94 yj xfer case not engaging front axle
04-03-2005, 04:57 PM
#1
Guest
Posts: n/a
94 yj xfer case not engaging front axle
Yesterday found out the hard way I don't have 4wd. Today checked front axle
vacuum motor and found it engages. With all four wheels off the ground I
engaged 4L and put transmission in gear. While the rear wheels spun the
front wheels do not spin. I notice the front drive shaft was slowly
rotating, but I cound easily stop it with by hand. Same results for 4H. I
adjusted the linkage just to be sure.
I have the np231 J xfer case. Is the xfer case bad? Is there a possible
simple fix or do I replace it with a rebuilt? Is there a suggested upgrade?
I just mess around on the back roads in Big Bear area.
vacuum motor and found it engages. With all four wheels off the ground I
engaged 4L and put transmission in gear. While the rear wheels spun the
front wheels do not spin. I notice the front drive shaft was slowly
rotating, but I cound easily stop it with by hand. Same results for 4H. I
adjusted the linkage just to be sure.
I have the np231 J xfer case. Is the xfer case bad? Is there a possible
simple fix or do I replace it with a rebuilt? Is there a suggested upgrade?
I just mess around on the back roads in Big Bear area.
04-05-2005, 09:04 AM
#2
Guest
Posts: n/a
Re: 94 yj xfer case not engaging front axle
Is this not making it to the news group or is there no comment worth
posting?
"Marvin Oliver" <m3599137@earthlink.net> wrote in message
news:EMY3e.4610$x4.717@newsread1.news.pas.earthlin k.net...
> Yesterday found out the hard way I don't have 4wd. Today checked front
> axle vacuum motor and found it engages. With all four wheels off the
> ground I engaged 4L and put transmission in gear. While the rear wheels
> spun the front wheels do not spin. I notice the front drive shaft was
> slowly rotating, but I cound easily stop it with by hand. Same results for
> 4H. I adjusted the linkage just to be sure.
>
> I have the np231 J xfer case. Is the xfer case bad? Is there a possible
> simple fix or do I replace it with a rebuilt? Is there a suggested
> upgrade? I just mess around on the back roads in Big Bear area.
>
posting?
"Marvin Oliver" <m3599137@earthlink.net> wrote in message
news:EMY3e.4610$x4.717@newsread1.news.pas.earthlin k.net...
> Yesterday found out the hard way I don't have 4wd. Today checked front
> axle vacuum motor and found it engages. With all four wheels off the
> ground I engaged 4L and put transmission in gear. While the rear wheels
> spun the front wheels do not spin. I notice the front drive shaft was
> slowly rotating, but I cound easily stop it with by hand. Same results for
> 4H. I adjusted the linkage just to be sure.
>
> I have the np231 J xfer case. Is the xfer case bad? Is there a possible
> simple fix or do I replace it with a rebuilt? Is there a suggested
> upgrade? I just mess around on the back roads in Big Bear area.
>
04-05-2005, 09:04 AM
#3
Guest
Posts: n/a
Re: 94 yj xfer case not engaging front axle
Is this not making it to the news group or is there no comment worth
posting?
"Marvin Oliver" <m3599137@earthlink.net> wrote in message
news:EMY3e.4610$x4.717@newsread1.news.pas.earthlin k.net...
> Yesterday found out the hard way I don't have 4wd. Today checked front
> axle vacuum motor and found it engages. With all four wheels off the
> ground I engaged 4L and put transmission in gear. While the rear wheels
> spun the front wheels do not spin. I notice the front drive shaft was
> slowly rotating, but I cound easily stop it with by hand. Same results for
> 4H. I adjusted the linkage just to be sure.
>
> I have the np231 J xfer case. Is the xfer case bad? Is there a possible
> simple fix or do I replace it with a rebuilt? Is there a suggested
> upgrade? I just mess around on the back roads in Big Bear area.
>
posting?
"Marvin Oliver" <m3599137@earthlink.net> wrote in message
news:EMY3e.4610$x4.717@newsread1.news.pas.earthlin k.net...
> Yesterday found out the hard way I don't have 4wd. Today checked front
> axle vacuum motor and found it engages. With all four wheels off the
> ground I engaged 4L and put transmission in gear. While the rear wheels
> spun the front wheels do not spin. I notice the front drive shaft was
> slowly rotating, but I cound easily stop it with by hand. Same results for
> 4H. I adjusted the linkage just to be sure.
>
> I have the np231 J xfer case. Is the xfer case bad? Is there a possible
> simple fix or do I replace it with a rebuilt? Is there a suggested
> upgrade? I just mess around on the back roads in Big Bear area.
>
04-05-2005, 09:04 AM
#4
Guest
Posts: n/a
Re: 94 yj xfer case not engaging front axle
Is this not making it to the news group or is there no comment worth
posting?
"Marvin Oliver" <m3599137@earthlink.net> wrote in message
news:EMY3e.4610$x4.717@newsread1.news.pas.earthlin k.net...
> Yesterday found out the hard way I don't have 4wd. Today checked front
> axle vacuum motor and found it engages. With all four wheels off the
> ground I engaged 4L and put transmission in gear. While the rear wheels
> spun the front wheels do not spin. I notice the front drive shaft was
> slowly rotating, but I cound easily stop it with by hand. Same results for
> 4H. I adjusted the linkage just to be sure.
>
> I have the np231 J xfer case. Is the xfer case bad? Is there a possible
> simple fix or do I replace it with a rebuilt? Is there a suggested
> upgrade? I just mess around on the back roads in Big Bear area.
>
posting?
"Marvin Oliver" <m3599137@earthlink.net> wrote in message
news:EMY3e.4610$x4.717@newsread1.news.pas.earthlin k.net...
> Yesterday found out the hard way I don't have 4wd. Today checked front
> axle vacuum motor and found it engages. With all four wheels off the
> ground I engaged 4L and put transmission in gear. While the rear wheels
> spun the front wheels do not spin. I notice the front drive shaft was
> slowly rotating, but I cound easily stop it with by hand. Same results for
> 4H. I adjusted the linkage just to be sure.
>
> I have the np231 J xfer case. Is the xfer case bad? Is there a possible
> simple fix or do I replace it with a rebuilt? Is there a suggested
> upgrade? I just mess around on the back roads in Big Bear area.
>
04-05-2005, 09:04 AM
#5
Guest
Posts: n/a
Re: 94 yj xfer case not engaging front axle
Is this not making it to the news group or is there no comment worth
posting?
"Marvin Oliver" <m3599137@earthlink.net> wrote in message
news:EMY3e.4610$x4.717@newsread1.news.pas.earthlin k.net...
> Yesterday found out the hard way I don't have 4wd. Today checked front
> axle vacuum motor and found it engages. With all four wheels off the
> ground I engaged 4L and put transmission in gear. While the rear wheels
> spun the front wheels do not spin. I notice the front drive shaft was
> slowly rotating, but I cound easily stop it with by hand. Same results for
> 4H. I adjusted the linkage just to be sure.
>
> I have the np231 J xfer case. Is the xfer case bad? Is there a possible
> simple fix or do I replace it with a rebuilt? Is there a suggested
> upgrade? I just mess around on the back roads in Big Bear area.
>
posting?
"Marvin Oliver" <m3599137@earthlink.net> wrote in message
news:EMY3e.4610$x4.717@newsread1.news.pas.earthlin k.net...
> Yesterday found out the hard way I don't have 4wd. Today checked front
> axle vacuum motor and found it engages. With all four wheels off the
> ground I engaged 4L and put transmission in gear. While the rear wheels
> spun the front wheels do not spin. I notice the front drive shaft was
> slowly rotating, but I cound easily stop it with by hand. Same results for
> 4H. I adjusted the linkage just to be sure.
>
> I have the np231 J xfer case. Is the xfer case bad? Is there a possible
> simple fix or do I replace it with a rebuilt? Is there a suggested
> upgrade? I just mess around on the back roads in Big Bear area.
>
04-05-2005, 09:30 AM
#6
Guest
Posts: n/a
Re: 94 yj xfer case not engaging front axle
No one really had the heart to tell you what you already have figured
likely....
That t-case was a chain drive one so at the 'best' you are looking at a
new chain and sprockets.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Marvin Oliver wrote:
>
> Is this not making it to the news group or is there no comment worth
> posting?
>
> "Marvin Oliver" <m3599137@earthlink.net> wrote in message
> news:EMY3e.4610$x4.717@newsread1.news.pas.earthlin k.net...
>
> > Yesterday found out the hard way I don't have 4wd. Today checked front
> > axle vacuum motor and found it engages. With all four wheels off the
> > ground I engaged 4L and put transmission in gear. While the rear wheels
> > spun the front wheels do not spin. I notice the front drive shaft was
> > slowly rotating, but I cound easily stop it with by hand. Same results for
> > 4H. I adjusted the linkage just to be sure.
> >
> > I have the np231 J xfer case. Is the xfer case bad? Is there a possible
> > simple fix or do I replace it with a rebuilt? Is there a suggested
> > upgrade? I just mess around on the back roads in Big Bear area.
> >
likely....
That t-case was a chain drive one so at the 'best' you are looking at a
new chain and sprockets.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Marvin Oliver wrote:
>
> Is this not making it to the news group or is there no comment worth
> posting?
>
> "Marvin Oliver" <m3599137@earthlink.net> wrote in message
> news:EMY3e.4610$x4.717@newsread1.news.pas.earthlin k.net...
>
> > Yesterday found out the hard way I don't have 4wd. Today checked front
> > axle vacuum motor and found it engages. With all four wheels off the
> > ground I engaged 4L and put transmission in gear. While the rear wheels
> > spun the front wheels do not spin. I notice the front drive shaft was
> > slowly rotating, but I cound easily stop it with by hand. Same results for
> > 4H. I adjusted the linkage just to be sure.
> >
> > I have the np231 J xfer case. Is the xfer case bad? Is there a possible
> > simple fix or do I replace it with a rebuilt? Is there a suggested
> > upgrade? I just mess around on the back roads in Big Bear area.
> >
04-05-2005, 09:30 AM
#7
Guest
Posts: n/a
Re: 94 yj xfer case not engaging front axle
No one really had the heart to tell you what you already have figured
likely....
That t-case was a chain drive one so at the 'best' you are looking at a
new chain and sprockets.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Marvin Oliver wrote:
>
> Is this not making it to the news group or is there no comment worth
> posting?
>
> "Marvin Oliver" <m3599137@earthlink.net> wrote in message
> news:EMY3e.4610$x4.717@newsread1.news.pas.earthlin k.net...
>
> > Yesterday found out the hard way I don't have 4wd. Today checked front
> > axle vacuum motor and found it engages. With all four wheels off the
> > ground I engaged 4L and put transmission in gear. While the rear wheels
> > spun the front wheels do not spin. I notice the front drive shaft was
> > slowly rotating, but I cound easily stop it with by hand. Same results for
> > 4H. I adjusted the linkage just to be sure.
> >
> > I have the np231 J xfer case. Is the xfer case bad? Is there a possible
> > simple fix or do I replace it with a rebuilt? Is there a suggested
> > upgrade? I just mess around on the back roads in Big Bear area.
> >
likely....
That t-case was a chain drive one so at the 'best' you are looking at a
new chain and sprockets.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Marvin Oliver wrote:
>
> Is this not making it to the news group or is there no comment worth
> posting?
>
> "Marvin Oliver" <m3599137@earthlink.net> wrote in message
> news:EMY3e.4610$x4.717@newsread1.news.pas.earthlin k.net...
>
> > Yesterday found out the hard way I don't have 4wd. Today checked front
> > axle vacuum motor and found it engages. With all four wheels off the
> > ground I engaged 4L and put transmission in gear. While the rear wheels
> > spun the front wheels do not spin. I notice the front drive shaft was
> > slowly rotating, but I cound easily stop it with by hand. Same results for
> > 4H. I adjusted the linkage just to be sure.
> >
> > I have the np231 J xfer case. Is the xfer case bad? Is there a possible
> > simple fix or do I replace it with a rebuilt? Is there a suggested
> > upgrade? I just mess around on the back roads in Big Bear area.
> >
04-05-2005, 09:30 AM
#8
Guest
Posts: n/a
Re: 94 yj xfer case not engaging front axle
No one really had the heart to tell you what you already have figured
likely....
That t-case was a chain drive one so at the 'best' you are looking at a
new chain and sprockets.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Marvin Oliver wrote:
>
> Is this not making it to the news group or is there no comment worth
> posting?
>
> "Marvin Oliver" <m3599137@earthlink.net> wrote in message
> news:EMY3e.4610$x4.717@newsread1.news.pas.earthlin k.net...
>
> > Yesterday found out the hard way I don't have 4wd. Today checked front
> > axle vacuum motor and found it engages. With all four wheels off the
> > ground I engaged 4L and put transmission in gear. While the rear wheels
> > spun the front wheels do not spin. I notice the front drive shaft was
> > slowly rotating, but I cound easily stop it with by hand. Same results for
> > 4H. I adjusted the linkage just to be sure.
> >
> > I have the np231 J xfer case. Is the xfer case bad? Is there a possible
> > simple fix or do I replace it with a rebuilt? Is there a suggested
> > upgrade? I just mess around on the back roads in Big Bear area.
> >
likely....
That t-case was a chain drive one so at the 'best' you are looking at a
new chain and sprockets.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Marvin Oliver wrote:
>
> Is this not making it to the news group or is there no comment worth
> posting?
>
> "Marvin Oliver" <m3599137@earthlink.net> wrote in message
> news:EMY3e.4610$x4.717@newsread1.news.pas.earthlin k.net...
>
> > Yesterday found out the hard way I don't have 4wd. Today checked front
> > axle vacuum motor and found it engages. With all four wheels off the
> > ground I engaged 4L and put transmission in gear. While the rear wheels
> > spun the front wheels do not spin. I notice the front drive shaft was
> > slowly rotating, but I cound easily stop it with by hand. Same results for
> > 4H. I adjusted the linkage just to be sure.
> >
> > I have the np231 J xfer case. Is the xfer case bad? Is there a possible
> > simple fix or do I replace it with a rebuilt? Is there a suggested
> > upgrade? I just mess around on the back roads in Big Bear area.
> >
04-05-2005, 09:30 AM
#9
Guest
Posts: n/a
Re: 94 yj xfer case not engaging front axle
No one really had the heart to tell you what you already have figured
likely....
That t-case was a chain drive one so at the 'best' you are looking at a
new chain and sprockets.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Marvin Oliver wrote:
>
> Is this not making it to the news group or is there no comment worth
> posting?
>
> "Marvin Oliver" <m3599137@earthlink.net> wrote in message
> news:EMY3e.4610$x4.717@newsread1.news.pas.earthlin k.net...
>
> > Yesterday found out the hard way I don't have 4wd. Today checked front
> > axle vacuum motor and found it engages. With all four wheels off the
> > ground I engaged 4L and put transmission in gear. While the rear wheels
> > spun the front wheels do not spin. I notice the front drive shaft was
> > slowly rotating, but I cound easily stop it with by hand. Same results for
> > 4H. I adjusted the linkage just to be sure.
> >
> > I have the np231 J xfer case. Is the xfer case bad? Is there a possible
> > simple fix or do I replace it with a rebuilt? Is there a suggested
> > upgrade? I just mess around on the back roads in Big Bear area.
> >
likely....
That t-case was a chain drive one so at the 'best' you are looking at a
new chain and sprockets.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Marvin Oliver wrote:
>
> Is this not making it to the news group or is there no comment worth
> posting?
>
> "Marvin Oliver" <m3599137@earthlink.net> wrote in message
> news:EMY3e.4610$x4.717@newsread1.news.pas.earthlin k.net...
>
> > Yesterday found out the hard way I don't have 4wd. Today checked front
> > axle vacuum motor and found it engages. With all four wheels off the
> > ground I engaged 4L and put transmission in gear. While the rear wheels
> > spun the front wheels do not spin. I notice the front drive shaft was
> > slowly rotating, but I cound easily stop it with by hand. Same results for
> > 4H. I adjusted the linkage just to be sure.
> >
> > I have the np231 J xfer case. Is the xfer case bad? Is there a possible
> > simple fix or do I replace it with a rebuilt? Is there a suggested
> > upgrade? I just mess around on the back roads in Big Bear area.
> >
04-06-2005, 03:00 PM
#10
Guest
Posts: n/a
Re: 94 yj xfer case not engaging front axle
On Tue, 05 Apr 2005 13:04:01 GMT, Marvin Oliver wrote:
> Is this not making it to the news group or is there no comment worth
> posting?
My comment on this isn't worth posting: "I don't know".
Sorry I can't be more helpful.
-D
--
One OS to rule them all, one OS to find them,
One OS to bring them all and in the darkness bind them,
In the Land of Redmond, where the Shadows lie.
www: http://dman13.dyndns.org/~dman/ jabber: dman@dman13.dyndns.org
> Is this not making it to the news group or is there no comment worth
> posting?
My comment on this isn't worth posting: "I don't know".
Sorry I can't be more helpful.
-D
--
One OS to rule them all, one OS to find them,
One OS to bring them all and in the darkness bind them,
In the Land of Redmond, where the Shadows lie.
www: http://dman13.dyndns.org/~dman/ jabber: dman@dman13.dyndns.org