AC relay
#1
Guest
Posts: n/a
AC relay
On my '00 XJ 4.0 AW4, the engine RPM kept surging up when at idle. I
determined that the AC compressor was cycling on and off no matter which
position the HVAC system was set to ( I know the AC comes on when in defrost
mode). This happened at approximately 45 second intervals. I pulled the AC
relay and the compressor no longer cycles (and my AC obviously doesn't
work). Do I just need a new relay or is it something bigger?
Carl
determined that the AC compressor was cycling on and off no matter which
position the HVAC system was set to ( I know the AC comes on when in defrost
mode). This happened at approximately 45 second intervals. I pulled the AC
relay and the compressor no longer cycles (and my AC obviously doesn't
work). Do I just need a new relay or is it something bigger?
Carl
#2
Guest
Posts: n/a
Re: AC relay
FWIW, it cycles even when on Hot and Vent, and not in the AC position. The
AC does blow cold when in the AC mode.
Carl
"Carl" <carlsaiyed@hotmailREMOVE.com> wrote in message
news:xdqdnV3l-MlOrMTYnZ2dnUVZ_uadnZ2d@comcast.com...
> On my '00 XJ 4.0 AW4, the engine RPM kept surging up when at idle. I
> determined that the AC compressor was cycling on and off no matter which
> position the HVAC system was set to ( I know the AC comes on when in
> defrost mode). This happened at approximately 45 second intervals. I
> pulled the AC relay and the compressor no longer cycles (and my AC
> obviously doesn't work). Do I just need a new relay or is it something
> bigger?
>
> Carl
>
AC does blow cold when in the AC mode.
Carl
"Carl" <carlsaiyed@hotmailREMOVE.com> wrote in message
news:xdqdnV3l-MlOrMTYnZ2dnUVZ_uadnZ2d@comcast.com...
> On my '00 XJ 4.0 AW4, the engine RPM kept surging up when at idle. I
> determined that the AC compressor was cycling on and off no matter which
> position the HVAC system was set to ( I know the AC comes on when in
> defrost mode). This happened at approximately 45 second intervals. I
> pulled the AC relay and the compressor no longer cycles (and my AC
> obviously doesn't work). Do I just need a new relay or is it something
> bigger?
>
> Carl
>
#3
Guest
Posts: n/a
Re: AC relay
FWIW, it cycles even when on Hot and Vent, and not in the AC position. The
AC does blow cold when in the AC mode.
Carl
"Carl" <carlsaiyed@hotmailREMOVE.com> wrote in message
news:xdqdnV3l-MlOrMTYnZ2dnUVZ_uadnZ2d@comcast.com...
> On my '00 XJ 4.0 AW4, the engine RPM kept surging up when at idle. I
> determined that the AC compressor was cycling on and off no matter which
> position the HVAC system was set to ( I know the AC comes on when in
> defrost mode). This happened at approximately 45 second intervals. I
> pulled the AC relay and the compressor no longer cycles (and my AC
> obviously doesn't work). Do I just need a new relay or is it something
> bigger?
>
> Carl
>
AC does blow cold when in the AC mode.
Carl
"Carl" <carlsaiyed@hotmailREMOVE.com> wrote in message
news:xdqdnV3l-MlOrMTYnZ2dnUVZ_uadnZ2d@comcast.com...
> On my '00 XJ 4.0 AW4, the engine RPM kept surging up when at idle. I
> determined that the AC compressor was cycling on and off no matter which
> position the HVAC system was set to ( I know the AC comes on when in
> defrost mode). This happened at approximately 45 second intervals. I
> pulled the AC relay and the compressor no longer cycles (and my AC
> obviously doesn't work). Do I just need a new relay or is it something
> bigger?
>
> Carl
>
#4
Guest
Posts: n/a
Re: AC relay
FWIW, it cycles even when on Hot and Vent, and not in the AC position. The
AC does blow cold when in the AC mode.
Carl
"Carl" <carlsaiyed@hotmailREMOVE.com> wrote in message
news:xdqdnV3l-MlOrMTYnZ2dnUVZ_uadnZ2d@comcast.com...
> On my '00 XJ 4.0 AW4, the engine RPM kept surging up when at idle. I
> determined that the AC compressor was cycling on and off no matter which
> position the HVAC system was set to ( I know the AC comes on when in
> defrost mode). This happened at approximately 45 second intervals. I
> pulled the AC relay and the compressor no longer cycles (and my AC
> obviously doesn't work). Do I just need a new relay or is it something
> bigger?
>
> Carl
>
AC does blow cold when in the AC mode.
Carl
"Carl" <carlsaiyed@hotmailREMOVE.com> wrote in message
news:xdqdnV3l-MlOrMTYnZ2dnUVZ_uadnZ2d@comcast.com...
> On my '00 XJ 4.0 AW4, the engine RPM kept surging up when at idle. I
> determined that the AC compressor was cycling on and off no matter which
> position the HVAC system was set to ( I know the AC comes on when in
> defrost mode). This happened at approximately 45 second intervals. I
> pulled the AC relay and the compressor no longer cycles (and my AC
> obviously doesn't work). Do I just need a new relay or is it something
> bigger?
>
> Carl
>
#5
Guest
Posts: n/a
Re: AC relay
Carl wrote:
> Do I just need a new relay or is it something bigger?
It's either the dash blend assembly switch or a malfunctioning relay.
Test the signal lead from the dash selector with a voltmeter first
(switch between vent and A/C and check for 12v signal), and if that
checks out, then the problem is most likely the relay.
I've never seen what the relay looks like. If it's like the older
mechanical types, it's possible to clean/repair it instead. I've done
this with mechanical voltage relays in the past.
> Do I just need a new relay or is it something bigger?
It's either the dash blend assembly switch or a malfunctioning relay.
Test the signal lead from the dash selector with a voltmeter first
(switch between vent and A/C and check for 12v signal), and if that
checks out, then the problem is most likely the relay.
I've never seen what the relay looks like. If it's like the older
mechanical types, it's possible to clean/repair it instead. I've done
this with mechanical voltage relays in the past.
#6
Guest
Posts: n/a
Re: AC relay
Carl wrote:
> Do I just need a new relay or is it something bigger?
It's either the dash blend assembly switch or a malfunctioning relay.
Test the signal lead from the dash selector with a voltmeter first
(switch between vent and A/C and check for 12v signal), and if that
checks out, then the problem is most likely the relay.
I've never seen what the relay looks like. If it's like the older
mechanical types, it's possible to clean/repair it instead. I've done
this with mechanical voltage relays in the past.
> Do I just need a new relay or is it something bigger?
It's either the dash blend assembly switch or a malfunctioning relay.
Test the signal lead from the dash selector with a voltmeter first
(switch between vent and A/C and check for 12v signal), and if that
checks out, then the problem is most likely the relay.
I've never seen what the relay looks like. If it's like the older
mechanical types, it's possible to clean/repair it instead. I've done
this with mechanical voltage relays in the past.
#7
Guest
Posts: n/a
Re: AC relay
Carl wrote:
> Do I just need a new relay or is it something bigger?
It's either the dash blend assembly switch or a malfunctioning relay.
Test the signal lead from the dash selector with a voltmeter first
(switch between vent and A/C and check for 12v signal), and if that
checks out, then the problem is most likely the relay.
I've never seen what the relay looks like. If it's like the older
mechanical types, it's possible to clean/repair it instead. I've done
this with mechanical voltage relays in the past.
> Do I just need a new relay or is it something bigger?
It's either the dash blend assembly switch or a malfunctioning relay.
Test the signal lead from the dash selector with a voltmeter first
(switch between vent and A/C and check for 12v signal), and if that
checks out, then the problem is most likely the relay.
I've never seen what the relay looks like. If it's like the older
mechanical types, it's possible to clean/repair it instead. I've done
this with mechanical voltage relays in the past.
#8
Guest
Posts: n/a
Re: AC relay
Maybe it was the fuse I pulled. It was in the engine compartment fuse box.
Carl
"Outatime" <WhoKnows@here.com> wrote in message
news:7sadnRIGsN6DRcTYnZ2dnUVZ_vCdnZ2d@softcom.net. ..
> Carl wrote:
>
>> Do I just need a new relay or is it something bigger?
>
> It's either the dash blend assembly switch or a malfunctioning relay. Test
> the signal lead from the dash selector with a voltmeter first (switch
> between vent and A/C and check for 12v signal), and if that checks out,
> then the problem is most likely the relay.
>
> I've never seen what the relay looks like. If it's like the older
> mechanical types, it's possible to clean/repair it instead. I've done
> this with mechanical voltage relays in the past.
>
Carl
"Outatime" <WhoKnows@here.com> wrote in message
news:7sadnRIGsN6DRcTYnZ2dnUVZ_vCdnZ2d@softcom.net. ..
> Carl wrote:
>
>> Do I just need a new relay or is it something bigger?
>
> It's either the dash blend assembly switch or a malfunctioning relay. Test
> the signal lead from the dash selector with a voltmeter first (switch
> between vent and A/C and check for 12v signal), and if that checks out,
> then the problem is most likely the relay.
>
> I've never seen what the relay looks like. If it's like the older
> mechanical types, it's possible to clean/repair it instead. I've done
> this with mechanical voltage relays in the past.
>
#9
Guest
Posts: n/a
Re: AC relay
Maybe it was the fuse I pulled. It was in the engine compartment fuse box.
Carl
"Outatime" <WhoKnows@here.com> wrote in message
news:7sadnRIGsN6DRcTYnZ2dnUVZ_vCdnZ2d@softcom.net. ..
> Carl wrote:
>
>> Do I just need a new relay or is it something bigger?
>
> It's either the dash blend assembly switch or a malfunctioning relay. Test
> the signal lead from the dash selector with a voltmeter first (switch
> between vent and A/C and check for 12v signal), and if that checks out,
> then the problem is most likely the relay.
>
> I've never seen what the relay looks like. If it's like the older
> mechanical types, it's possible to clean/repair it instead. I've done
> this with mechanical voltage relays in the past.
>
Carl
"Outatime" <WhoKnows@here.com> wrote in message
news:7sadnRIGsN6DRcTYnZ2dnUVZ_vCdnZ2d@softcom.net. ..
> Carl wrote:
>
>> Do I just need a new relay or is it something bigger?
>
> It's either the dash blend assembly switch or a malfunctioning relay. Test
> the signal lead from the dash selector with a voltmeter first (switch
> between vent and A/C and check for 12v signal), and if that checks out,
> then the problem is most likely the relay.
>
> I've never seen what the relay looks like. If it's like the older
> mechanical types, it's possible to clean/repair it instead. I've done
> this with mechanical voltage relays in the past.
>
#10
Guest
Posts: n/a
Re: AC relay
Maybe it was the fuse I pulled. It was in the engine compartment fuse box.
Carl
"Outatime" <WhoKnows@here.com> wrote in message
news:7sadnRIGsN6DRcTYnZ2dnUVZ_vCdnZ2d@softcom.net. ..
> Carl wrote:
>
>> Do I just need a new relay or is it something bigger?
>
> It's either the dash blend assembly switch or a malfunctioning relay. Test
> the signal lead from the dash selector with a voltmeter first (switch
> between vent and A/C and check for 12v signal), and if that checks out,
> then the problem is most likely the relay.
>
> I've never seen what the relay looks like. If it's like the older
> mechanical types, it's possible to clean/repair it instead. I've done
> this with mechanical voltage relays in the past.
>
Carl
"Outatime" <WhoKnows@here.com> wrote in message
news:7sadnRIGsN6DRcTYnZ2dnUVZ_vCdnZ2d@softcom.net. ..
> Carl wrote:
>
>> Do I just need a new relay or is it something bigger?
>
> It's either the dash blend assembly switch or a malfunctioning relay. Test
> the signal lead from the dash selector with a voltmeter first (switch
> between vent and A/C and check for 12v signal), and if that checks out,
> then the problem is most likely the relay.
>
> I've never seen what the relay looks like. If it's like the older
> mechanical types, it's possible to clean/repair it instead. I've done
> this with mechanical voltage relays in the past.
>
Thread
Thread Starter
Forum
Replies
Last Post
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)