Aisen-Warner trans problem
Guest
Posts: n/a
Aisen-Warner trans problem
1988 Jeep Cherokee 2wd
4.0 inline 6 cyl.
Tranmission = Aisen-Warner Model 30-40LE
299560 miles
Problem just started. I have only owned this for a few months but it did
shift normally before. When in Overdrive, Drive, 1-2, transmission starts
out in low range but wont shift until speed reaches 35 mph then it shifts
hard to second gear, but doesn't shift to third or overdrive. The
transmission does not seem to be slipping while accelerating but when I let
off the gas it does not slow down as I would expect, but is almost as if it
is coasting. When you give it enough gas that the engine speed reaches the
speed of travel it starts to accelerate again.
I have dropped the transmission pan, replaced pickup screen that wasn't all
that dirty. Fluid is clean, not burned yet. Removed the three solenoid
valves replaced the O-rings on the end of the valves. Checked valves to
insure they opened & closed with battery volts applied. Installed fresh
ATF. All valves work as I would expect. Removed what I think is a speed
sensor in the tailshaft, located above the speedometer cable, that makes &
breaks continuity when a magnet is past near the sensor.
I have a Haynes manual for the unit but the wiring diagrams don't include
transmission control circuit.
Anyone with any ideas, info on how the electronics controls work for
transmission shifts. Could someone tell me if another trans. could be
installed, perhaps a Torqueflight that might bolt up to the 4.0 engine.
Guest
Posts: n/a
Re: Aisen-Warner trans problem
the tranny you have is a good and reliable and long-life design.
a transmission specialist at a local jeep dealer said that he has never had
to rebuild one. ( Even tho that was about 4 years ago.) A friend ('91 jeep)
had the same sort of problem you describe, and was talked into a new
transmission. After that, she still had EXACTLY the same problem.
"Rick" <UseUSENET@THIS GROUP.invalid> wrote in message
news:JQ9jd.394$jC5.180@trnddc07...
>
> 1988 Jeep Cherokee 2wd
> 4.0 inline 6 cyl.
> Tranmission = Aisen-Warner Model 30-40LE
> 299560 miles
>
> Problem just started. I have only owned this for a few months but it did
> shift normally before. When in Overdrive, Drive, 1-2, transmission starts
> out in low range but wont shift until speed reaches 35 mph then it shifts
> hard to second gear, but doesn't shift to third or overdrive. The
> transmission does not seem to be slipping while accelerating but when I
let
> off the gas it does not slow down as I would expect, but is almost as if
it
> is coasting. When you give it enough gas that the engine speed reaches the
> speed of travel it starts to accelerate again.
>
> I have dropped the transmission pan, replaced pickup screen that wasn't
all
> that dirty. Fluid is clean, not burned yet. Removed the three solenoid
> valves replaced the O-rings on the end of the valves. Checked valves to
> insure they opened & closed with battery volts applied. Installed fresh
> ATF. All valves work as I would expect. Removed what I think is a speed
> sensor in the tailshaft, located above the speedometer cable, that makes &
> breaks continuity when a magnet is past near the sensor.
>
> I have a Haynes manual for the unit but the wiring diagrams don't include
> transmission control circuit.
>
> Anyone with any ideas, info on how the electronics controls work for
> transmission shifts. Could someone tell me if another trans. could be
> installed, perhaps a Torqueflight that might bolt up to the 4.0 engine.
>
>
>
>
>
>
>
a transmission specialist at a local jeep dealer said that he has never had
to rebuild one. ( Even tho that was about 4 years ago.) A friend ('91 jeep)
had the same sort of problem you describe, and was talked into a new
transmission. After that, she still had EXACTLY the same problem.
"Rick" <UseUSENET@THIS GROUP.invalid> wrote in message
news:JQ9jd.394$jC5.180@trnddc07...
>
> 1988 Jeep Cherokee 2wd
> 4.0 inline 6 cyl.
> Tranmission = Aisen-Warner Model 30-40LE
> 299560 miles
>
> Problem just started. I have only owned this for a few months but it did
> shift normally before. When in Overdrive, Drive, 1-2, transmission starts
> out in low range but wont shift until speed reaches 35 mph then it shifts
> hard to second gear, but doesn't shift to third or overdrive. The
> transmission does not seem to be slipping while accelerating but when I
let
> off the gas it does not slow down as I would expect, but is almost as if
it
> is coasting. When you give it enough gas that the engine speed reaches the
> speed of travel it starts to accelerate again.
>
> I have dropped the transmission pan, replaced pickup screen that wasn't
all
> that dirty. Fluid is clean, not burned yet. Removed the three solenoid
> valves replaced the O-rings on the end of the valves. Checked valves to
> insure they opened & closed with battery volts applied. Installed fresh
> ATF. All valves work as I would expect. Removed what I think is a speed
> sensor in the tailshaft, located above the speedometer cable, that makes &
> breaks continuity when a magnet is past near the sensor.
>
> I have a Haynes manual for the unit but the wiring diagrams don't include
> transmission control circuit.
>
> Anyone with any ideas, info on how the electronics controls work for
> transmission shifts. Could someone tell me if another trans. could be
> installed, perhaps a Torqueflight that might bolt up to the 4.0 engine.
>
>
>
>
>
>
>
Guest
Posts: n/a
Re: Aisen-Warner trans problem
the tranny you have is a good and reliable and long-life design.
a transmission specialist at a local jeep dealer said that he has never had
to rebuild one. ( Even tho that was about 4 years ago.) A friend ('91 jeep)
had the same sort of problem you describe, and was talked into a new
transmission. After that, she still had EXACTLY the same problem.
"Rick" <UseUSENET@THIS GROUP.invalid> wrote in message
news:JQ9jd.394$jC5.180@trnddc07...
>
> 1988 Jeep Cherokee 2wd
> 4.0 inline 6 cyl.
> Tranmission = Aisen-Warner Model 30-40LE
> 299560 miles
>
> Problem just started. I have only owned this for a few months but it did
> shift normally before. When in Overdrive, Drive, 1-2, transmission starts
> out in low range but wont shift until speed reaches 35 mph then it shifts
> hard to second gear, but doesn't shift to third or overdrive. The
> transmission does not seem to be slipping while accelerating but when I
let
> off the gas it does not slow down as I would expect, but is almost as if
it
> is coasting. When you give it enough gas that the engine speed reaches the
> speed of travel it starts to accelerate again.
>
> I have dropped the transmission pan, replaced pickup screen that wasn't
all
> that dirty. Fluid is clean, not burned yet. Removed the three solenoid
> valves replaced the O-rings on the end of the valves. Checked valves to
> insure they opened & closed with battery volts applied. Installed fresh
> ATF. All valves work as I would expect. Removed what I think is a speed
> sensor in the tailshaft, located above the speedometer cable, that makes &
> breaks continuity when a magnet is past near the sensor.
>
> I have a Haynes manual for the unit but the wiring diagrams don't include
> transmission control circuit.
>
> Anyone with any ideas, info on how the electronics controls work for
> transmission shifts. Could someone tell me if another trans. could be
> installed, perhaps a Torqueflight that might bolt up to the 4.0 engine.
>
>
>
>
>
>
>
a transmission specialist at a local jeep dealer said that he has never had
to rebuild one. ( Even tho that was about 4 years ago.) A friend ('91 jeep)
had the same sort of problem you describe, and was talked into a new
transmission. After that, she still had EXACTLY the same problem.
"Rick" <UseUSENET@THIS GROUP.invalid> wrote in message
news:JQ9jd.394$jC5.180@trnddc07...
>
> 1988 Jeep Cherokee 2wd
> 4.0 inline 6 cyl.
> Tranmission = Aisen-Warner Model 30-40LE
> 299560 miles
>
> Problem just started. I have only owned this for a few months but it did
> shift normally before. When in Overdrive, Drive, 1-2, transmission starts
> out in low range but wont shift until speed reaches 35 mph then it shifts
> hard to second gear, but doesn't shift to third or overdrive. The
> transmission does not seem to be slipping while accelerating but when I
let
> off the gas it does not slow down as I would expect, but is almost as if
it
> is coasting. When you give it enough gas that the engine speed reaches the
> speed of travel it starts to accelerate again.
>
> I have dropped the transmission pan, replaced pickup screen that wasn't
all
> that dirty. Fluid is clean, not burned yet. Removed the three solenoid
> valves replaced the O-rings on the end of the valves. Checked valves to
> insure they opened & closed with battery volts applied. Installed fresh
> ATF. All valves work as I would expect. Removed what I think is a speed
> sensor in the tailshaft, located above the speedometer cable, that makes &
> breaks continuity when a magnet is past near the sensor.
>
> I have a Haynes manual for the unit but the wiring diagrams don't include
> transmission control circuit.
>
> Anyone with any ideas, info on how the electronics controls work for
> transmission shifts. Could someone tell me if another trans. could be
> installed, perhaps a Torqueflight that might bolt up to the 4.0 engine.
>
>
>
>
>
>
>
Guest
Posts: n/a
Re: Aisen-Warner trans problem
May be a computer problem as with the newer Cherokee AW4s (another
name for the same):
http://www.transonline.com/transdige...ers/index.html
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Rick wrote:
>
> 1988 Jeep Cherokee 2wd
> 4.0 inline 6 cyl.
> Tranmission = Aisen-Warner Model 30-40LE
> 299560 miles
>
> Problem just started. I have only owned this for a few months but it did
> shift normally before. When in Overdrive, Drive, 1-2, transmission starts
> out in low range but wont shift until speed reaches 35 mph then it shifts
> hard to second gear, but doesn't shift to third or overdrive. The
> transmission does not seem to be slipping while accelerating but when I let
> off the gas it does not slow down as I would expect, but is almost as if it
> is coasting. When you give it enough gas that the engine speed reaches the
> speed of travel it starts to accelerate again.
>
> I have dropped the transmission pan, replaced pickup screen that wasn't all
> that dirty. Fluid is clean, not burned yet. Removed the three solenoid
> valves replaced the O-rings on the end of the valves. Checked valves to
> insure they opened & closed with battery volts applied. Installed fresh
> ATF. All valves work as I would expect. Removed what I think is a speed
> sensor in the tailshaft, located above the speedometer cable, that makes &
> breaks continuity when a magnet is past near the sensor.
>
> I have a Haynes manual for the unit but the wiring diagrams don't include
> transmission control circuit.
>
> Anyone with any ideas, info on how the electronics controls work for
> transmission shifts. Could someone tell me if another trans. could be
> installed, perhaps a Torqueflight that might bolt up to the 4.0 engine.
>
>
name for the same):
http://www.transonline.com/transdige...ers/index.html
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Rick wrote:
>
> 1988 Jeep Cherokee 2wd
> 4.0 inline 6 cyl.
> Tranmission = Aisen-Warner Model 30-40LE
> 299560 miles
>
> Problem just started. I have only owned this for a few months but it did
> shift normally before. When in Overdrive, Drive, 1-2, transmission starts
> out in low range but wont shift until speed reaches 35 mph then it shifts
> hard to second gear, but doesn't shift to third or overdrive. The
> transmission does not seem to be slipping while accelerating but when I let
> off the gas it does not slow down as I would expect, but is almost as if it
> is coasting. When you give it enough gas that the engine speed reaches the
> speed of travel it starts to accelerate again.
>
> I have dropped the transmission pan, replaced pickup screen that wasn't all
> that dirty. Fluid is clean, not burned yet. Removed the three solenoid
> valves replaced the O-rings on the end of the valves. Checked valves to
> insure they opened & closed with battery volts applied. Installed fresh
> ATF. All valves work as I would expect. Removed what I think is a speed
> sensor in the tailshaft, located above the speedometer cable, that makes &
> breaks continuity when a magnet is past near the sensor.
>
> I have a Haynes manual for the unit but the wiring diagrams don't include
> transmission control circuit.
>
> Anyone with any ideas, info on how the electronics controls work for
> transmission shifts. Could someone tell me if another trans. could be
> installed, perhaps a Torqueflight that might bolt up to the 4.0 engine.
>
>
Guest
Posts: n/a
Re: Aisen-Warner trans problem
May be a computer problem as with the newer Cherokee AW4s (another
name for the same):
http://www.transonline.com/transdige...ers/index.html
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Rick wrote:
>
> 1988 Jeep Cherokee 2wd
> 4.0 inline 6 cyl.
> Tranmission = Aisen-Warner Model 30-40LE
> 299560 miles
>
> Problem just started. I have only owned this for a few months but it did
> shift normally before. When in Overdrive, Drive, 1-2, transmission starts
> out in low range but wont shift until speed reaches 35 mph then it shifts
> hard to second gear, but doesn't shift to third or overdrive. The
> transmission does not seem to be slipping while accelerating but when I let
> off the gas it does not slow down as I would expect, but is almost as if it
> is coasting. When you give it enough gas that the engine speed reaches the
> speed of travel it starts to accelerate again.
>
> I have dropped the transmission pan, replaced pickup screen that wasn't all
> that dirty. Fluid is clean, not burned yet. Removed the three solenoid
> valves replaced the O-rings on the end of the valves. Checked valves to
> insure they opened & closed with battery volts applied. Installed fresh
> ATF. All valves work as I would expect. Removed what I think is a speed
> sensor in the tailshaft, located above the speedometer cable, that makes &
> breaks continuity when a magnet is past near the sensor.
>
> I have a Haynes manual for the unit but the wiring diagrams don't include
> transmission control circuit.
>
> Anyone with any ideas, info on how the electronics controls work for
> transmission shifts. Could someone tell me if another trans. could be
> installed, perhaps a Torqueflight that might bolt up to the 4.0 engine.
>
>
name for the same):
http://www.transonline.com/transdige...ers/index.html
God Bless America, ßill O|||||||O
mailto:-------------------- http://www.----------.com/
Rick wrote:
>
> 1988 Jeep Cherokee 2wd
> 4.0 inline 6 cyl.
> Tranmission = Aisen-Warner Model 30-40LE
> 299560 miles
>
> Problem just started. I have only owned this for a few months but it did
> shift normally before. When in Overdrive, Drive, 1-2, transmission starts
> out in low range but wont shift until speed reaches 35 mph then it shifts
> hard to second gear, but doesn't shift to third or overdrive. The
> transmission does not seem to be slipping while accelerating but when I let
> off the gas it does not slow down as I would expect, but is almost as if it
> is coasting. When you give it enough gas that the engine speed reaches the
> speed of travel it starts to accelerate again.
>
> I have dropped the transmission pan, replaced pickup screen that wasn't all
> that dirty. Fluid is clean, not burned yet. Removed the three solenoid
> valves replaced the O-rings on the end of the valves. Checked valves to
> insure they opened & closed with battery volts applied. Installed fresh
> ATF. All valves work as I would expect. Removed what I think is a speed
> sensor in the tailshaft, located above the speedometer cable, that makes &
> breaks continuity when a magnet is past near the sensor.
>
> I have a Haynes manual for the unit but the wiring diagrams don't include
> transmission control circuit.
>
> Anyone with any ideas, info on how the electronics controls work for
> transmission shifts. Could someone tell me if another trans. could be
> installed, perhaps a Torqueflight that might bolt up to the 4.0 engine.
>
>
Guest
Posts: n/a
Re: Aisen-Warner trans problem
Does it shift like it thinks the pedel is on the floor? If so check the
readings of you TPS (Throttle Position Sensor). This problem comes up about
once a week here. the procedure is in the Haynes. Also note the standard and
automatic ones are different. If that's not the problem there's a lot of
info here.
http://www.transonline.com/transdige...ers/index.html
JoBo
"Rick" <UseUSENET@THIS GROUP.invalid> wrote in message
news:JQ9jd.394$jC5.180@trnddc07...
>
> 1988 Jeep Cherokee 2wd
> 4.0 inline 6 cyl.
> Tranmission = Aisen-Warner Model 30-40LE
> 299560 miles
>
> Problem just started. I have only owned this for a few months but it did
> shift normally before. When in Overdrive, Drive, 1-2, transmission starts
> out in low range but wont shift until speed reaches 35 mph then it shifts
> hard to second gear, but doesn't shift to third or overdrive. The
> transmission does not seem to be slipping while accelerating but when I
let
> off the gas it does not slow down as I would expect, but is almost as if
it
> is coasting. When you give it enough gas that the engine speed reaches the
> speed of travel it starts to accelerate again.
>
> I have dropped the transmission pan, replaced pickup screen that wasn't
all
> that dirty. Fluid is clean, not burned yet. Removed the three solenoid
> valves replaced the O-rings on the end of the valves. Checked valves to
> insure they opened & closed with battery volts applied. Installed fresh
> ATF. All valves work as I would expect. Removed what I think is a speed
> sensor in the tailshaft, located above the speedometer cable, that makes &
> breaks continuity when a magnet is past near the sensor.
>
> I have a Haynes manual for the unit but the wiring diagrams don't include
> transmission control circuit.
>
> Anyone with any ideas, info on how the electronics controls work for
> transmission shifts. Could someone tell me if another trans. could be
> installed, perhaps a Torqueflight that might bolt up to the 4.0 engine.
>
>
>
>
>
>
>
readings of you TPS (Throttle Position Sensor). This problem comes up about
once a week here. the procedure is in the Haynes. Also note the standard and
automatic ones are different. If that's not the problem there's a lot of
info here.
http://www.transonline.com/transdige...ers/index.html
JoBo
"Rick" <UseUSENET@THIS GROUP.invalid> wrote in message
news:JQ9jd.394$jC5.180@trnddc07...
>
> 1988 Jeep Cherokee 2wd
> 4.0 inline 6 cyl.
> Tranmission = Aisen-Warner Model 30-40LE
> 299560 miles
>
> Problem just started. I have only owned this for a few months but it did
> shift normally before. When in Overdrive, Drive, 1-2, transmission starts
> out in low range but wont shift until speed reaches 35 mph then it shifts
> hard to second gear, but doesn't shift to third or overdrive. The
> transmission does not seem to be slipping while accelerating but when I
let
> off the gas it does not slow down as I would expect, but is almost as if
it
> is coasting. When you give it enough gas that the engine speed reaches the
> speed of travel it starts to accelerate again.
>
> I have dropped the transmission pan, replaced pickup screen that wasn't
all
> that dirty. Fluid is clean, not burned yet. Removed the three solenoid
> valves replaced the O-rings on the end of the valves. Checked valves to
> insure they opened & closed with battery volts applied. Installed fresh
> ATF. All valves work as I would expect. Removed what I think is a speed
> sensor in the tailshaft, located above the speedometer cable, that makes &
> breaks continuity when a magnet is past near the sensor.
>
> I have a Haynes manual for the unit but the wiring diagrams don't include
> transmission control circuit.
>
> Anyone with any ideas, info on how the electronics controls work for
> transmission shifts. Could someone tell me if another trans. could be
> installed, perhaps a Torqueflight that might bolt up to the 4.0 engine.
>
>
>
>
>
>
>
Guest
Posts: n/a
Re: Aisen-Warner trans problem
Does it shift like it thinks the pedel is on the floor? If so check the
readings of you TPS (Throttle Position Sensor). This problem comes up about
once a week here. the procedure is in the Haynes. Also note the standard and
automatic ones are different. If that's not the problem there's a lot of
info here.
http://www.transonline.com/transdige...ers/index.html
JoBo
"Rick" <UseUSENET@THIS GROUP.invalid> wrote in message
news:JQ9jd.394$jC5.180@trnddc07...
>
> 1988 Jeep Cherokee 2wd
> 4.0 inline 6 cyl.
> Tranmission = Aisen-Warner Model 30-40LE
> 299560 miles
>
> Problem just started. I have only owned this for a few months but it did
> shift normally before. When in Overdrive, Drive, 1-2, transmission starts
> out in low range but wont shift until speed reaches 35 mph then it shifts
> hard to second gear, but doesn't shift to third or overdrive. The
> transmission does not seem to be slipping while accelerating but when I
let
> off the gas it does not slow down as I would expect, but is almost as if
it
> is coasting. When you give it enough gas that the engine speed reaches the
> speed of travel it starts to accelerate again.
>
> I have dropped the transmission pan, replaced pickup screen that wasn't
all
> that dirty. Fluid is clean, not burned yet. Removed the three solenoid
> valves replaced the O-rings on the end of the valves. Checked valves to
> insure they opened & closed with battery volts applied. Installed fresh
> ATF. All valves work as I would expect. Removed what I think is a speed
> sensor in the tailshaft, located above the speedometer cable, that makes &
> breaks continuity when a magnet is past near the sensor.
>
> I have a Haynes manual for the unit but the wiring diagrams don't include
> transmission control circuit.
>
> Anyone with any ideas, info on how the electronics controls work for
> transmission shifts. Could someone tell me if another trans. could be
> installed, perhaps a Torqueflight that might bolt up to the 4.0 engine.
>
>
>
>
>
>
>
readings of you TPS (Throttle Position Sensor). This problem comes up about
once a week here. the procedure is in the Haynes. Also note the standard and
automatic ones are different. If that's not the problem there's a lot of
info here.
http://www.transonline.com/transdige...ers/index.html
JoBo
"Rick" <UseUSENET@THIS GROUP.invalid> wrote in message
news:JQ9jd.394$jC5.180@trnddc07...
>
> 1988 Jeep Cherokee 2wd
> 4.0 inline 6 cyl.
> Tranmission = Aisen-Warner Model 30-40LE
> 299560 miles
>
> Problem just started. I have only owned this for a few months but it did
> shift normally before. When in Overdrive, Drive, 1-2, transmission starts
> out in low range but wont shift until speed reaches 35 mph then it shifts
> hard to second gear, but doesn't shift to third or overdrive. The
> transmission does not seem to be slipping while accelerating but when I
let
> off the gas it does not slow down as I would expect, but is almost as if
it
> is coasting. When you give it enough gas that the engine speed reaches the
> speed of travel it starts to accelerate again.
>
> I have dropped the transmission pan, replaced pickup screen that wasn't
all
> that dirty. Fluid is clean, not burned yet. Removed the three solenoid
> valves replaced the O-rings on the end of the valves. Checked valves to
> insure they opened & closed with battery volts applied. Installed fresh
> ATF. All valves work as I would expect. Removed what I think is a speed
> sensor in the tailshaft, located above the speedometer cable, that makes &
> breaks continuity when a magnet is past near the sensor.
>
> I have a Haynes manual for the unit but the wiring diagrams don't include
> transmission control circuit.
>
> Anyone with any ideas, info on how the electronics controls work for
> transmission shifts. Could someone tell me if another trans. could be
> installed, perhaps a Torqueflight that might bolt up to the 4.0 engine.
>
>
>
>
>
>
>
Guest
Posts: n/a
Re: Aisen-Warner trans problem
Drop the pan and check the band clearance 90% of the owners never have them
checked.
HarryS
"Rick" <UseUSENET@THIS GROUP.invalid> wrote in message
news:JQ9jd.394$jC5.180@trnddc07...
>
> 1988 Jeep Cherokee 2wd
> 4.0 inline 6 cyl.
> Tranmission = Aisen-Warner Model 30-40LE
> 299560 miles
>
> Problem just started. I have only owned this for a few months but it did
> shift normally before. When in Overdrive, Drive, 1-2, transmission starts
> out in low range but wont shift until speed reaches 35 mph then it shifts
> hard to second gear, but doesn't shift to third or overdrive. The
> transmission does not seem to be slipping while accelerating but when I
> let
> off the gas it does not slow down as I would expect, but is almost as if
> it
> is coasting. When you give it enough gas that the engine speed reaches the
> speed of travel it starts to accelerate again.
>
> I have dropped the transmission pan, replaced pickup screen that wasn't
> all
> that dirty. Fluid is clean, not burned yet. Removed the three solenoid
> valves replaced the O-rings on the end of the valves. Checked valves to
> insure they opened & closed with battery volts applied. Installed fresh
> ATF. All valves work as I would expect. Removed what I think is a speed
> sensor in the tailshaft, located above the speedometer cable, that makes &
> breaks continuity when a magnet is past near the sensor.
>
> I have a Haynes manual for the unit but the wiring diagrams don't include
> transmission control circuit.
>
> Anyone with any ideas, info on how the electronics controls work for
> transmission shifts. Could someone tell me if another trans. could be
> installed, perhaps a Torqueflight that might bolt up to the 4.0 engine.
>
>
>
>
>
>
>
checked.
HarryS
"Rick" <UseUSENET@THIS GROUP.invalid> wrote in message
news:JQ9jd.394$jC5.180@trnddc07...
>
> 1988 Jeep Cherokee 2wd
> 4.0 inline 6 cyl.
> Tranmission = Aisen-Warner Model 30-40LE
> 299560 miles
>
> Problem just started. I have only owned this for a few months but it did
> shift normally before. When in Overdrive, Drive, 1-2, transmission starts
> out in low range but wont shift until speed reaches 35 mph then it shifts
> hard to second gear, but doesn't shift to third or overdrive. The
> transmission does not seem to be slipping while accelerating but when I
> let
> off the gas it does not slow down as I would expect, but is almost as if
> it
> is coasting. When you give it enough gas that the engine speed reaches the
> speed of travel it starts to accelerate again.
>
> I have dropped the transmission pan, replaced pickup screen that wasn't
> all
> that dirty. Fluid is clean, not burned yet. Removed the three solenoid
> valves replaced the O-rings on the end of the valves. Checked valves to
> insure they opened & closed with battery volts applied. Installed fresh
> ATF. All valves work as I would expect. Removed what I think is a speed
> sensor in the tailshaft, located above the speedometer cable, that makes &
> breaks continuity when a magnet is past near the sensor.
>
> I have a Haynes manual for the unit but the wiring diagrams don't include
> transmission control circuit.
>
> Anyone with any ideas, info on how the electronics controls work for
> transmission shifts. Could someone tell me if another trans. could be
> installed, perhaps a Torqueflight that might bolt up to the 4.0 engine.
>
>
>
>
>
>
>
Guest
Posts: n/a
Re: Aisen-Warner trans problem
Drop the pan and check the band clearance 90% of the owners never have them
checked.
HarryS
"Rick" <UseUSENET@THIS GROUP.invalid> wrote in message
news:JQ9jd.394$jC5.180@trnddc07...
>
> 1988 Jeep Cherokee 2wd
> 4.0 inline 6 cyl.
> Tranmission = Aisen-Warner Model 30-40LE
> 299560 miles
>
> Problem just started. I have only owned this for a few months but it did
> shift normally before. When in Overdrive, Drive, 1-2, transmission starts
> out in low range but wont shift until speed reaches 35 mph then it shifts
> hard to second gear, but doesn't shift to third or overdrive. The
> transmission does not seem to be slipping while accelerating but when I
> let
> off the gas it does not slow down as I would expect, but is almost as if
> it
> is coasting. When you give it enough gas that the engine speed reaches the
> speed of travel it starts to accelerate again.
>
> I have dropped the transmission pan, replaced pickup screen that wasn't
> all
> that dirty. Fluid is clean, not burned yet. Removed the three solenoid
> valves replaced the O-rings on the end of the valves. Checked valves to
> insure they opened & closed with battery volts applied. Installed fresh
> ATF. All valves work as I would expect. Removed what I think is a speed
> sensor in the tailshaft, located above the speedometer cable, that makes &
> breaks continuity when a magnet is past near the sensor.
>
> I have a Haynes manual for the unit but the wiring diagrams don't include
> transmission control circuit.
>
> Anyone with any ideas, info on how the electronics controls work for
> transmission shifts. Could someone tell me if another trans. could be
> installed, perhaps a Torqueflight that might bolt up to the 4.0 engine.
>
>
>
>
>
>
>
checked.
HarryS
"Rick" <UseUSENET@THIS GROUP.invalid> wrote in message
news:JQ9jd.394$jC5.180@trnddc07...
>
> 1988 Jeep Cherokee 2wd
> 4.0 inline 6 cyl.
> Tranmission = Aisen-Warner Model 30-40LE
> 299560 miles
>
> Problem just started. I have only owned this for a few months but it did
> shift normally before. When in Overdrive, Drive, 1-2, transmission starts
> out in low range but wont shift until speed reaches 35 mph then it shifts
> hard to second gear, but doesn't shift to third or overdrive. The
> transmission does not seem to be slipping while accelerating but when I
> let
> off the gas it does not slow down as I would expect, but is almost as if
> it
> is coasting. When you give it enough gas that the engine speed reaches the
> speed of travel it starts to accelerate again.
>
> I have dropped the transmission pan, replaced pickup screen that wasn't
> all
> that dirty. Fluid is clean, not burned yet. Removed the three solenoid
> valves replaced the O-rings on the end of the valves. Checked valves to
> insure they opened & closed with battery volts applied. Installed fresh
> ATF. All valves work as I would expect. Removed what I think is a speed
> sensor in the tailshaft, located above the speedometer cable, that makes &
> breaks continuity when a magnet is past near the sensor.
>
> I have a Haynes manual for the unit but the wiring diagrams don't include
> transmission control circuit.
>
> Anyone with any ideas, info on how the electronics controls work for
> transmission shifts. Could someone tell me if another trans. could be
> installed, perhaps a Torqueflight that might bolt up to the 4.0 engine.
>
>
>
>
>
>
>
Guest
Posts: n/a
Re: Aisen-Warner trans problem
L.W.(ßill) ------ III wrote:
> May be a computer problem as with the newer Cherokee AW4s (another
> name for the same):
>
http://www.transonline.com/transdige...ers/index.html
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
Thanks for the link. I will see if I can find trans. control and break out
the DVOM to check specs at connector.
> May be a computer problem as with the newer Cherokee AW4s (another
> name for the same):
>
http://www.transonline.com/transdige...ers/index.html
> God Bless America, ßill O|||||||O
> mailto:-------------------- http://www.----------.com/
>
Thanks for the link. I will see if I can find trans. control and break out
the DVOM to check specs at connector.
