98 Wrangler: No Wipers
Guest
Posts: n/a
98 Wrangler: No Wipers
Worst snow storm of the year going this morning and I go out to my TJ
and discover that I don't have any wiper action. Fuse is good. What
do y'all recommend as my next move? (P.S. Where is the wiper motor,
anyway?)
Thanks,
Mark
'98 TJ
'98 XJ
and discover that I don't have any wiper action. Fuse is good. What
do y'all recommend as my next move? (P.S. Where is the wiper motor,
anyway?)
Thanks,
Mark
'98 TJ
'98 XJ
Guest
Posts: n/a
Re: 98 Wrangler: No Wipers
I would try to gently pry them away from the frozen windshield while
hoping ice didn't cook the module.
Someone else posted recently that the TJ also has some kind of gap that
allows ice to build up on the linkages. He had to remove the cowl cover
on the hood to get at it. (guessing that's where the motor is?)
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"M. E. Bye" wrote:
>
> Worst snow storm of the year going this morning and I go out to my TJ
> and discover that I don't have any wiper action. Fuse is good. What
> do y'all recommend as my next move? (P.S. Where is the wiper motor,
> anyway?)
>
> Thanks,
>
> Mark
> '98 TJ
> '98 XJ
hoping ice didn't cook the module.
Someone else posted recently that the TJ also has some kind of gap that
allows ice to build up on the linkages. He had to remove the cowl cover
on the hood to get at it. (guessing that's where the motor is?)
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"M. E. Bye" wrote:
>
> Worst snow storm of the year going this morning and I go out to my TJ
> and discover that I don't have any wiper action. Fuse is good. What
> do y'all recommend as my next move? (P.S. Where is the wiper motor,
> anyway?)
>
> Thanks,
>
> Mark
> '98 TJ
> '98 XJ
Guest
Posts: n/a
Re: 98 Wrangler: No Wipers
I would try to gently pry them away from the frozen windshield while
hoping ice didn't cook the module.
Someone else posted recently that the TJ also has some kind of gap that
allows ice to build up on the linkages. He had to remove the cowl cover
on the hood to get at it. (guessing that's where the motor is?)
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"M. E. Bye" wrote:
>
> Worst snow storm of the year going this morning and I go out to my TJ
> and discover that I don't have any wiper action. Fuse is good. What
> do y'all recommend as my next move? (P.S. Where is the wiper motor,
> anyway?)
>
> Thanks,
>
> Mark
> '98 TJ
> '98 XJ
hoping ice didn't cook the module.
Someone else posted recently that the TJ also has some kind of gap that
allows ice to build up on the linkages. He had to remove the cowl cover
on the hood to get at it. (guessing that's where the motor is?)
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"M. E. Bye" wrote:
>
> Worst snow storm of the year going this morning and I go out to my TJ
> and discover that I don't have any wiper action. Fuse is good. What
> do y'all recommend as my next move? (P.S. Where is the wiper motor,
> anyway?)
>
> Thanks,
>
> Mark
> '98 TJ
> '98 XJ
Guest
Posts: n/a
Re: 98 Wrangler: No Wipers
I would try to gently pry them away from the frozen windshield while
hoping ice didn't cook the module.
Someone else posted recently that the TJ also has some kind of gap that
allows ice to build up on the linkages. He had to remove the cowl cover
on the hood to get at it. (guessing that's where the motor is?)
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"M. E. Bye" wrote:
>
> Worst snow storm of the year going this morning and I go out to my TJ
> and discover that I don't have any wiper action. Fuse is good. What
> do y'all recommend as my next move? (P.S. Where is the wiper motor,
> anyway?)
>
> Thanks,
>
> Mark
> '98 TJ
> '98 XJ
hoping ice didn't cook the module.
Someone else posted recently that the TJ also has some kind of gap that
allows ice to build up on the linkages. He had to remove the cowl cover
on the hood to get at it. (guessing that's where the motor is?)
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"M. E. Bye" wrote:
>
> Worst snow storm of the year going this morning and I go out to my TJ
> and discover that I don't have any wiper action. Fuse is good. What
> do y'all recommend as my next move? (P.S. Where is the wiper motor,
> anyway?)
>
> Thanks,
>
> Mark
> '98 TJ
> '98 XJ
Guest
Posts: n/a
Water on Floor (Was: 98 Wrangler: No Wipers)
On Mon, 20 Dec 2004 07:42:53 -0600, M. E. Bye <fxdyna@hotmail.com>
wrote:
>Worst snow storm of the year going this morning and I go out to my TJ
>and discover that I don't have any wiper action. Fuse is good. What
>do y'all recommend as my next move? (P.S. Where is the wiper motor,
>anyway?)
>
>Thanks,
>
>Mark
>'98 TJ
>'98 XJ
So... in below zero temperatures whilst replacing the wiper motor that
went ---- up on me last week during the worst winter storm so far this
year, I may have discovered (and hopefully cured) my "water on the
passenger floorboards" problem.
Once the cowl panel was off, I noticed that on the passenger side,
surrounding the fresh air intake, is a rather large "gasket" of foam
rubber. The foam on my TJ seemed to be unusually wet, quite a bit of
corrosion and debris around the screw/speed nut that secures the cowl
panel in that area. I cleaned it up as best I could and went to the
local hardware store and bought some foam weather stripping (the big
thick stuff you'd shove in around a window air conditioner). I ran a
bead of silicone adhesive and with the new weatherstrip, added an
additional layer that would be compressed a little tighter when I
re-installed the cowl panel.
Just passing this one along.
Mark
'98 TJ
'98 XJ
wrote:
>Worst snow storm of the year going this morning and I go out to my TJ
>and discover that I don't have any wiper action. Fuse is good. What
>do y'all recommend as my next move? (P.S. Where is the wiper motor,
>anyway?)
>
>Thanks,
>
>Mark
>'98 TJ
>'98 XJ
So... in below zero temperatures whilst replacing the wiper motor that
went ---- up on me last week during the worst winter storm so far this
year, I may have discovered (and hopefully cured) my "water on the
passenger floorboards" problem.
Once the cowl panel was off, I noticed that on the passenger side,
surrounding the fresh air intake, is a rather large "gasket" of foam
rubber. The foam on my TJ seemed to be unusually wet, quite a bit of
corrosion and debris around the screw/speed nut that secures the cowl
panel in that area. I cleaned it up as best I could and went to the
local hardware store and bought some foam weather stripping (the big
thick stuff you'd shove in around a window air conditioner). I ran a
bead of silicone adhesive and with the new weatherstrip, added an
additional layer that would be compressed a little tighter when I
re-installed the cowl panel.
Just passing this one along.
Mark
'98 TJ
'98 XJ
Guest
Posts: n/a
Water on Floor (Was: 98 Wrangler: No Wipers)
On Mon, 20 Dec 2004 07:42:53 -0600, M. E. Bye <fxdyna@hotmail.com>
wrote:
>Worst snow storm of the year going this morning and I go out to my TJ
>and discover that I don't have any wiper action. Fuse is good. What
>do y'all recommend as my next move? (P.S. Where is the wiper motor,
>anyway?)
>
>Thanks,
>
>Mark
>'98 TJ
>'98 XJ
So... in below zero temperatures whilst replacing the wiper motor that
went ---- up on me last week during the worst winter storm so far this
year, I may have discovered (and hopefully cured) my "water on the
passenger floorboards" problem.
Once the cowl panel was off, I noticed that on the passenger side,
surrounding the fresh air intake, is a rather large "gasket" of foam
rubber. The foam on my TJ seemed to be unusually wet, quite a bit of
corrosion and debris around the screw/speed nut that secures the cowl
panel in that area. I cleaned it up as best I could and went to the
local hardware store and bought some foam weather stripping (the big
thick stuff you'd shove in around a window air conditioner). I ran a
bead of silicone adhesive and with the new weatherstrip, added an
additional layer that would be compressed a little tighter when I
re-installed the cowl panel.
Just passing this one along.
Mark
'98 TJ
'98 XJ
wrote:
>Worst snow storm of the year going this morning and I go out to my TJ
>and discover that I don't have any wiper action. Fuse is good. What
>do y'all recommend as my next move? (P.S. Where is the wiper motor,
>anyway?)
>
>Thanks,
>
>Mark
>'98 TJ
>'98 XJ
So... in below zero temperatures whilst replacing the wiper motor that
went ---- up on me last week during the worst winter storm so far this
year, I may have discovered (and hopefully cured) my "water on the
passenger floorboards" problem.
Once the cowl panel was off, I noticed that on the passenger side,
surrounding the fresh air intake, is a rather large "gasket" of foam
rubber. The foam on my TJ seemed to be unusually wet, quite a bit of
corrosion and debris around the screw/speed nut that secures the cowl
panel in that area. I cleaned it up as best I could and went to the
local hardware store and bought some foam weather stripping (the big
thick stuff you'd shove in around a window air conditioner). I ran a
bead of silicone adhesive and with the new weatherstrip, added an
additional layer that would be compressed a little tighter when I
re-installed the cowl panel.
Just passing this one along.
Mark
'98 TJ
'98 XJ
Guest
Posts: n/a
Water on Floor (Was: 98 Wrangler: No Wipers)
On Mon, 20 Dec 2004 07:42:53 -0600, M. E. Bye <fxdyna@hotmail.com>
wrote:
>Worst snow storm of the year going this morning and I go out to my TJ
>and discover that I don't have any wiper action. Fuse is good. What
>do y'all recommend as my next move? (P.S. Where is the wiper motor,
>anyway?)
>
>Thanks,
>
>Mark
>'98 TJ
>'98 XJ
So... in below zero temperatures whilst replacing the wiper motor that
went ---- up on me last week during the worst winter storm so far this
year, I may have discovered (and hopefully cured) my "water on the
passenger floorboards" problem.
Once the cowl panel was off, I noticed that on the passenger side,
surrounding the fresh air intake, is a rather large "gasket" of foam
rubber. The foam on my TJ seemed to be unusually wet, quite a bit of
corrosion and debris around the screw/speed nut that secures the cowl
panel in that area. I cleaned it up as best I could and went to the
local hardware store and bought some foam weather stripping (the big
thick stuff you'd shove in around a window air conditioner). I ran a
bead of silicone adhesive and with the new weatherstrip, added an
additional layer that would be compressed a little tighter when I
re-installed the cowl panel.
Just passing this one along.
Mark
'98 TJ
'98 XJ
wrote:
>Worst snow storm of the year going this morning and I go out to my TJ
>and discover that I don't have any wiper action. Fuse is good. What
>do y'all recommend as my next move? (P.S. Where is the wiper motor,
>anyway?)
>
>Thanks,
>
>Mark
>'98 TJ
>'98 XJ
So... in below zero temperatures whilst replacing the wiper motor that
went ---- up on me last week during the worst winter storm so far this
year, I may have discovered (and hopefully cured) my "water on the
passenger floorboards" problem.
Once the cowl panel was off, I noticed that on the passenger side,
surrounding the fresh air intake, is a rather large "gasket" of foam
rubber. The foam on my TJ seemed to be unusually wet, quite a bit of
corrosion and debris around the screw/speed nut that secures the cowl
panel in that area. I cleaned it up as best I could and went to the
local hardware store and bought some foam weather stripping (the big
thick stuff you'd shove in around a window air conditioner). I ran a
bead of silicone adhesive and with the new weatherstrip, added an
additional layer that would be compressed a little tighter when I
re-installed the cowl panel.
Just passing this one along.
Mark
'98 TJ
'98 XJ
Guest
Posts: n/a
Re: Water on Floor (Was: 98 Wrangler: No Wipers)
Ahh man.....
Silicone is really bad news next to body metal. It outgasses fumes that
turn into acid when in contact with moisture and it 'will' rot out the
metal panel really fast. Totally rot it out.
You need to use a butyl compound around sheet metal.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"M. E. Bye" wrote:
>
> On Mon, 20 Dec 2004 07:42:53 -0600, M. E. Bye <fxdyna@hotmail.com>
> wrote:
>
> >Worst snow storm of the year going this morning and I go out to my TJ
> >and discover that I don't have any wiper action. Fuse is good. What
> >do y'all recommend as my next move? (P.S. Where is the wiper motor,
> >anyway?)
> >
> >Thanks,
> >
> >Mark
> >'98 TJ
> >'98 XJ
>
> So... in below zero temperatures whilst replacing the wiper motor that
> went ---- up on me last week during the worst winter storm so far this
> year, I may have discovered (and hopefully cured) my "water on the
> passenger floorboards" problem.
>
> Once the cowl panel was off, I noticed that on the passenger side,
> surrounding the fresh air intake, is a rather large "gasket" of foam
> rubber. The foam on my TJ seemed to be unusually wet, quite a bit of
> corrosion and debris around the screw/speed nut that secures the cowl
> panel in that area. I cleaned it up as best I could and went to the
> local hardware store and bought some foam weather stripping (the big
> thick stuff you'd shove in around a window air conditioner). I ran a
> bead of silicone adhesive and with the new weatherstrip, added an
> additional layer that would be compressed a little tighter when I
> re-installed the cowl panel.
>
> Just passing this one along.
>
> Mark
> '98 TJ
> '98 XJ
Silicone is really bad news next to body metal. It outgasses fumes that
turn into acid when in contact with moisture and it 'will' rot out the
metal panel really fast. Totally rot it out.
You need to use a butyl compound around sheet metal.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"M. E. Bye" wrote:
>
> On Mon, 20 Dec 2004 07:42:53 -0600, M. E. Bye <fxdyna@hotmail.com>
> wrote:
>
> >Worst snow storm of the year going this morning and I go out to my TJ
> >and discover that I don't have any wiper action. Fuse is good. What
> >do y'all recommend as my next move? (P.S. Where is the wiper motor,
> >anyway?)
> >
> >Thanks,
> >
> >Mark
> >'98 TJ
> >'98 XJ
>
> So... in below zero temperatures whilst replacing the wiper motor that
> went ---- up on me last week during the worst winter storm so far this
> year, I may have discovered (and hopefully cured) my "water on the
> passenger floorboards" problem.
>
> Once the cowl panel was off, I noticed that on the passenger side,
> surrounding the fresh air intake, is a rather large "gasket" of foam
> rubber. The foam on my TJ seemed to be unusually wet, quite a bit of
> corrosion and debris around the screw/speed nut that secures the cowl
> panel in that area. I cleaned it up as best I could and went to the
> local hardware store and bought some foam weather stripping (the big
> thick stuff you'd shove in around a window air conditioner). I ran a
> bead of silicone adhesive and with the new weatherstrip, added an
> additional layer that would be compressed a little tighter when I
> re-installed the cowl panel.
>
> Just passing this one along.
>
> Mark
> '98 TJ
> '98 XJ
Guest
Posts: n/a
Re: Water on Floor (Was: 98 Wrangler: No Wipers)
Ahh man.....
Silicone is really bad news next to body metal. It outgasses fumes that
turn into acid when in contact with moisture and it 'will' rot out the
metal panel really fast. Totally rot it out.
You need to use a butyl compound around sheet metal.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"M. E. Bye" wrote:
>
> On Mon, 20 Dec 2004 07:42:53 -0600, M. E. Bye <fxdyna@hotmail.com>
> wrote:
>
> >Worst snow storm of the year going this morning and I go out to my TJ
> >and discover that I don't have any wiper action. Fuse is good. What
> >do y'all recommend as my next move? (P.S. Where is the wiper motor,
> >anyway?)
> >
> >Thanks,
> >
> >Mark
> >'98 TJ
> >'98 XJ
>
> So... in below zero temperatures whilst replacing the wiper motor that
> went ---- up on me last week during the worst winter storm so far this
> year, I may have discovered (and hopefully cured) my "water on the
> passenger floorboards" problem.
>
> Once the cowl panel was off, I noticed that on the passenger side,
> surrounding the fresh air intake, is a rather large "gasket" of foam
> rubber. The foam on my TJ seemed to be unusually wet, quite a bit of
> corrosion and debris around the screw/speed nut that secures the cowl
> panel in that area. I cleaned it up as best I could and went to the
> local hardware store and bought some foam weather stripping (the big
> thick stuff you'd shove in around a window air conditioner). I ran a
> bead of silicone adhesive and with the new weatherstrip, added an
> additional layer that would be compressed a little tighter when I
> re-installed the cowl panel.
>
> Just passing this one along.
>
> Mark
> '98 TJ
> '98 XJ
Silicone is really bad news next to body metal. It outgasses fumes that
turn into acid when in contact with moisture and it 'will' rot out the
metal panel really fast. Totally rot it out.
You need to use a butyl compound around sheet metal.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"M. E. Bye" wrote:
>
> On Mon, 20 Dec 2004 07:42:53 -0600, M. E. Bye <fxdyna@hotmail.com>
> wrote:
>
> >Worst snow storm of the year going this morning and I go out to my TJ
> >and discover that I don't have any wiper action. Fuse is good. What
> >do y'all recommend as my next move? (P.S. Where is the wiper motor,
> >anyway?)
> >
> >Thanks,
> >
> >Mark
> >'98 TJ
> >'98 XJ
>
> So... in below zero temperatures whilst replacing the wiper motor that
> went ---- up on me last week during the worst winter storm so far this
> year, I may have discovered (and hopefully cured) my "water on the
> passenger floorboards" problem.
>
> Once the cowl panel was off, I noticed that on the passenger side,
> surrounding the fresh air intake, is a rather large "gasket" of foam
> rubber. The foam on my TJ seemed to be unusually wet, quite a bit of
> corrosion and debris around the screw/speed nut that secures the cowl
> panel in that area. I cleaned it up as best I could and went to the
> local hardware store and bought some foam weather stripping (the big
> thick stuff you'd shove in around a window air conditioner). I ran a
> bead of silicone adhesive and with the new weatherstrip, added an
> additional layer that would be compressed a little tighter when I
> re-installed the cowl panel.
>
> Just passing this one along.
>
> Mark
> '98 TJ
> '98 XJ
Guest
Posts: n/a
Re: Water on Floor (Was: 98 Wrangler: No Wipers)
Ahh man.....
Silicone is really bad news next to body metal. It outgasses fumes that
turn into acid when in contact with moisture and it 'will' rot out the
metal panel really fast. Totally rot it out.
You need to use a butyl compound around sheet metal.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"M. E. Bye" wrote:
>
> On Mon, 20 Dec 2004 07:42:53 -0600, M. E. Bye <fxdyna@hotmail.com>
> wrote:
>
> >Worst snow storm of the year going this morning and I go out to my TJ
> >and discover that I don't have any wiper action. Fuse is good. What
> >do y'all recommend as my next move? (P.S. Where is the wiper motor,
> >anyway?)
> >
> >Thanks,
> >
> >Mark
> >'98 TJ
> >'98 XJ
>
> So... in below zero temperatures whilst replacing the wiper motor that
> went ---- up on me last week during the worst winter storm so far this
> year, I may have discovered (and hopefully cured) my "water on the
> passenger floorboards" problem.
>
> Once the cowl panel was off, I noticed that on the passenger side,
> surrounding the fresh air intake, is a rather large "gasket" of foam
> rubber. The foam on my TJ seemed to be unusually wet, quite a bit of
> corrosion and debris around the screw/speed nut that secures the cowl
> panel in that area. I cleaned it up as best I could and went to the
> local hardware store and bought some foam weather stripping (the big
> thick stuff you'd shove in around a window air conditioner). I ran a
> bead of silicone adhesive and with the new weatherstrip, added an
> additional layer that would be compressed a little tighter when I
> re-installed the cowl panel.
>
> Just passing this one along.
>
> Mark
> '98 TJ
> '98 XJ
Silicone is really bad news next to body metal. It outgasses fumes that
turn into acid when in contact with moisture and it 'will' rot out the
metal panel really fast. Totally rot it out.
You need to use a butyl compound around sheet metal.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"M. E. Bye" wrote:
>
> On Mon, 20 Dec 2004 07:42:53 -0600, M. E. Bye <fxdyna@hotmail.com>
> wrote:
>
> >Worst snow storm of the year going this morning and I go out to my TJ
> >and discover that I don't have any wiper action. Fuse is good. What
> >do y'all recommend as my next move? (P.S. Where is the wiper motor,
> >anyway?)
> >
> >Thanks,
> >
> >Mark
> >'98 TJ
> >'98 XJ
>
> So... in below zero temperatures whilst replacing the wiper motor that
> went ---- up on me last week during the worst winter storm so far this
> year, I may have discovered (and hopefully cured) my "water on the
> passenger floorboards" problem.
>
> Once the cowl panel was off, I noticed that on the passenger side,
> surrounding the fresh air intake, is a rather large "gasket" of foam
> rubber. The foam on my TJ seemed to be unusually wet, quite a bit of
> corrosion and debris around the screw/speed nut that secures the cowl
> panel in that area. I cleaned it up as best I could and went to the
> local hardware store and bought some foam weather stripping (the big
> thick stuff you'd shove in around a window air conditioner). I ran a
> bead of silicone adhesive and with the new weatherstrip, added an
> additional layer that would be compressed a little tighter when I
> re-installed the cowl panel.
>
> Just passing this one along.
>
> Mark
> '98 TJ
> '98 XJ