be adjusted with the
> > > bypass in place?
> > >
> > >
> > >
> > > Thanks,
> > >
> > > Chip
> > >
> > >
> > >
> > >
> > >
> > >
> >
> >
05-12-2004, 11:56 AM
#15
Guest
Posts: n/a
Re: AMC 150 too rich
Ok, you have the YFA carb.
The fact that it runs pretty decent with the stepper unplugged would
lead me to believe the mix is at least 'close' by default.
The YFA with the stepper still has the manual mix screw, same as the
BBD. They hide it under a metal plug in the base plate of the carb.
Some you can pull the blocking plug out with a point, others have to be
drilled and pried out.
If you set the carb with the throttle lever in front of you, the mix
screw will be in the base to your right under the plug likely.
I would highly recommend you get the Haynes CJ manual. It has a great
section on the carbs.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Chip wrote:
>
> The computer was not functioning so the stepper motor was inoperable (or at
> least was not being run by the bad computer) Before the bypass was
> complete, my father started the motor, it ran terrible until he uplugged the
> stepper motor, then it ran smooth. How can you tell where the stepper motor
> should be and how do you get it there if it is in the wrong place, which it
> obviously is because of the amount of gas running through it.
>
> Short of solving this carb trouble, what kind of pre-83 carb will fit the
> 150 engine?
>
> Thanks again,
>
> Chip
>
> "serg" <sfonNOSPAM@yahoo.com> wrote in message
> news:2gad30Fiu7bU1@uni-berlin.de...
> > did u make sure the stepper motor was in the right position before turning
> > it off? i never did the nutter bypass in mine before i took it off but i
> > remember you had to have the motor in a certain position before cutting
> the
> > wire. is your 02 sensor alive?
> >
> > "Chip" <cjenkins1@nospam.neo.rr.com> wrote in message
> > news:oRSnc.1090$OE3.804@fe1.columbus.rr.com...
> > > I have a question concerning an '84 CJ with the AMC 150 4 cyl engine and
> > one
> > > of those terrible Carter carburetors with a Nutter bypass performed.
> Keep
> > > in mind with this question that the catalytic converter needs to be
> > replaced
> > > and another one is on order. Here's the present trouble: The stepper
> > motor,
> > > which I believe controls the amount of fuel, has been disconnected as
> part
> > > of the bypass. The gas to air ratio is too rich and there is really no
> way
> > > to adjust it, or so I'm told. I'm not sure how much the catalytic
> > converter
> > > has to do with this but, how can the fuel mixture be adjusted with the
> > > bypass in place?
> > >
> > >
> > >
> > > Thanks,
> > >
> > > Chip
> > >
> > >
> > >
> > >
> > >
> > >
> >
> >
The fact that it runs pretty decent with the stepper unplugged would
lead me to believe the mix is at least 'close' by default.
The YFA with the stepper still has the manual mix screw, same as the
BBD. They hide it under a metal plug in the base plate of the carb.
Some you can pull the blocking plug out with a point, others have to be
drilled and pried out.
If you set the carb with the throttle lever in front of you, the mix
screw will be in the base to your right under the plug likely.
I would highly recommend you get the Haynes CJ manual. It has a great
section on the carbs.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Chip wrote:
>
> The computer was not functioning so the stepper motor was inoperable (or at
> least was not being run by the bad computer) Before the bypass was
> complete, my father started the motor, it ran terrible until he uplugged the
> stepper motor, then it ran smooth. How can you tell where the stepper motor
> should be and how do you get it there if it is in the wrong place, which it
> obviously is because of the amount of gas running through it.
>
> Short of solving this carb trouble, what kind of pre-83 carb will fit the
> 150 engine?
>
> Thanks again,
>
> Chip
>
> "serg" <sfonNOSPAM@yahoo.com> wrote in message
> news:2gad30Fiu7bU1@uni-berlin.de...
> > did u make sure the stepper motor was in the right position before turning
> > it off? i never did the nutter bypass in mine before i took it off but i
> > remember you had to have the motor in a certain position before cutting
> the
> > wire. is your 02 sensor alive?
> >
> > "Chip" <cjenkins1@nospam.neo.rr.com> wrote in message
> > news:oRSnc.1090$OE3.804@fe1.columbus.rr.com...
> > > I have a question concerning an '84 CJ with the AMC 150 4 cyl engine and
> > one
> > > of those terrible Carter carburetors with a Nutter bypass performed.
> Keep
> > > in mind with this question that the catalytic converter needs to be
> > replaced
> > > and another one is on order. Here's the present trouble: The stepper
> > motor,
> > > which I believe controls the amount of fuel, has been disconnected as
> part
> > > of the bypass. The gas to air ratio is too rich and there is really no
> way
> > > to adjust it, or so I'm told. I'm not sure how much the catalytic
> > converter
> > > has to do with this but, how can the fuel mixture be adjusted with the
> > > bypass in place?
> > >
> > >
> > >
> > > Thanks,
> > >
> > > Chip
> > >
> > >
> > >
> > >
> > >
> > >
> >
> >
05-12-2004, 11:56 AM
#16
Guest
Posts: n/a
Re: AMC 150 too rich
Ok, you have the YFA carb.
The fact that it runs pretty decent with the stepper unplugged would
lead me to believe the mix is at least 'close' by default.
The YFA with the stepper still has the manual mix screw, same as the
BBD. They hide it under a metal plug in the base plate of the carb.
Some you can pull the blocking plug out with a point, others have to be
drilled and pried out.
If you set the carb with the throttle lever in front of you, the mix
screw will be in the base to your right under the plug likely.
I would highly recommend you get the Haynes CJ manual. It has a great
section on the carbs.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Chip wrote:
>
> The computer was not functioning so the stepper motor was inoperable (or at
> least was not being run by the bad computer) Before the bypass was
> complete, my father started the motor, it ran terrible until he uplugged the
> stepper motor, then it ran smooth. How can you tell where the stepper motor
> should be and how do you get it there if it is in the wrong place, which it
> obviously is because of the amount of gas running through it.
>
> Short of solving this carb trouble, what kind of pre-83 carb will fit the
> 150 engine?
>
> Thanks again,
>
> Chip
>
> "serg" <sfonNOSPAM@yahoo.com> wrote in message
> news:2gad30Fiu7bU1@uni-berlin.de...
> > did u make sure the stepper motor was in the right position before turning
> > it off? i never did the nutter bypass in mine before i took it off but i
> > remember you had to have the motor in a certain position before cutting
> the
> > wire. is your 02 sensor alive?
> >
> > "Chip" <cjenkins1@nospam.neo.rr.com> wrote in message
> > news:oRSnc.1090$OE3.804@fe1.columbus.rr.com...
> > > I have a question concerning an '84 CJ with the AMC 150 4 cyl engine and
> > one
> > > of those terrible Carter carburetors with a Nutter bypass performed.
> Keep
> > > in mind with this question that the catalytic converter needs to be
> > replaced
> > > and another one is on order. Here's the present trouble: The stepper
> > motor,
> > > which I believe controls the amount of fuel, has been disconnected as
> part
> > > of the bypass. The gas to air ratio is too rich and there is really no
> way
> > > to adjust it, or so I'm told. I'm not sure how much the catalytic
> > converter
> > > has to do with this but, how can the fuel mixture be adjusted with the
> > > bypass in place?
> > >
> > >
> > >
> > > Thanks,
> > >
> > > Chip
> > >
> > >
> > >
> > >
> > >
> > >
> >
> >
The fact that it runs pretty decent with the stepper unplugged would
lead me to believe the mix is at least 'close' by default.
The YFA with the stepper still has the manual mix screw, same as the
BBD. They hide it under a metal plug in the base plate of the carb.
Some you can pull the blocking plug out with a point, others have to be
drilled and pried out.
If you set the carb with the throttle lever in front of you, the mix
screw will be in the base to your right under the plug likely.
I would highly recommend you get the Haynes CJ manual. It has a great
section on the carbs.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Chip wrote:
>
> The computer was not functioning so the stepper motor was inoperable (or at
> least was not being run by the bad computer) Before the bypass was
> complete, my father started the motor, it ran terrible until he uplugged the
> stepper motor, then it ran smooth. How can you tell where the stepper motor
> should be and how do you get it there if it is in the wrong place, which it
> obviously is because of the amount of gas running through it.
>
> Short of solving this carb trouble, what kind of pre-83 carb will fit the
> 150 engine?
>
> Thanks again,
>
> Chip
>
> "serg" <sfonNOSPAM@yahoo.com> wrote in message
> news:2gad30Fiu7bU1@uni-berlin.de...
> > did u make sure the stepper motor was in the right position before turning
> > it off? i never did the nutter bypass in mine before i took it off but i
> > remember you had to have the motor in a certain position before cutting
> the
> > wire. is your 02 sensor alive?
> >
> > "Chip" <cjenkins1@nospam.neo.rr.com> wrote in message
> > news:oRSnc.1090$OE3.804@fe1.columbus.rr.com...
> > > I have a question concerning an '84 CJ with the AMC 150 4 cyl engine and
> > one
> > > of those terrible Carter carburetors with a Nutter bypass performed.
> Keep
> > > in mind with this question that the catalytic converter needs to be
> > replaced
> > > and another one is on order. Here's the present trouble: The stepper
> > motor,
> > > which I believe controls the amount of fuel, has been disconnected as
> part
> > > of the bypass. The gas to air ratio is too rich and there is really no
> way
> > > to adjust it, or so I'm told. I'm not sure how much the catalytic
> > converter
> > > has to do with this but, how can the fuel mixture be adjusted with the
> > > bypass in place?
> > >
> > >
> > >
> > > Thanks,
> > >
> > > Chip
> > >
> > >
> > >
> > >
> > >
> > >
> >
> >
05-12-2004, 11:56 AM
#17
Guest
Posts: n/a
Re: AMC 150 too rich
Ok, you have the YFA carb.
The fact that it runs pretty decent with the stepper unplugged would
lead me to believe the mix is at least 'close' by default.
The YFA with the stepper still has the manual mix screw, same as the
BBD. They hide it under a metal plug in the base plate of the carb.
Some you can pull the blocking plug out with a point, others have to be
drilled and pried out.
If you set the carb with the throttle lever in front of you, the mix
screw will be in the base to your right under the plug likely.
I would highly recommend you get the Haynes CJ manual. It has a great
section on the carbs.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Chip wrote:
>
> The computer was not functioning so the stepper motor was inoperable (or at
> least was not being run by the bad computer) Before the bypass was
> complete, my father started the motor, it ran terrible until he uplugged the
> stepper motor, then it ran smooth. How can you tell where the stepper motor
> should be and how do you get it there if it is in the wrong place, which it
> obviously is because of the amount of gas running through it.
>
> Short of solving this carb trouble, what kind of pre-83 carb will fit the
> 150 engine?
>
> Thanks again,
>
> Chip
>
> "serg" <sfonNOSPAM@yahoo.com> wrote in message
> news:2gad30Fiu7bU1@uni-berlin.de...
> > did u make sure the stepper motor was in the right position before turning
> > it off? i never did the nutter bypass in mine before i took it off but i
> > remember you had to have the motor in a certain position before cutting
> the
> > wire. is your 02 sensor alive?
> >
> > "Chip" <cjenkins1@nospam.neo.rr.com> wrote in message
> > news:oRSnc.1090$OE3.804@fe1.columbus.rr.com...
> > > I have a question concerning an '84 CJ with the AMC 150 4 cyl engine and
> > one
> > > of those terrible Carter carburetors with a Nutter bypass performed.
> Keep
> > > in mind with this question that the catalytic converter needs to be
> > replaced
> > > and another one is on order. Here's the present trouble: The stepper
> > motor,
> > > which I believe controls the amount of fuel, has been disconnected as
> part
> > > of the bypass. The gas to air ratio is too rich and there is really no
> way
> > > to adjust it, or so I'm told. I'm not sure how much the catalytic
> > converter
> > > has to do with this but, how can the fuel mixture be adjusted with the
> > > bypass in place?
> > >
> > >
> > >
> > > Thanks,
> > >
> > > Chip
> > >
> > >
> > >
> > >
> > >
> > >
> >
> >
The fact that it runs pretty decent with the stepper unplugged would
lead me to believe the mix is at least 'close' by default.
The YFA with the stepper still has the manual mix screw, same as the
BBD. They hide it under a metal plug in the base plate of the carb.
Some you can pull the blocking plug out with a point, others have to be
drilled and pried out.
If you set the carb with the throttle lever in front of you, the mix
screw will be in the base to your right under the plug likely.
I would highly recommend you get the Haynes CJ manual. It has a great
section on the carbs.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Chip wrote:
>
> The computer was not functioning so the stepper motor was inoperable (or at
> least was not being run by the bad computer) Before the bypass was
> complete, my father started the motor, it ran terrible until he uplugged the
> stepper motor, then it ran smooth. How can you tell where the stepper motor
> should be and how do you get it there if it is in the wrong place, which it
> obviously is because of the amount of gas running through it.
>
> Short of solving this carb trouble, what kind of pre-83 carb will fit the
> 150 engine?
>
> Thanks again,
>
> Chip
>
> "serg" <sfonNOSPAM@yahoo.com> wrote in message
> news:2gad30Fiu7bU1@uni-berlin.de...
> > did u make sure the stepper motor was in the right position before turning
> > it off? i never did the nutter bypass in mine before i took it off but i
> > remember you had to have the motor in a certain position before cutting
> the
> > wire. is your 02 sensor alive?
> >
> > "Chip" <cjenkins1@nospam.neo.rr.com> wrote in message
> > news:oRSnc.1090$OE3.804@fe1.columbus.rr.com...
> > > I have a question concerning an '84 CJ with the AMC 150 4 cyl engine and
> > one
> > > of those terrible Carter carburetors with a Nutter bypass performed.
> Keep
> > > in mind with this question that the catalytic converter needs to be
> > replaced
> > > and another one is on order. Here's the present trouble: The stepper
> > motor,
> > > which I believe controls the amount of fuel, has been disconnected as
> part
> > > of the bypass. The gas to air ratio is too rich and there is really no
> way
> > > to adjust it, or so I'm told. I'm not sure how much the catalytic
> > converter
> > > has to do with this but, how can the fuel mixture be adjusted with the
> > > bypass in place?
> > >
> > >
> > >
> > > Thanks,
> > >
> > > Chip
> > >
> > >
> > >
> > >
> > >
> > >
> >
> >
05-12-2004, 01:28 PM
#18
Guest
Posts: n/a
Re: AMC 150 too rich
ditto.
:)
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:40A24910.4395B719@sympatico.ca...
> Ok, you have the YFA carb.
>
> The fact that it runs pretty decent with the stepper unplugged would
> lead me to believe the mix is at least 'close' by default.
>
> The YFA with the stepper still has the manual mix screw, same as the
> BBD. They hide it under a metal plug in the base plate of the carb.
> Some you can pull the blocking plug out with a point, others have to be
> drilled and pried out.
>
> If you set the carb with the throttle lever in front of you, the mix
> screw will be in the base to your right under the plug likely.
>
> I would highly recommend you get the Haynes CJ manual. It has a great
> section on the carbs.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Chip wrote:
> >
> > The computer was not functioning so the stepper motor was inoperable (or
at
> > least was not being run by the bad computer) Before the bypass was
> > complete, my father started the motor, it ran terrible until he uplugged
the
> > stepper motor, then it ran smooth. How can you tell where the stepper
motor
> > should be and how do you get it there if it is in the wrong place, which
it
> > obviously is because of the amount of gas running through it.
> >
> > Short of solving this carb trouble, what kind of pre-83 carb will fit
the
> > 150 engine?
> >
> > Thanks again,
> >
> > Chip
> >
> > "serg" <sfonNOSPAM@yahoo.com> wrote in message
> > news:2gad30Fiu7bU1@uni-berlin.de...
> > > did u make sure the stepper motor was in the right position before
turning
> > > it off? i never did the nutter bypass in mine before i took it off but
i
> > > remember you had to have the motor in a certain position before
cutting
> > the
> > > wire. is your 02 sensor alive?
> > >
> > > "Chip" <cjenkins1@nospam.neo.rr.com> wrote in message
> > > news:oRSnc.1090$OE3.804@fe1.columbus.rr.com...
> > > > I have a question concerning an '84 CJ with the AMC 150 4 cyl engine
and
> > > one
> > > > of those terrible Carter carburetors with a Nutter bypass performed.
> > Keep
> > > > in mind with this question that the catalytic converter needs to be
> > > replaced
> > > > and another one is on order. Here's the present trouble: The stepper
> > > motor,
> > > > which I believe controls the amount of fuel, has been disconnected
as
> > part
> > > > of the bypass. The gas to air ratio is too rich and there is really
no
> > way
> > > > to adjust it, or so I'm told. I'm not sure how much the catalytic
> > > converter
> > > > has to do with this but, how can the fuel mixture be adjusted with
the
> > > > bypass in place?
> > > >
> > > >
> > > >
> > > > Thanks,
> > > >
> > > > Chip
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > >
> > >
:)
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:40A24910.4395B719@sympatico.ca...
> Ok, you have the YFA carb.
>
> The fact that it runs pretty decent with the stepper unplugged would
> lead me to believe the mix is at least 'close' by default.
>
> The YFA with the stepper still has the manual mix screw, same as the
> BBD. They hide it under a metal plug in the base plate of the carb.
> Some you can pull the blocking plug out with a point, others have to be
> drilled and pried out.
>
> If you set the carb with the throttle lever in front of you, the mix
> screw will be in the base to your right under the plug likely.
>
> I would highly recommend you get the Haynes CJ manual. It has a great
> section on the carbs.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Chip wrote:
> >
> > The computer was not functioning so the stepper motor was inoperable (or
at
> > least was not being run by the bad computer) Before the bypass was
> > complete, my father started the motor, it ran terrible until he uplugged
the
> > stepper motor, then it ran smooth. How can you tell where the stepper
motor
> > should be and how do you get it there if it is in the wrong place, which
it
> > obviously is because of the amount of gas running through it.
> >
> > Short of solving this carb trouble, what kind of pre-83 carb will fit
the
> > 150 engine?
> >
> > Thanks again,
> >
> > Chip
> >
> > "serg" <sfonNOSPAM@yahoo.com> wrote in message
> > news:2gad30Fiu7bU1@uni-berlin.de...
> > > did u make sure the stepper motor was in the right position before
turning
> > > it off? i never did the nutter bypass in mine before i took it off but
i
> > > remember you had to have the motor in a certain position before
cutting
> > the
> > > wire. is your 02 sensor alive?
> > >
> > > "Chip" <cjenkins1@nospam.neo.rr.com> wrote in message
> > > news:oRSnc.1090$OE3.804@fe1.columbus.rr.com...
> > > > I have a question concerning an '84 CJ with the AMC 150 4 cyl engine
and
> > > one
> > > > of those terrible Carter carburetors with a Nutter bypass performed.
> > Keep
> > > > in mind with this question that the catalytic converter needs to be
> > > replaced
> > > > and another one is on order. Here's the present trouble: The stepper
> > > motor,
> > > > which I believe controls the amount of fuel, has been disconnected
as
> > part
> > > > of the bypass. The gas to air ratio is too rich and there is really
no
> > way
> > > > to adjust it, or so I'm told. I'm not sure how much the catalytic
> > > converter
> > > > has to do with this but, how can the fuel mixture be adjusted with
the
> > > > bypass in place?
> > > >
> > > >
> > > >
> > > > Thanks,
> > > >
> > > > Chip
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > >
> > >
05-12-2004, 01:28 PM
#19
Guest
Posts: n/a
Re: AMC 150 too rich
ditto.
:)
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:40A24910.4395B719@sympatico.ca...
> Ok, you have the YFA carb.
>
> The fact that it runs pretty decent with the stepper unplugged would
> lead me to believe the mix is at least 'close' by default.
>
> The YFA with the stepper still has the manual mix screw, same as the
> BBD. They hide it under a metal plug in the base plate of the carb.
> Some you can pull the blocking plug out with a point, others have to be
> drilled and pried out.
>
> If you set the carb with the throttle lever in front of you, the mix
> screw will be in the base to your right under the plug likely.
>
> I would highly recommend you get the Haynes CJ manual. It has a great
> section on the carbs.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Chip wrote:
> >
> > The computer was not functioning so the stepper motor was inoperable (or
at
> > least was not being run by the bad computer) Before the bypass was
> > complete, my father started the motor, it ran terrible until he uplugged
the
> > stepper motor, then it ran smooth. How can you tell where the stepper
motor
> > should be and how do you get it there if it is in the wrong place, which
it
> > obviously is because of the amount of gas running through it.
> >
> > Short of solving this carb trouble, what kind of pre-83 carb will fit
the
> > 150 engine?
> >
> > Thanks again,
> >
> > Chip
> >
> > "serg" <sfonNOSPAM@yahoo.com> wrote in message
> > news:2gad30Fiu7bU1@uni-berlin.de...
> > > did u make sure the stepper motor was in the right position before
turning
> > > it off? i never did the nutter bypass in mine before i took it off but
i
> > > remember you had to have the motor in a certain position before
cutting
> > the
> > > wire. is your 02 sensor alive?
> > >
> > > "Chip" <cjenkins1@nospam.neo.rr.com> wrote in message
> > > news:oRSnc.1090$OE3.804@fe1.columbus.rr.com...
> > > > I have a question concerning an '84 CJ with the AMC 150 4 cyl engine
and
> > > one
> > > > of those terrible Carter carburetors with a Nutter bypass performed.
> > Keep
> > > > in mind with this question that the catalytic converter needs to be
> > > replaced
> > > > and another one is on order. Here's the present trouble: The stepper
> > > motor,
> > > > which I believe controls the amount of fuel, has been disconnected
as
> > part
> > > > of the bypass. The gas to air ratio is too rich and there is really
no
> > way
> > > > to adjust it, or so I'm told. I'm not sure how much the catalytic
> > > converter
> > > > has to do with this but, how can the fuel mixture be adjusted with
the
> > > > bypass in place?
> > > >
> > > >
> > > >
> > > > Thanks,
> > > >
> > > > Chip
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > >
> > >
:)
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:40A24910.4395B719@sympatico.ca...
> Ok, you have the YFA carb.
>
> The fact that it runs pretty decent with the stepper unplugged would
> lead me to believe the mix is at least 'close' by default.
>
> The YFA with the stepper still has the manual mix screw, same as the
> BBD. They hide it under a metal plug in the base plate of the carb.
> Some you can pull the blocking plug out with a point, others have to be
> drilled and pried out.
>
> If you set the carb with the throttle lever in front of you, the mix
> screw will be in the base to your right under the plug likely.
>
> I would highly recommend you get the Haynes CJ manual. It has a great
> section on the carbs.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Chip wrote:
> >
> > The computer was not functioning so the stepper motor was inoperable (or
at
> > least was not being run by the bad computer) Before the bypass was
> > complete, my father started the motor, it ran terrible until he uplugged
the
> > stepper motor, then it ran smooth. How can you tell where the stepper
motor
> > should be and how do you get it there if it is in the wrong place, which
it
> > obviously is because of the amount of gas running through it.
> >
> > Short of solving this carb trouble, what kind of pre-83 carb will fit
the
> > 150 engine?
> >
> > Thanks again,
> >
> > Chip
> >
> > "serg" <sfonNOSPAM@yahoo.com> wrote in message
> > news:2gad30Fiu7bU1@uni-berlin.de...
> > > did u make sure the stepper motor was in the right position before
turning
> > > it off? i never did the nutter bypass in mine before i took it off but
i
> > > remember you had to have the motor in a certain position before
cutting
> > the
> > > wire. is your 02 sensor alive?
> > >
> > > "Chip" <cjenkins1@nospam.neo.rr.com> wrote in message
> > > news:oRSnc.1090$OE3.804@fe1.columbus.rr.com...
> > > > I have a question concerning an '84 CJ with the AMC 150 4 cyl engine
and
> > > one
> > > > of those terrible Carter carburetors with a Nutter bypass performed.
> > Keep
> > > > in mind with this question that the catalytic converter needs to be
> > > replaced
> > > > and another one is on order. Here's the present trouble: The stepper
> > > motor,
> > > > which I believe controls the amount of fuel, has been disconnected
as
> > part
> > > > of the bypass. The gas to air ratio is too rich and there is really
no
> > way
> > > > to adjust it, or so I'm told. I'm not sure how much the catalytic
> > > converter
> > > > has to do with this but, how can the fuel mixture be adjusted with
the
> > > > bypass in place?
> > > >
> > > >
> > > >
> > > > Thanks,
> > > >
> > > > Chip
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > >
> > >
05-12-2004, 01:28 PM
#20
Guest
Posts: n/a
Re: AMC 150 too rich
ditto.
:)
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:40A24910.4395B719@sympatico.ca...
> Ok, you have the YFA carb.
>
> The fact that it runs pretty decent with the stepper unplugged would
> lead me to believe the mix is at least 'close' by default.
>
> The YFA with the stepper still has the manual mix screw, same as the
> BBD. They hide it under a metal plug in the base plate of the carb.
> Some you can pull the blocking plug out with a point, others have to be
> drilled and pried out.
>
> If you set the carb with the throttle lever in front of you, the mix
> screw will be in the base to your right under the plug likely.
>
> I would highly recommend you get the Haynes CJ manual. It has a great
> section on the carbs.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Chip wrote:
> >
> > The computer was not functioning so the stepper motor was inoperable (or
at
> > least was not being run by the bad computer) Before the bypass was
> > complete, my father started the motor, it ran terrible until he uplugged
the
> > stepper motor, then it ran smooth. How can you tell where the stepper
motor
> > should be and how do you get it there if it is in the wrong place, which
it
> > obviously is because of the amount of gas running through it.
> >
> > Short of solving this carb trouble, what kind of pre-83 carb will fit
the
> > 150 engine?
> >
> > Thanks again,
> >
> > Chip
> >
> > "serg" <sfonNOSPAM@yahoo.com> wrote in message
> > news:2gad30Fiu7bU1@uni-berlin.de...
> > > did u make sure the stepper motor was in the right position before
turning
> > > it off? i never did the nutter bypass in mine before i took it off but
i
> > > remember you had to have the motor in a certain position before
cutting
> > the
> > > wire. is your 02 sensor alive?
> > >
> > > "Chip" <cjenkins1@nospam.neo.rr.com> wrote in message
> > > news:oRSnc.1090$OE3.804@fe1.columbus.rr.com...
> > > > I have a question concerning an '84 CJ with the AMC 150 4 cyl engine
and
> > > one
> > > > of those terrible Carter carburetors with a Nutter bypass performed.
> > Keep
> > > > in mind with this question that the catalytic converter needs to be
> > > replaced
> > > > and another one is on order. Here's the present trouble: The stepper
> > > motor,
> > > > which I believe controls the amount of fuel, has been disconnected
as
> > part
> > > > of the bypass. The gas to air ratio is too rich and there is really
no
> > way
> > > > to adjust it, or so I'm told. I'm not sure how much the catalytic
> > > converter
> > > > has to do with this but, how can the fuel mixture be adjusted with
the
> > > > bypass in place?
> > > >
> > > >
> > > >
> > > > Thanks,
> > > >
> > > > Chip
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > >
> > >
:)
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:40A24910.4395B719@sympatico.ca...
> Ok, you have the YFA carb.
>
> The fact that it runs pretty decent with the stepper unplugged would
> lead me to believe the mix is at least 'close' by default.
>
> The YFA with the stepper still has the manual mix screw, same as the
> BBD. They hide it under a metal plug in the base plate of the carb.
> Some you can pull the blocking plug out with a point, others have to be
> drilled and pried out.
>
> If you set the carb with the throttle lever in front of you, the mix
> screw will be in the base to your right under the plug likely.
>
> I would highly recommend you get the Haynes CJ manual. It has a great
> section on the carbs.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Chip wrote:
> >
> > The computer was not functioning so the stepper motor was inoperable (or
at
> > least was not being run by the bad computer) Before the bypass was
> > complete, my father started the motor, it ran terrible until he uplugged
the
> > stepper motor, then it ran smooth. How can you tell where the stepper
motor
> > should be and how do you get it there if it is in the wrong place, which
it
> > obviously is because of the amount of gas running through it.
> >
> > Short of solving this carb trouble, what kind of pre-83 carb will fit
the
> > 150 engine?
> >
> > Thanks again,
> >
> > Chip
> >
> > "serg" <sfonNOSPAM@yahoo.com> wrote in message
> > news:2gad30Fiu7bU1@uni-berlin.de...
> > > did u make sure the stepper motor was in the right position before
turning
> > > it off? i never did the nutter bypass in mine before i took it off but
i
> > > remember you had to have the motor in a certain position before
cutting
> > the
> > > wire. is your 02 sensor alive?
> > >
> > > "Chip" <cjenkins1@nospam.neo.rr.com> wrote in message
> > > news:oRSnc.1090$OE3.804@fe1.columbus.rr.com...
> > > > I have a question concerning an '84 CJ with the AMC 150 4 cyl engine
and
> > > one
> > > > of those terrible Carter carburetors with a Nutter bypass performed.
> > Keep
> > > > in mind with this question that the catalytic converter needs to be
> > > replaced
> > > > and another one is on order. Here's the present trouble: The stepper
> > > motor,
> > > > which I believe controls the amount of fuel, has been disconnected
as
> > part
> > > > of the bypass. The gas to air ratio is too rich and there is really
no
> > way
> > > > to adjust it, or so I'm told. I'm not sure how much the catalytic
> > > converter
> > > > has to do with this but, how can the fuel mixture be adjusted with
the
> > > > bypass in place?
> > > >
> > > >
> > > >
> > > > Thanks,
> > > >
> > > > Chip
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > >
> > >
