94 Wrangler very hard shifts...
08-24-2004, 04:57 PM
#11
Guest
Posts: n/a
Re: 94 Wrangler very hard shifts...
You should check the level for sure!
And to type, well if the level is fine then a change to the proper fluid
can't hurt anything and you will know for sure that isn't an issue.
Where does the clutch pedal engage? If it is all the way to either end
of it's travel, then a bleed or replace could be in order, but if it
tags in the middle of the throw, not likely any trouble with it.
Mike
none wrote:
>
> I just bought it a few weeks ago, and I'm just starting to diagnose the
> problem. It's my understanding that the previous owner just replaced
> the tranny. Since it was just replaced, I'm assuming the fluid is
> topped off, but I don't know that for sure. Also if he put GL-5 in it,
> could that cause hard shifts? I'm just full of questions aren'tI. I'm
> not a mechanic by no means, but feel confident that I can resolve this
> issue.
>
> Thanks again
>
> Mike Romain wrote:
>
> > When was the last time you checked the fluid?
> >
> > Just so you know, Jeep didn't think you needed a high water vent on the
> > tranny, so if you have done any water crossings, water in the tranny oil
> > is also possible.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > none wrote:
> >
> >>I have 80,000 on my AX-5 tranny and shifting into first gear is very
> >>difficult. If I rev the engine a little the gear will eventually
> >>engage. Would this be a sign that the clutch is not fully disengaging?
> >> I have no grinding so I'm thinking the syncros are fine. Should I
> >>start with a fluid bleed?
> >>
> >>Thanks for your help
> >>Zak
And to type, well if the level is fine then a change to the proper fluid
can't hurt anything and you will know for sure that isn't an issue.
Where does the clutch pedal engage? If it is all the way to either end
of it's travel, then a bleed or replace could be in order, but if it
tags in the middle of the throw, not likely any trouble with it.
Mike
none wrote:
>
> I just bought it a few weeks ago, and I'm just starting to diagnose the
> problem. It's my understanding that the previous owner just replaced
> the tranny. Since it was just replaced, I'm assuming the fluid is
> topped off, but I don't know that for sure. Also if he put GL-5 in it,
> could that cause hard shifts? I'm just full of questions aren'tI. I'm
> not a mechanic by no means, but feel confident that I can resolve this
> issue.
>
> Thanks again
>
> Mike Romain wrote:
>
> > When was the last time you checked the fluid?
> >
> > Just so you know, Jeep didn't think you needed a high water vent on the
> > tranny, so if you have done any water crossings, water in the tranny oil
> > is also possible.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > none wrote:
> >
> >>I have 80,000 on my AX-5 tranny and shifting into first gear is very
> >>difficult. If I rev the engine a little the gear will eventually
> >>engage. Would this be a sign that the clutch is not fully disengaging?
> >> I have no grinding so I'm thinking the syncros are fine. Should I
> >>start with a fluid bleed?
> >>
> >>Thanks for your help
> >>Zak
08-24-2004, 04:57 PM
#12
Guest
Posts: n/a
Re: 94 Wrangler very hard shifts...
You should check the level for sure!
And to type, well if the level is fine then a change to the proper fluid
can't hurt anything and you will know for sure that isn't an issue.
Where does the clutch pedal engage? If it is all the way to either end
of it's travel, then a bleed or replace could be in order, but if it
tags in the middle of the throw, not likely any trouble with it.
Mike
none wrote:
>
> I just bought it a few weeks ago, and I'm just starting to diagnose the
> problem. It's my understanding that the previous owner just replaced
> the tranny. Since it was just replaced, I'm assuming the fluid is
> topped off, but I don't know that for sure. Also if he put GL-5 in it,
> could that cause hard shifts? I'm just full of questions aren'tI. I'm
> not a mechanic by no means, but feel confident that I can resolve this
> issue.
>
> Thanks again
>
> Mike Romain wrote:
>
> > When was the last time you checked the fluid?
> >
> > Just so you know, Jeep didn't think you needed a high water vent on the
> > tranny, so if you have done any water crossings, water in the tranny oil
> > is also possible.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > none wrote:
> >
> >>I have 80,000 on my AX-5 tranny and shifting into first gear is very
> >>difficult. If I rev the engine a little the gear will eventually
> >>engage. Would this be a sign that the clutch is not fully disengaging?
> >> I have no grinding so I'm thinking the syncros are fine. Should I
> >>start with a fluid bleed?
> >>
> >>Thanks for your help
> >>Zak
And to type, well if the level is fine then a change to the proper fluid
can't hurt anything and you will know for sure that isn't an issue.
Where does the clutch pedal engage? If it is all the way to either end
of it's travel, then a bleed or replace could be in order, but if it
tags in the middle of the throw, not likely any trouble with it.
Mike
none wrote:
>
> I just bought it a few weeks ago, and I'm just starting to diagnose the
> problem. It's my understanding that the previous owner just replaced
> the tranny. Since it was just replaced, I'm assuming the fluid is
> topped off, but I don't know that for sure. Also if he put GL-5 in it,
> could that cause hard shifts? I'm just full of questions aren'tI. I'm
> not a mechanic by no means, but feel confident that I can resolve this
> issue.
>
> Thanks again
>
> Mike Romain wrote:
>
> > When was the last time you checked the fluid?
> >
> > Just so you know, Jeep didn't think you needed a high water vent on the
> > tranny, so if you have done any water crossings, water in the tranny oil
> > is also possible.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > none wrote:
> >
> >>I have 80,000 on my AX-5 tranny and shifting into first gear is very
> >>difficult. If I rev the engine a little the gear will eventually
> >>engage. Would this be a sign that the clutch is not fully disengaging?
> >> I have no grinding so I'm thinking the syncros are fine. Should I
> >>start with a fluid bleed?
> >>
> >>Thanks for your help
> >>Zak
08-24-2004, 04:57 PM
#13
Guest
Posts: n/a
Re: 94 Wrangler very hard shifts...
You should check the level for sure!
And to type, well if the level is fine then a change to the proper fluid
can't hurt anything and you will know for sure that isn't an issue.
Where does the clutch pedal engage? If it is all the way to either end
of it's travel, then a bleed or replace could be in order, but if it
tags in the middle of the throw, not likely any trouble with it.
Mike
none wrote:
>
> I just bought it a few weeks ago, and I'm just starting to diagnose the
> problem. It's my understanding that the previous owner just replaced
> the tranny. Since it was just replaced, I'm assuming the fluid is
> topped off, but I don't know that for sure. Also if he put GL-5 in it,
> could that cause hard shifts? I'm just full of questions aren'tI. I'm
> not a mechanic by no means, but feel confident that I can resolve this
> issue.
>
> Thanks again
>
> Mike Romain wrote:
>
> > When was the last time you checked the fluid?
> >
> > Just so you know, Jeep didn't think you needed a high water vent on the
> > tranny, so if you have done any water crossings, water in the tranny oil
> > is also possible.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > none wrote:
> >
> >>I have 80,000 on my AX-5 tranny and shifting into first gear is very
> >>difficult. If I rev the engine a little the gear will eventually
> >>engage. Would this be a sign that the clutch is not fully disengaging?
> >> I have no grinding so I'm thinking the syncros are fine. Should I
> >>start with a fluid bleed?
> >>
> >>Thanks for your help
> >>Zak
And to type, well if the level is fine then a change to the proper fluid
can't hurt anything and you will know for sure that isn't an issue.
Where does the clutch pedal engage? If it is all the way to either end
of it's travel, then a bleed or replace could be in order, but if it
tags in the middle of the throw, not likely any trouble with it.
Mike
none wrote:
>
> I just bought it a few weeks ago, and I'm just starting to diagnose the
> problem. It's my understanding that the previous owner just replaced
> the tranny. Since it was just replaced, I'm assuming the fluid is
> topped off, but I don't know that for sure. Also if he put GL-5 in it,
> could that cause hard shifts? I'm just full of questions aren'tI. I'm
> not a mechanic by no means, but feel confident that I can resolve this
> issue.
>
> Thanks again
>
> Mike Romain wrote:
>
> > When was the last time you checked the fluid?
> >
> > Just so you know, Jeep didn't think you needed a high water vent on the
> > tranny, so if you have done any water crossings, water in the tranny oil
> > is also possible.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > none wrote:
> >
> >>I have 80,000 on my AX-5 tranny and shifting into first gear is very
> >>difficult. If I rev the engine a little the gear will eventually
> >>engage. Would this be a sign that the clutch is not fully disengaging?
> >> I have no grinding so I'm thinking the syncros are fine. Should I
> >>start with a fluid bleed?
> >>
> >>Thanks for your help
> >>Zak
08-24-2004, 05:31 PM
#14
Guest
Posts: n/a
Re: 94 Wrangler very hard shifts...
While GL-5 is not the best possible lube in that it is harmful to the
long-term health of the synchronizers, it's not normally a cause of this
kind of problem.
Jerry
--
Jerry Bransford
PP-ASEL N6TAY
See the Geezer Jeep at
http://members.***.net/jerrypb/
"none" <zakwhitak@*n0_spam*hotmail.com> wrote in message
news:cgfovk$sf1$1@uni00nw.unity.ncsu.edu...
> I just bought it a few weeks ago, and I'm just starting to diagnose the
> problem. It's my understanding that the previous owner just replaced
> the tranny. Since it was just replaced, I'm assuming the fluid is
> topped off, but I don't know that for sure. Also if he put GL-5 in it,
> could that cause hard shifts? I'm just full of questions aren'tI. I'm
> not a mechanic by no means, but feel confident that I can resolve this
> issue.
>
> Thanks again
>
> Mike Romain wrote:
>
> > When was the last time you checked the fluid?
> >
> > Just so you know, Jeep didn't think you needed a high water vent on the
> > tranny, so if you have done any water crossings, water in the tranny oil
> > is also possible.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > none wrote:
> >
> >>I have 80,000 on my AX-5 tranny and shifting into first gear is very
> >>difficult. If I rev the engine a little the gear will eventually
> >>engage. Would this be a sign that the clutch is not fully disengaging?
> >> I have no grinding so I'm thinking the syncros are fine. Should I
> >>start with a fluid bleed?
> >>
> >>Thanks for your help
> >>Zak
long-term health of the synchronizers, it's not normally a cause of this
kind of problem.
Jerry
--
Jerry Bransford
PP-ASEL N6TAY
See the Geezer Jeep at
http://members.***.net/jerrypb/
"none" <zakwhitak@*n0_spam*hotmail.com> wrote in message
news:cgfovk$sf1$1@uni00nw.unity.ncsu.edu...
> I just bought it a few weeks ago, and I'm just starting to diagnose the
> problem. It's my understanding that the previous owner just replaced
> the tranny. Since it was just replaced, I'm assuming the fluid is
> topped off, but I don't know that for sure. Also if he put GL-5 in it,
> could that cause hard shifts? I'm just full of questions aren'tI. I'm
> not a mechanic by no means, but feel confident that I can resolve this
> issue.
>
> Thanks again
>
> Mike Romain wrote:
>
> > When was the last time you checked the fluid?
> >
> > Just so you know, Jeep didn't think you needed a high water vent on the
> > tranny, so if you have done any water crossings, water in the tranny oil
> > is also possible.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > none wrote:
> >
> >>I have 80,000 on my AX-5 tranny and shifting into first gear is very
> >>difficult. If I rev the engine a little the gear will eventually
> >>engage. Would this be a sign that the clutch is not fully disengaging?
> >> I have no grinding so I'm thinking the syncros are fine. Should I
> >>start with a fluid bleed?
> >>
> >>Thanks for your help
> >>Zak
08-24-2004, 05:31 PM
#15
Guest
Posts: n/a
Re: 94 Wrangler very hard shifts...
While GL-5 is not the best possible lube in that it is harmful to the
long-term health of the synchronizers, it's not normally a cause of this
kind of problem.
Jerry
--
Jerry Bransford
PP-ASEL N6TAY
See the Geezer Jeep at
http://members.***.net/jerrypb/
"none" <zakwhitak@*n0_spam*hotmail.com> wrote in message
news:cgfovk$sf1$1@uni00nw.unity.ncsu.edu...
> I just bought it a few weeks ago, and I'm just starting to diagnose the
> problem. It's my understanding that the previous owner just replaced
> the tranny. Since it was just replaced, I'm assuming the fluid is
> topped off, but I don't know that for sure. Also if he put GL-5 in it,
> could that cause hard shifts? I'm just full of questions aren'tI. I'm
> not a mechanic by no means, but feel confident that I can resolve this
> issue.
>
> Thanks again
>
> Mike Romain wrote:
>
> > When was the last time you checked the fluid?
> >
> > Just so you know, Jeep didn't think you needed a high water vent on the
> > tranny, so if you have done any water crossings, water in the tranny oil
> > is also possible.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > none wrote:
> >
> >>I have 80,000 on my AX-5 tranny and shifting into first gear is very
> >>difficult. If I rev the engine a little the gear will eventually
> >>engage. Would this be a sign that the clutch is not fully disengaging?
> >> I have no grinding so I'm thinking the syncros are fine. Should I
> >>start with a fluid bleed?
> >>
> >>Thanks for your help
> >>Zak
long-term health of the synchronizers, it's not normally a cause of this
kind of problem.
Jerry
--
Jerry Bransford
PP-ASEL N6TAY
See the Geezer Jeep at
http://members.***.net/jerrypb/
"none" <zakwhitak@*n0_spam*hotmail.com> wrote in message
news:cgfovk$sf1$1@uni00nw.unity.ncsu.edu...
> I just bought it a few weeks ago, and I'm just starting to diagnose the
> problem. It's my understanding that the previous owner just replaced
> the tranny. Since it was just replaced, I'm assuming the fluid is
> topped off, but I don't know that for sure. Also if he put GL-5 in it,
> could that cause hard shifts? I'm just full of questions aren'tI. I'm
> not a mechanic by no means, but feel confident that I can resolve this
> issue.
>
> Thanks again
>
> Mike Romain wrote:
>
> > When was the last time you checked the fluid?
> >
> > Just so you know, Jeep didn't think you needed a high water vent on the
> > tranny, so if you have done any water crossings, water in the tranny oil
> > is also possible.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > none wrote:
> >
> >>I have 80,000 on my AX-5 tranny and shifting into first gear is very
> >>difficult. If I rev the engine a little the gear will eventually
> >>engage. Would this be a sign that the clutch is not fully disengaging?
> >> I have no grinding so I'm thinking the syncros are fine. Should I
> >>start with a fluid bleed?
> >>
> >>Thanks for your help
> >>Zak
08-24-2004, 05:31 PM
#16
Guest
Posts: n/a
Re: 94 Wrangler very hard shifts...
While GL-5 is not the best possible lube in that it is harmful to the
long-term health of the synchronizers, it's not normally a cause of this
kind of problem.
Jerry
--
Jerry Bransford
PP-ASEL N6TAY
See the Geezer Jeep at
http://members.***.net/jerrypb/
"none" <zakwhitak@*n0_spam*hotmail.com> wrote in message
news:cgfovk$sf1$1@uni00nw.unity.ncsu.edu...
> I just bought it a few weeks ago, and I'm just starting to diagnose the
> problem. It's my understanding that the previous owner just replaced
> the tranny. Since it was just replaced, I'm assuming the fluid is
> topped off, but I don't know that for sure. Also if he put GL-5 in it,
> could that cause hard shifts? I'm just full of questions aren'tI. I'm
> not a mechanic by no means, but feel confident that I can resolve this
> issue.
>
> Thanks again
>
> Mike Romain wrote:
>
> > When was the last time you checked the fluid?
> >
> > Just so you know, Jeep didn't think you needed a high water vent on the
> > tranny, so if you have done any water crossings, water in the tranny oil
> > is also possible.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > none wrote:
> >
> >>I have 80,000 on my AX-5 tranny and shifting into first gear is very
> >>difficult. If I rev the engine a little the gear will eventually
> >>engage. Would this be a sign that the clutch is not fully disengaging?
> >> I have no grinding so I'm thinking the syncros are fine. Should I
> >>start with a fluid bleed?
> >>
> >>Thanks for your help
> >>Zak
long-term health of the synchronizers, it's not normally a cause of this
kind of problem.
Jerry
--
Jerry Bransford
PP-ASEL N6TAY
See the Geezer Jeep at
http://members.***.net/jerrypb/
"none" <zakwhitak@*n0_spam*hotmail.com> wrote in message
news:cgfovk$sf1$1@uni00nw.unity.ncsu.edu...
> I just bought it a few weeks ago, and I'm just starting to diagnose the
> problem. It's my understanding that the previous owner just replaced
> the tranny. Since it was just replaced, I'm assuming the fluid is
> topped off, but I don't know that for sure. Also if he put GL-5 in it,
> could that cause hard shifts? I'm just full of questions aren'tI. I'm
> not a mechanic by no means, but feel confident that I can resolve this
> issue.
>
> Thanks again
>
> Mike Romain wrote:
>
> > When was the last time you checked the fluid?
> >
> > Just so you know, Jeep didn't think you needed a high water vent on the
> > tranny, so if you have done any water crossings, water in the tranny oil
> > is also possible.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > none wrote:
> >
> >>I have 80,000 on my AX-5 tranny and shifting into first gear is very
> >>difficult. If I rev the engine a little the gear will eventually
> >>engage. Would this be a sign that the clutch is not fully disengaging?
> >> I have no grinding so I'm thinking the syncros are fine. Should I
> >>start with a fluid bleed?
> >>
> >>Thanks for your help
> >>Zak
08-24-2004, 05:31 PM
#17
Guest
Posts: n/a
Re: 94 Wrangler very hard shifts...
While GL-5 is not the best possible lube in that it is harmful to the
long-term health of the synchronizers, it's not normally a cause of this
kind of problem.
Jerry
--
Jerry Bransford
PP-ASEL N6TAY
See the Geezer Jeep at
http://members.***.net/jerrypb/
"none" <zakwhitak@*n0_spam*hotmail.com> wrote in message
news:cgfovk$sf1$1@uni00nw.unity.ncsu.edu...
> I just bought it a few weeks ago, and I'm just starting to diagnose the
> problem. It's my understanding that the previous owner just replaced
> the tranny. Since it was just replaced, I'm assuming the fluid is
> topped off, but I don't know that for sure. Also if he put GL-5 in it,
> could that cause hard shifts? I'm just full of questions aren'tI. I'm
> not a mechanic by no means, but feel confident that I can resolve this
> issue.
>
> Thanks again
>
> Mike Romain wrote:
>
> > When was the last time you checked the fluid?
> >
> > Just so you know, Jeep didn't think you needed a high water vent on the
> > tranny, so if you have done any water crossings, water in the tranny oil
> > is also possible.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > none wrote:
> >
> >>I have 80,000 on my AX-5 tranny and shifting into first gear is very
> >>difficult. If I rev the engine a little the gear will eventually
> >>engage. Would this be a sign that the clutch is not fully disengaging?
> >> I have no grinding so I'm thinking the syncros are fine. Should I
> >>start with a fluid bleed?
> >>
> >>Thanks for your help
> >>Zak
long-term health of the synchronizers, it's not normally a cause of this
kind of problem.
Jerry
--
Jerry Bransford
PP-ASEL N6TAY
See the Geezer Jeep at
http://members.***.net/jerrypb/
"none" <zakwhitak@*n0_spam*hotmail.com> wrote in message
news:cgfovk$sf1$1@uni00nw.unity.ncsu.edu...
> I just bought it a few weeks ago, and I'm just starting to diagnose the
> problem. It's my understanding that the previous owner just replaced
> the tranny. Since it was just replaced, I'm assuming the fluid is
> topped off, but I don't know that for sure. Also if he put GL-5 in it,
> could that cause hard shifts? I'm just full of questions aren'tI. I'm
> not a mechanic by no means, but feel confident that I can resolve this
> issue.
>
> Thanks again
>
> Mike Romain wrote:
>
> > When was the last time you checked the fluid?
> >
> > Just so you know, Jeep didn't think you needed a high water vent on the
> > tranny, so if you have done any water crossings, water in the tranny oil
> > is also possible.
> >
> > Mike
> > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> > 88 Cherokee 235 BFG AT's
> >
> > none wrote:
> >
> >>I have 80,000 on my AX-5 tranny and shifting into first gear is very
> >>difficult. If I rev the engine a little the gear will eventually
> >>engage. Would this be a sign that the clutch is not fully disengaging?
> >> I have no grinding so I'm thinking the syncros are fine. Should I
> >>start with a fluid bleed?
> >>
> >>Thanks for your help
> >>Zak
08-25-2004, 12:02 AM
#18
Guest
Posts: n/a
Re: 94 Wrangler very hard shifts...
This sounds more like clutch disengagement, rather than a trans fluid issue.
However, if the issue goes away when the trans is fully warmed up, could be
the gear oil type or weight.
"none" <zakwhitak@*n0_spam*hotmail.com> wrote in message
news:cgfh7s$o1c$2@uni00nw.unity.ncsu.edu...
> I have 80,000 on my AX-5 tranny and shifting into first gear is very
> difficult. If I rev the engine a little the gear will eventually
> engage. Would this be a sign that the clutch is not fully disengaging?
> I have no grinding so I'm thinking the syncros are fine. Should I
> start with a fluid bleed?
>
> Thanks for your help
> Zak
However, if the issue goes away when the trans is fully warmed up, could be
the gear oil type or weight.
"none" <zakwhitak@*n0_spam*hotmail.com> wrote in message
news:cgfh7s$o1c$2@uni00nw.unity.ncsu.edu...
> I have 80,000 on my AX-5 tranny and shifting into first gear is very
> difficult. If I rev the engine a little the gear will eventually
> engage. Would this be a sign that the clutch is not fully disengaging?
> I have no grinding so I'm thinking the syncros are fine. Should I
> start with a fluid bleed?
>
> Thanks for your help
> Zak
08-25-2004, 12:02 AM
#19
Guest
Posts: n/a
Re: 94 Wrangler very hard shifts...
This sounds more like clutch disengagement, rather than a trans fluid issue.
However, if the issue goes away when the trans is fully warmed up, could be
the gear oil type or weight.
"none" <zakwhitak@*n0_spam*hotmail.com> wrote in message
news:cgfh7s$o1c$2@uni00nw.unity.ncsu.edu...
> I have 80,000 on my AX-5 tranny and shifting into first gear is very
> difficult. If I rev the engine a little the gear will eventually
> engage. Would this be a sign that the clutch is not fully disengaging?
> I have no grinding so I'm thinking the syncros are fine. Should I
> start with a fluid bleed?
>
> Thanks for your help
> Zak
However, if the issue goes away when the trans is fully warmed up, could be
the gear oil type or weight.
"none" <zakwhitak@*n0_spam*hotmail.com> wrote in message
news:cgfh7s$o1c$2@uni00nw.unity.ncsu.edu...
> I have 80,000 on my AX-5 tranny and shifting into first gear is very
> difficult. If I rev the engine a little the gear will eventually
> engage. Would this be a sign that the clutch is not fully disengaging?
> I have no grinding so I'm thinking the syncros are fine. Should I
> start with a fluid bleed?
>
> Thanks for your help
> Zak
08-25-2004, 12:02 AM
#20
Guest
Posts: n/a
Re: 94 Wrangler very hard shifts...
This sounds more like clutch disengagement, rather than a trans fluid issue.
However, if the issue goes away when the trans is fully warmed up, could be
the gear oil type or weight.
"none" <zakwhitak@*n0_spam*hotmail.com> wrote in message
news:cgfh7s$o1c$2@uni00nw.unity.ncsu.edu...
> I have 80,000 on my AX-5 tranny and shifting into first gear is very
> difficult. If I rev the engine a little the gear will eventually
> engage. Would this be a sign that the clutch is not fully disengaging?
> I have no grinding so I'm thinking the syncros are fine. Should I
> start with a fluid bleed?
>
> Thanks for your help
> Zak
However, if the issue goes away when the trans is fully warmed up, could be
the gear oil type or weight.
"none" <zakwhitak@*n0_spam*hotmail.com> wrote in message
news:cgfh7s$o1c$2@uni00nw.unity.ncsu.edu...
> I have 80,000 on my AX-5 tranny and shifting into first gear is very
> difficult. If I rev the engine a little the gear will eventually
> engage. Would this be a sign that the clutch is not fully disengaging?
> I have no grinding so I'm thinking the syncros are fine. Should I
> start with a fluid bleed?
>
> Thanks for your help
> Zak
