95 XJ rocker panels
03-24-2005, 06:58 PM
#11
Guest
Posts: n/a
Re: 95 XJ rocker panels
I have seen them just plain cut out. It looked a bit strange but they
are just a box hanging below the door anyway, the inside box is it's own
animal.
I like the 6"x2" tube idea, that would stiffen it up a lot too I would
think.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Snow wrote:
>
> Look around you can find replacement panels for as little as $60 per side.
> They do require trimming and complete removal of the old ones, you will also
> have to remove the fender flares runningboards if you have them. I just
> used some light gauge sheet metal I already had (left overs from doing my
> floors) to form more of a cover, I removed about 90% of the old rocker (85%
> was rusted out).
>
> Snow...
>
> "TF" <flannery16@insightbb.com> wrote in message
> news:gHG0e.16081$fn3.14775@attbi_s01...
> > Anyone replaced rusted out rocker panels?
> > Any tips or where to buy both sides?
> > Replaced floor on pass side now for this.....
> >
> > Thanks
> >
are just a box hanging below the door anyway, the inside box is it's own
animal.
I like the 6"x2" tube idea, that would stiffen it up a lot too I would
think.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Snow wrote:
>
> Look around you can find replacement panels for as little as $60 per side.
> They do require trimming and complete removal of the old ones, you will also
> have to remove the fender flares runningboards if you have them. I just
> used some light gauge sheet metal I already had (left overs from doing my
> floors) to form more of a cover, I removed about 90% of the old rocker (85%
> was rusted out).
>
> Snow...
>
> "TF" <flannery16@insightbb.com> wrote in message
> news:gHG0e.16081$fn3.14775@attbi_s01...
> > Anyone replaced rusted out rocker panels?
> > Any tips or where to buy both sides?
> > Replaced floor on pass side now for this.....
> >
> > Thanks
> >
03-24-2005, 06:58 PM
#12
Guest
Posts: n/a
Re: 95 XJ rocker panels
I have seen them just plain cut out. It looked a bit strange but they
are just a box hanging below the door anyway, the inside box is it's own
animal.
I like the 6"x2" tube idea, that would stiffen it up a lot too I would
think.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Snow wrote:
>
> Look around you can find replacement panels for as little as $60 per side.
> They do require trimming and complete removal of the old ones, you will also
> have to remove the fender flares runningboards if you have them. I just
> used some light gauge sheet metal I already had (left overs from doing my
> floors) to form more of a cover, I removed about 90% of the old rocker (85%
> was rusted out).
>
> Snow...
>
> "TF" <flannery16@insightbb.com> wrote in message
> news:gHG0e.16081$fn3.14775@attbi_s01...
> > Anyone replaced rusted out rocker panels?
> > Any tips or where to buy both sides?
> > Replaced floor on pass side now for this.....
> >
> > Thanks
> >
are just a box hanging below the door anyway, the inside box is it's own
animal.
I like the 6"x2" tube idea, that would stiffen it up a lot too I would
think.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Snow wrote:
>
> Look around you can find replacement panels for as little as $60 per side.
> They do require trimming and complete removal of the old ones, you will also
> have to remove the fender flares runningboards if you have them. I just
> used some light gauge sheet metal I already had (left overs from doing my
> floors) to form more of a cover, I removed about 90% of the old rocker (85%
> was rusted out).
>
> Snow...
>
> "TF" <flannery16@insightbb.com> wrote in message
> news:gHG0e.16081$fn3.14775@attbi_s01...
> > Anyone replaced rusted out rocker panels?
> > Any tips or where to buy both sides?
> > Replaced floor on pass side now for this.....
> >
> > Thanks
> >
03-24-2005, 06:58 PM
#13
Guest
Posts: n/a
Re: 95 XJ rocker panels
I have seen them just plain cut out. It looked a bit strange but they
are just a box hanging below the door anyway, the inside box is it's own
animal.
I like the 6"x2" tube idea, that would stiffen it up a lot too I would
think.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Snow wrote:
>
> Look around you can find replacement panels for as little as $60 per side.
> They do require trimming and complete removal of the old ones, you will also
> have to remove the fender flares runningboards if you have them. I just
> used some light gauge sheet metal I already had (left overs from doing my
> floors) to form more of a cover, I removed about 90% of the old rocker (85%
> was rusted out).
>
> Snow...
>
> "TF" <flannery16@insightbb.com> wrote in message
> news:gHG0e.16081$fn3.14775@attbi_s01...
> > Anyone replaced rusted out rocker panels?
> > Any tips or where to buy both sides?
> > Replaced floor on pass side now for this.....
> >
> > Thanks
> >
are just a box hanging below the door anyway, the inside box is it's own
animal.
I like the 6"x2" tube idea, that would stiffen it up a lot too I would
think.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Snow wrote:
>
> Look around you can find replacement panels for as little as $60 per side.
> They do require trimming and complete removal of the old ones, you will also
> have to remove the fender flares runningboards if you have them. I just
> used some light gauge sheet metal I already had (left overs from doing my
> floors) to form more of a cover, I removed about 90% of the old rocker (85%
> was rusted out).
>
> Snow...
>
> "TF" <flannery16@insightbb.com> wrote in message
> news:gHG0e.16081$fn3.14775@attbi_s01...
> > Anyone replaced rusted out rocker panels?
> > Any tips or where to buy both sides?
> > Replaced floor on pass side now for this.....
> >
> > Thanks
> >
03-25-2005, 08:01 AM
#14
Guest
Posts: n/a
Re: 95 XJ rocker panels
I just got a set of rocker panels for my 1989 Jeep Cherokee Laredo from this
site. Might have what your looking for.
www.crosscanadaparts.com
Sign in as a guest to look around the online Catalog.
"TF" <flannery16@insightbb.com> wrote in message
news:gHG0e.16081$fn3.14775@attbi_s01...
> Anyone replaced rusted out rocker panels?
> Any tips or where to buy both sides?
> Replaced floor on pass side now for this.....
>
> Thanks
>
>
site. Might have what your looking for.
www.crosscanadaparts.com
Sign in as a guest to look around the online Catalog.
"TF" <flannery16@insightbb.com> wrote in message
news:gHG0e.16081$fn3.14775@attbi_s01...
> Anyone replaced rusted out rocker panels?
> Any tips or where to buy both sides?
> Replaced floor on pass side now for this.....
>
> Thanks
>
>
03-25-2005, 08:01 AM
#15
Guest
Posts: n/a
Re: 95 XJ rocker panels
I just got a set of rocker panels for my 1989 Jeep Cherokee Laredo from this
site. Might have what your looking for.
www.crosscanadaparts.com
Sign in as a guest to look around the online Catalog.
"TF" <flannery16@insightbb.com> wrote in message
news:gHG0e.16081$fn3.14775@attbi_s01...
> Anyone replaced rusted out rocker panels?
> Any tips or where to buy both sides?
> Replaced floor on pass side now for this.....
>
> Thanks
>
>
site. Might have what your looking for.
www.crosscanadaparts.com
Sign in as a guest to look around the online Catalog.
"TF" <flannery16@insightbb.com> wrote in message
news:gHG0e.16081$fn3.14775@attbi_s01...
> Anyone replaced rusted out rocker panels?
> Any tips or where to buy both sides?
> Replaced floor on pass side now for this.....
>
> Thanks
>
>
03-25-2005, 08:01 AM
#16
Guest
Posts: n/a
Re: 95 XJ rocker panels
I just got a set of rocker panels for my 1989 Jeep Cherokee Laredo from this
site. Might have what your looking for.
www.crosscanadaparts.com
Sign in as a guest to look around the online Catalog.
"TF" <flannery16@insightbb.com> wrote in message
news:gHG0e.16081$fn3.14775@attbi_s01...
> Anyone replaced rusted out rocker panels?
> Any tips or where to buy both sides?
> Replaced floor on pass side now for this.....
>
> Thanks
>
>
site. Might have what your looking for.
www.crosscanadaparts.com
Sign in as a guest to look around the online Catalog.
"TF" <flannery16@insightbb.com> wrote in message
news:gHG0e.16081$fn3.14775@attbi_s01...
> Anyone replaced rusted out rocker panels?
> Any tips or where to buy both sides?
> Replaced floor on pass side now for this.....
>
> Thanks
>
>
03-25-2005, 09:00 AM
#17
Guest
Posts: n/a
Re: 95 XJ rocker panels
If my XJ survives its next smog test (next year) I'll do the box tubing
thing, I really just needed to cover up the huge hole from rear dog leg to
middle of drivers door. It was real obvious and seeing how I run a few 400
series highways I've seen the cops/MTO pulling quickie safety blitz's and
since the inside of the rocker has lightening holes into the cab (back of
the carpet) I knew if I got pulled into one of those I would get 72 hours to
fix warnings. Also at the time my exhaust was almost non existent from
the cat back.
Snow...
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:42435409.175F776F@sympatico.ca...
>I have seen them just plain cut out. It looked a bit strange but they
> are just a box hanging below the door anyway, the inside box is it's own
> animal.
>
> I like the 6"x2" tube idea, that would stiffen it up a lot too I would
> think.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Snow wrote:
>>
>> Look around you can find replacement panels for as little as $60 per
>> side.
>> They do require trimming and complete removal of the old ones, you will
>> also
>> have to remove the fender flares runningboards if you have them. I just
>> used some light gauge sheet metal I already had (left overs from doing my
>> floors) to form more of a cover, I removed about 90% of the old rocker
>> (85%
>> was rusted out).
>>
>> Snow...
>>
>> "TF" <flannery16@insightbb.com> wrote in message
>> news:gHG0e.16081$fn3.14775@attbi_s01...
>> > Anyone replaced rusted out rocker panels?
>> > Any tips or where to buy both sides?
>> > Replaced floor on pass side now for this.....
>> >
>> > Thanks
>> >
thing, I really just needed to cover up the huge hole from rear dog leg to
middle of drivers door. It was real obvious and seeing how I run a few 400
series highways I've seen the cops/MTO pulling quickie safety blitz's and
since the inside of the rocker has lightening holes into the cab (back of
the carpet) I knew if I got pulled into one of those I would get 72 hours to
fix warnings. Also at the time my exhaust was almost non existent from
the cat back.
Snow...
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:42435409.175F776F@sympatico.ca...
>I have seen them just plain cut out. It looked a bit strange but they
> are just a box hanging below the door anyway, the inside box is it's own
> animal.
>
> I like the 6"x2" tube idea, that would stiffen it up a lot too I would
> think.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Snow wrote:
>>
>> Look around you can find replacement panels for as little as $60 per
>> side.
>> They do require trimming and complete removal of the old ones, you will
>> also
>> have to remove the fender flares runningboards if you have them. I just
>> used some light gauge sheet metal I already had (left overs from doing my
>> floors) to form more of a cover, I removed about 90% of the old rocker
>> (85%
>> was rusted out).
>>
>> Snow...
>>
>> "TF" <flannery16@insightbb.com> wrote in message
>> news:gHG0e.16081$fn3.14775@attbi_s01...
>> > Anyone replaced rusted out rocker panels?
>> > Any tips or where to buy both sides?
>> > Replaced floor on pass side now for this.....
>> >
>> > Thanks
>> >
03-25-2005, 09:00 AM
#18
Guest
Posts: n/a
Re: 95 XJ rocker panels
If my XJ survives its next smog test (next year) I'll do the box tubing
thing, I really just needed to cover up the huge hole from rear dog leg to
middle of drivers door. It was real obvious and seeing how I run a few 400
series highways I've seen the cops/MTO pulling quickie safety blitz's and
since the inside of the rocker has lightening holes into the cab (back of
the carpet) I knew if I got pulled into one of those I would get 72 hours to
fix warnings. Also at the time my exhaust was almost non existent from
the cat back.
Snow...
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:42435409.175F776F@sympatico.ca...
>I have seen them just plain cut out. It looked a bit strange but they
> are just a box hanging below the door anyway, the inside box is it's own
> animal.
>
> I like the 6"x2" tube idea, that would stiffen it up a lot too I would
> think.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Snow wrote:
>>
>> Look around you can find replacement panels for as little as $60 per
>> side.
>> They do require trimming and complete removal of the old ones, you will
>> also
>> have to remove the fender flares runningboards if you have them. I just
>> used some light gauge sheet metal I already had (left overs from doing my
>> floors) to form more of a cover, I removed about 90% of the old rocker
>> (85%
>> was rusted out).
>>
>> Snow...
>>
>> "TF" <flannery16@insightbb.com> wrote in message
>> news:gHG0e.16081$fn3.14775@attbi_s01...
>> > Anyone replaced rusted out rocker panels?
>> > Any tips or where to buy both sides?
>> > Replaced floor on pass side now for this.....
>> >
>> > Thanks
>> >
thing, I really just needed to cover up the huge hole from rear dog leg to
middle of drivers door. It was real obvious and seeing how I run a few 400
series highways I've seen the cops/MTO pulling quickie safety blitz's and
since the inside of the rocker has lightening holes into the cab (back of
the carpet) I knew if I got pulled into one of those I would get 72 hours to
fix warnings. Also at the time my exhaust was almost non existent from
the cat back.
Snow...
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:42435409.175F776F@sympatico.ca...
>I have seen them just plain cut out. It looked a bit strange but they
> are just a box hanging below the door anyway, the inside box is it's own
> animal.
>
> I like the 6"x2" tube idea, that would stiffen it up a lot too I would
> think.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Snow wrote:
>>
>> Look around you can find replacement panels for as little as $60 per
>> side.
>> They do require trimming and complete removal of the old ones, you will
>> also
>> have to remove the fender flares runningboards if you have them. I just
>> used some light gauge sheet metal I already had (left overs from doing my
>> floors) to form more of a cover, I removed about 90% of the old rocker
>> (85%
>> was rusted out).
>>
>> Snow...
>>
>> "TF" <flannery16@insightbb.com> wrote in message
>> news:gHG0e.16081$fn3.14775@attbi_s01...
>> > Anyone replaced rusted out rocker panels?
>> > Any tips or where to buy both sides?
>> > Replaced floor on pass side now for this.....
>> >
>> > Thanks
>> >
03-25-2005, 09:00 AM
#19
Guest
Posts: n/a
Re: 95 XJ rocker panels
If my XJ survives its next smog test (next year) I'll do the box tubing
thing, I really just needed to cover up the huge hole from rear dog leg to
middle of drivers door. It was real obvious and seeing how I run a few 400
series highways I've seen the cops/MTO pulling quickie safety blitz's and
since the inside of the rocker has lightening holes into the cab (back of
the carpet) I knew if I got pulled into one of those I would get 72 hours to
fix warnings. Also at the time my exhaust was almost non existent from
the cat back.
Snow...
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:42435409.175F776F@sympatico.ca...
>I have seen them just plain cut out. It looked a bit strange but they
> are just a box hanging below the door anyway, the inside box is it's own
> animal.
>
> I like the 6"x2" tube idea, that would stiffen it up a lot too I would
> think.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Snow wrote:
>>
>> Look around you can find replacement panels for as little as $60 per
>> side.
>> They do require trimming and complete removal of the old ones, you will
>> also
>> have to remove the fender flares runningboards if you have them. I just
>> used some light gauge sheet metal I already had (left overs from doing my
>> floors) to form more of a cover, I removed about 90% of the old rocker
>> (85%
>> was rusted out).
>>
>> Snow...
>>
>> "TF" <flannery16@insightbb.com> wrote in message
>> news:gHG0e.16081$fn3.14775@attbi_s01...
>> > Anyone replaced rusted out rocker panels?
>> > Any tips or where to buy both sides?
>> > Replaced floor on pass side now for this.....
>> >
>> > Thanks
>> >
thing, I really just needed to cover up the huge hole from rear dog leg to
middle of drivers door. It was real obvious and seeing how I run a few 400
series highways I've seen the cops/MTO pulling quickie safety blitz's and
since the inside of the rocker has lightening holes into the cab (back of
the carpet) I knew if I got pulled into one of those I would get 72 hours to
fix warnings. Also at the time my exhaust was almost non existent from
the cat back.
Snow...
"Mike Romain" <romainm@sympatico.ca> wrote in message
news:42435409.175F776F@sympatico.ca...
>I have seen them just plain cut out. It looked a bit strange but they
> are just a box hanging below the door anyway, the inside box is it's own
> animal.
>
> I like the 6"x2" tube idea, that would stiffen it up a lot too I would
> think.
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Snow wrote:
>>
>> Look around you can find replacement panels for as little as $60 per
>> side.
>> They do require trimming and complete removal of the old ones, you will
>> also
>> have to remove the fender flares runningboards if you have them. I just
>> used some light gauge sheet metal I already had (left overs from doing my
>> floors) to form more of a cover, I removed about 90% of the old rocker
>> (85%
>> was rusted out).
>>
>> Snow...
>>
>> "TF" <flannery16@insightbb.com> wrote in message
>> news:gHG0e.16081$fn3.14775@attbi_s01...
>> > Anyone replaced rusted out rocker panels?
>> > Any tips or where to buy both sides?
>> > Replaced floor on pass side now for this.....
>> >
>> > Thanks
>> >
03-25-2005, 09:02 AM
#20
Guest
Posts: n/a
Re: 95 XJ rocker panels
That's who I looked at for replacements, I know of a small parts store that
deals with them and can pick up dent and dings for 30-65% off. A gent at
work replaced every body panel on his ford truck with dent and dings from
them for a total of about $350.
Snow...
"k_902" <kyled@pei.sympatico.ca> wrote in message
news:nYT0e.4655$Ln.216141@ursa-nb00s0.nbnet.nb.ca...
>I just got a set of rocker panels for my 1989 Jeep Cherokee Laredo from
>this
> site. Might have what your looking for.
>
> www.crosscanadaparts.com
>
> Sign in as a guest to look around the online Catalog.
>
>
> "TF" <flannery16@insightbb.com> wrote in message
> news:gHG0e.16081$fn3.14775@attbi_s01...
>> Anyone replaced rusted out rocker panels?
>> Any tips or where to buy both sides?
>> Replaced floor on pass side now for this.....
>>
>> Thanks
>>
>>
>
>
deals with them and can pick up dent and dings for 30-65% off. A gent at
work replaced every body panel on his ford truck with dent and dings from
them for a total of about $350.
Snow...
"k_902" <kyled@pei.sympatico.ca> wrote in message
news:nYT0e.4655$Ln.216141@ursa-nb00s0.nbnet.nb.ca...
>I just got a set of rocker panels for my 1989 Jeep Cherokee Laredo from
>this
> site. Might have what your looking for.
>
> www.crosscanadaparts.com
>
> Sign in as a guest to look around the online Catalog.
>
>
> "TF" <flannery16@insightbb.com> wrote in message
> news:gHG0e.16081$fn3.14775@attbi_s01...
>> Anyone replaced rusted out rocker panels?
>> Any tips or where to buy both sides?
>> Replaced floor on pass side now for this.....
>>
>> Thanks
>>
>>
>
>