93ZJ - 4 wheel drive switch + bad coolant sersor
04-13-2007, 08:39 PM
#1
Guest
Posts: n/a
93ZJ - 4 wheel drive switch + bad coolant sersor
Hi Folk,
In my 93 V8 ZJ, the following error messages flash in and out the VIC once a
while.
1, Service 4 wheel drive switch, and
2, bad coolant sersor
I don't notice if I have a 4 wheel drive switch?! I only have 4hi and 4lo.
Since they flash in and out, does it indicate a bad connection @ somewhere?
Any input is welcome.
Thanks in advance
Paul
In my 93 V8 ZJ, the following error messages flash in and out the VIC once a
while.
1, Service 4 wheel drive switch, and
2, bad coolant sersor
I don't notice if I have a 4 wheel drive switch?! I only have 4hi and 4lo.
Since they flash in and out, does it indicate a bad connection @ somewhere?
Any input is welcome.
Thanks in advance
Paul
04-14-2007, 02:46 AM
#2
Guest
Posts: n/a
Re: 93ZJ - 4 wheel drive switch + bad coolant sersor
Bogey Buster wrote:
> Hi Folk,
>
> In my 93 V8 ZJ, the following error messages flash in and out the VIC
> once a while.
>
> 1, Service 4 wheel drive switch, and
> 2, bad coolant sersor
>
> I don't notice if I have a 4 wheel drive switch?! I only have 4hi and
> 4lo. Since they flash in and out, does it indicate a bad connection @
> somewhere?
You have the Quadratrack transfer case. Problem is the sensor is
internal to the xfr case. I'd remove/clean/reinstall the connector
first. It's an oval 4pin located on the transfer case. not too easy
to get at though.
On the bright side, the 4wd and coolant sensor errors are not
critical providing the range selection is correct, the fluid
has been changed regularly, and you keep an eye on the overflow
bottle so the level is between fill and add with the engine at
operating temp.
As for 2, clean the contacts on the sensor that is on the
coolant reservoir, it's likely a bit corroded.
--
-- DougW -- 93 ZJ 4.0 http://revbeergoggles.com
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
> Hi Folk,
>
> In my 93 V8 ZJ, the following error messages flash in and out the VIC
> once a while.
>
> 1, Service 4 wheel drive switch, and
> 2, bad coolant sersor
>
> I don't notice if I have a 4 wheel drive switch?! I only have 4hi and
> 4lo. Since they flash in and out, does it indicate a bad connection @
> somewhere?
You have the Quadratrack transfer case. Problem is the sensor is
internal to the xfr case. I'd remove/clean/reinstall the connector
first. It's an oval 4pin located on the transfer case. not too easy
to get at though.
On the bright side, the 4wd and coolant sensor errors are not
critical providing the range selection is correct, the fluid
has been changed regularly, and you keep an eye on the overflow
bottle so the level is between fill and add with the engine at
operating temp.
As for 2, clean the contacts on the sensor that is on the
coolant reservoir, it's likely a bit corroded.
--
-- DougW -- 93 ZJ 4.0 http://revbeergoggles.com
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
04-14-2007, 02:46 AM
#3
Guest
Posts: n/a
Re: 93ZJ - 4 wheel drive switch + bad coolant sersor
Bogey Buster wrote:
> Hi Folk,
>
> In my 93 V8 ZJ, the following error messages flash in and out the VIC
> once a while.
>
> 1, Service 4 wheel drive switch, and
> 2, bad coolant sersor
>
> I don't notice if I have a 4 wheel drive switch?! I only have 4hi and
> 4lo. Since they flash in and out, does it indicate a bad connection @
> somewhere?
You have the Quadratrack transfer case. Problem is the sensor is
internal to the xfr case. I'd remove/clean/reinstall the connector
first. It's an oval 4pin located on the transfer case. not too easy
to get at though.
On the bright side, the 4wd and coolant sensor errors are not
critical providing the range selection is correct, the fluid
has been changed regularly, and you keep an eye on the overflow
bottle so the level is between fill and add with the engine at
operating temp.
As for 2, clean the contacts on the sensor that is on the
coolant reservoir, it's likely a bit corroded.
--
-- DougW -- 93 ZJ 4.0 http://revbeergoggles.com
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
> Hi Folk,
>
> In my 93 V8 ZJ, the following error messages flash in and out the VIC
> once a while.
>
> 1, Service 4 wheel drive switch, and
> 2, bad coolant sersor
>
> I don't notice if I have a 4 wheel drive switch?! I only have 4hi and
> 4lo. Since they flash in and out, does it indicate a bad connection @
> somewhere?
You have the Quadratrack transfer case. Problem is the sensor is
internal to the xfr case. I'd remove/clean/reinstall the connector
first. It's an oval 4pin located on the transfer case. not too easy
to get at though.
On the bright side, the 4wd and coolant sensor errors are not
critical providing the range selection is correct, the fluid
has been changed regularly, and you keep an eye on the overflow
bottle so the level is between fill and add with the engine at
operating temp.
As for 2, clean the contacts on the sensor that is on the
coolant reservoir, it's likely a bit corroded.
--
-- DougW -- 93 ZJ 4.0 http://revbeergoggles.com
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
04-14-2007, 02:46 AM
#4
Guest
Posts: n/a
Re: 93ZJ - 4 wheel drive switch + bad coolant sersor
Bogey Buster wrote:
> Hi Folk,
>
> In my 93 V8 ZJ, the following error messages flash in and out the VIC
> once a while.
>
> 1, Service 4 wheel drive switch, and
> 2, bad coolant sersor
>
> I don't notice if I have a 4 wheel drive switch?! I only have 4hi and
> 4lo. Since they flash in and out, does it indicate a bad connection @
> somewhere?
You have the Quadratrack transfer case. Problem is the sensor is
internal to the xfr case. I'd remove/clean/reinstall the connector
first. It's an oval 4pin located on the transfer case. not too easy
to get at though.
On the bright side, the 4wd and coolant sensor errors are not
critical providing the range selection is correct, the fluid
has been changed regularly, and you keep an eye on the overflow
bottle so the level is between fill and add with the engine at
operating temp.
As for 2, clean the contacts on the sensor that is on the
coolant reservoir, it's likely a bit corroded.
--
-- DougW -- 93 ZJ 4.0 http://revbeergoggles.com
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
> Hi Folk,
>
> In my 93 V8 ZJ, the following error messages flash in and out the VIC
> once a while.
>
> 1, Service 4 wheel drive switch, and
> 2, bad coolant sersor
>
> I don't notice if I have a 4 wheel drive switch?! I only have 4hi and
> 4lo. Since they flash in and out, does it indicate a bad connection @
> somewhere?
You have the Quadratrack transfer case. Problem is the sensor is
internal to the xfr case. I'd remove/clean/reinstall the connector
first. It's an oval 4pin located on the transfer case. not too easy
to get at though.
On the bright side, the 4wd and coolant sensor errors are not
critical providing the range selection is correct, the fluid
has been changed regularly, and you keep an eye on the overflow
bottle so the level is between fill and add with the engine at
operating temp.
As for 2, clean the contacts on the sensor that is on the
coolant reservoir, it's likely a bit corroded.
--
-- DougW -- 93 ZJ 4.0 http://revbeergoggles.com
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!
04-14-2007, 01:19 PM
#5
Guest
Posts: n/a
Re: 93ZJ - 4 wheel drive switch + bad coolant sersor
"DougW" <post.replies@invalid.address> wrote in message
news:QM_Th.113259$nh4.84489@newsfe20.lga...
> Bogey Buster wrote:
>> Hi Folk,
>>
>> In my 93 V8 ZJ, the following error messages flash in and out the VIC
>> once a while.
>>
>> 1, Service 4 wheel drive switch, and
>> 2, bad coolant sersor
>>
>> I don't notice if I have a 4 wheel drive switch?! I only have 4hi and
>> 4lo. Since they flash in and out, does it indicate a bad connection @
>> somewhere?
>
> You have the Quadratrack transfer case. Problem is the sensor is
> internal to the xfr case. I'd remove/clean/reinstall the connector
> first. It's an oval 4pin located on the transfer case. not too easy
> to get at though.
>
> On the bright side, the 4wd and coolant sensor errors are not
> critical providing the range selection is correct, the fluid
> has been changed regularly, and you keep an eye on the overflow
> bottle so the level is between fill and add with the engine at
> operating temp.
>
> As for 2, clean the contacts on the sensor that is on the
> coolant reservoir, it's likely a bit corroded.
If it is the same sensor used on the WJ... When I got the error I just
disassembled and cleaned it really well in the basement and reinstalled it.
Been working fine for almost 2 years now.
Sensor in the WJ fits into the expansion tank.
http://s112.photobucket.com/albums/n...lantandTee.jpg
04-14-2007, 01:19 PM
#6
Guest
Posts: n/a
Re: 93ZJ - 4 wheel drive switch + bad coolant sersor
"DougW" <post.replies@invalid.address> wrote in message
news:QM_Th.113259$nh4.84489@newsfe20.lga...
> Bogey Buster wrote:
>> Hi Folk,
>>
>> In my 93 V8 ZJ, the following error messages flash in and out the VIC
>> once a while.
>>
>> 1, Service 4 wheel drive switch, and
>> 2, bad coolant sersor
>>
>> I don't notice if I have a 4 wheel drive switch?! I only have 4hi and
>> 4lo. Since they flash in and out, does it indicate a bad connection @
>> somewhere?
>
> You have the Quadratrack transfer case. Problem is the sensor is
> internal to the xfr case. I'd remove/clean/reinstall the connector
> first. It's an oval 4pin located on the transfer case. not too easy
> to get at though.
>
> On the bright side, the 4wd and coolant sensor errors are not
> critical providing the range selection is correct, the fluid
> has been changed regularly, and you keep an eye on the overflow
> bottle so the level is between fill and add with the engine at
> operating temp.
>
> As for 2, clean the contacts on the sensor that is on the
> coolant reservoir, it's likely a bit corroded.
If it is the same sensor used on the WJ... When I got the error I just
disassembled and cleaned it really well in the basement and reinstalled it.
Been working fine for almost 2 years now.
Sensor in the WJ fits into the expansion tank.
http://s112.photobucket.com/albums/n...lantandTee.jpg
04-14-2007, 01:19 PM
#7
Guest
Posts: n/a
Re: 93ZJ - 4 wheel drive switch + bad coolant sersor
"DougW" <post.replies@invalid.address> wrote in message
news:QM_Th.113259$nh4.84489@newsfe20.lga...
> Bogey Buster wrote:
>> Hi Folk,
>>
>> In my 93 V8 ZJ, the following error messages flash in and out the VIC
>> once a while.
>>
>> 1, Service 4 wheel drive switch, and
>> 2, bad coolant sersor
>>
>> I don't notice if I have a 4 wheel drive switch?! I only have 4hi and
>> 4lo. Since they flash in and out, does it indicate a bad connection @
>> somewhere?
>
> You have the Quadratrack transfer case. Problem is the sensor is
> internal to the xfr case. I'd remove/clean/reinstall the connector
> first. It's an oval 4pin located on the transfer case. not too easy
> to get at though.
>
> On the bright side, the 4wd and coolant sensor errors are not
> critical providing the range selection is correct, the fluid
> has been changed regularly, and you keep an eye on the overflow
> bottle so the level is between fill and add with the engine at
> operating temp.
>
> As for 2, clean the contacts on the sensor that is on the
> coolant reservoir, it's likely a bit corroded.
If it is the same sensor used on the WJ... When I got the error I just
disassembled and cleaned it really well in the basement and reinstalled it.
Been working fine for almost 2 years now.
Sensor in the WJ fits into the expansion tank.
http://s112.photobucket.com/albums/n...lantandTee.jpg
04-14-2007, 01:59 PM
#8
Guest
Posts: n/a
Re: 93ZJ - 4 wheel drive switch + bad coolant sersor
billy ray wrote:
> "DougW" <post.replies@invalid.address> wrote in message
> news:QM_Th.113259$nh4.84489@newsfe20.lga...
>> Bogey Buster wrote:
>>> Hi Folk,
>>>
>>> In my 93 V8 ZJ, the following error messages flash in and out the
>>> VIC once a while.
>>>
>>> 1, Service 4 wheel drive switch, and
>>> 2, bad coolant sersor
>>>
>>> I don't notice if I have a 4 wheel drive switch?! I only have 4hi
>>> and 4lo. Since they flash in and out, does it indicate a bad
>>> connection @ somewhere?
>>
>> You have the Quadratrack transfer case. Problem is the sensor is
>> internal to the xfr case. I'd remove/clean/reinstall the connector
>> first. It's an oval 4pin located on the transfer case. not too easy
>> to get at though.
>>
>> On the bright side, the 4wd and coolant sensor errors are not
>> critical providing the range selection is correct, the fluid
>> has been changed regularly, and you keep an eye on the overflow
>> bottle so the level is between fill and add with the engine at
>> operating temp.
>>
>> As for 2, clean the contacts on the sensor that is on the
>> coolant reservoir, it's likely a bit corroded.
>
> If it is the same sensor used on the WJ... When I got the error I just
> disassembled and cleaned it really well in the basement and
> reinstalled it. Been working fine for almost 2 years now.
>
> Sensor in the WJ fits into the expansion tank.
> http://s112.photobucket.com/albums/n...lantandTee.jpg
probably the same.
http://revbeergoggles.com/Fixes/sensor-coolant.jpg
--
DougW
> "DougW" <post.replies@invalid.address> wrote in message
> news:QM_Th.113259$nh4.84489@newsfe20.lga...
>> Bogey Buster wrote:
>>> Hi Folk,
>>>
>>> In my 93 V8 ZJ, the following error messages flash in and out the
>>> VIC once a while.
>>>
>>> 1, Service 4 wheel drive switch, and
>>> 2, bad coolant sersor
>>>
>>> I don't notice if I have a 4 wheel drive switch?! I only have 4hi
>>> and 4lo. Since they flash in and out, does it indicate a bad
>>> connection @ somewhere?
>>
>> You have the Quadratrack transfer case. Problem is the sensor is
>> internal to the xfr case. I'd remove/clean/reinstall the connector
>> first. It's an oval 4pin located on the transfer case. not too easy
>> to get at though.
>>
>> On the bright side, the 4wd and coolant sensor errors are not
>> critical providing the range selection is correct, the fluid
>> has been changed regularly, and you keep an eye on the overflow
>> bottle so the level is between fill and add with the engine at
>> operating temp.
>>
>> As for 2, clean the contacts on the sensor that is on the
>> coolant reservoir, it's likely a bit corroded.
>
> If it is the same sensor used on the WJ... When I got the error I just
> disassembled and cleaned it really well in the basement and
> reinstalled it. Been working fine for almost 2 years now.
>
> Sensor in the WJ fits into the expansion tank.
> http://s112.photobucket.com/albums/n...lantandTee.jpg
probably the same.
http://revbeergoggles.com/Fixes/sensor-coolant.jpg
--
DougW
04-14-2007, 01:59 PM
#9
Guest
Posts: n/a
Re: 93ZJ - 4 wheel drive switch + bad coolant sersor
billy ray wrote:
> "DougW" <post.replies@invalid.address> wrote in message
> news:QM_Th.113259$nh4.84489@newsfe20.lga...
>> Bogey Buster wrote:
>>> Hi Folk,
>>>
>>> In my 93 V8 ZJ, the following error messages flash in and out the
>>> VIC once a while.
>>>
>>> 1, Service 4 wheel drive switch, and
>>> 2, bad coolant sersor
>>>
>>> I don't notice if I have a 4 wheel drive switch?! I only have 4hi
>>> and 4lo. Since they flash in and out, does it indicate a bad
>>> connection @ somewhere?
>>
>> You have the Quadratrack transfer case. Problem is the sensor is
>> internal to the xfr case. I'd remove/clean/reinstall the connector
>> first. It's an oval 4pin located on the transfer case. not too easy
>> to get at though.
>>
>> On the bright side, the 4wd and coolant sensor errors are not
>> critical providing the range selection is correct, the fluid
>> has been changed regularly, and you keep an eye on the overflow
>> bottle so the level is between fill and add with the engine at
>> operating temp.
>>
>> As for 2, clean the contacts on the sensor that is on the
>> coolant reservoir, it's likely a bit corroded.
>
> If it is the same sensor used on the WJ... When I got the error I just
> disassembled and cleaned it really well in the basement and
> reinstalled it. Been working fine for almost 2 years now.
>
> Sensor in the WJ fits into the expansion tank.
> http://s112.photobucket.com/albums/n...lantandTee.jpg
probably the same.
http://revbeergoggles.com/Fixes/sensor-coolant.jpg
--
DougW
> "DougW" <post.replies@invalid.address> wrote in message
> news:QM_Th.113259$nh4.84489@newsfe20.lga...
>> Bogey Buster wrote:
>>> Hi Folk,
>>>
>>> In my 93 V8 ZJ, the following error messages flash in and out the
>>> VIC once a while.
>>>
>>> 1, Service 4 wheel drive switch, and
>>> 2, bad coolant sersor
>>>
>>> I don't notice if I have a 4 wheel drive switch?! I only have 4hi
>>> and 4lo. Since they flash in and out, does it indicate a bad
>>> connection @ somewhere?
>>
>> You have the Quadratrack transfer case. Problem is the sensor is
>> internal to the xfr case. I'd remove/clean/reinstall the connector
>> first. It's an oval 4pin located on the transfer case. not too easy
>> to get at though.
>>
>> On the bright side, the 4wd and coolant sensor errors are not
>> critical providing the range selection is correct, the fluid
>> has been changed regularly, and you keep an eye on the overflow
>> bottle so the level is between fill and add with the engine at
>> operating temp.
>>
>> As for 2, clean the contacts on the sensor that is on the
>> coolant reservoir, it's likely a bit corroded.
>
> If it is the same sensor used on the WJ... When I got the error I just
> disassembled and cleaned it really well in the basement and
> reinstalled it. Been working fine for almost 2 years now.
>
> Sensor in the WJ fits into the expansion tank.
> http://s112.photobucket.com/albums/n...lantandTee.jpg
probably the same.
http://revbeergoggles.com/Fixes/sensor-coolant.jpg
--
DougW
04-14-2007, 01:59 PM
#10
Guest
Posts: n/a
Re: 93ZJ - 4 wheel drive switch + bad coolant sersor
billy ray wrote:
> "DougW" <post.replies@invalid.address> wrote in message
> news:QM_Th.113259$nh4.84489@newsfe20.lga...
>> Bogey Buster wrote:
>>> Hi Folk,
>>>
>>> In my 93 V8 ZJ, the following error messages flash in and out the
>>> VIC once a while.
>>>
>>> 1, Service 4 wheel drive switch, and
>>> 2, bad coolant sersor
>>>
>>> I don't notice if I have a 4 wheel drive switch?! I only have 4hi
>>> and 4lo. Since they flash in and out, does it indicate a bad
>>> connection @ somewhere?
>>
>> You have the Quadratrack transfer case. Problem is the sensor is
>> internal to the xfr case. I'd remove/clean/reinstall the connector
>> first. It's an oval 4pin located on the transfer case. not too easy
>> to get at though.
>>
>> On the bright side, the 4wd and coolant sensor errors are not
>> critical providing the range selection is correct, the fluid
>> has been changed regularly, and you keep an eye on the overflow
>> bottle so the level is between fill and add with the engine at
>> operating temp.
>>
>> As for 2, clean the contacts on the sensor that is on the
>> coolant reservoir, it's likely a bit corroded.
>
> If it is the same sensor used on the WJ... When I got the error I just
> disassembled and cleaned it really well in the basement and
> reinstalled it. Been working fine for almost 2 years now.
>
> Sensor in the WJ fits into the expansion tank.
> http://s112.photobucket.com/albums/n...lantandTee.jpg
probably the same.
http://revbeergoggles.com/Fixes/sensor-coolant.jpg
--
DougW
> "DougW" <post.replies@invalid.address> wrote in message
> news:QM_Th.113259$nh4.84489@newsfe20.lga...
>> Bogey Buster wrote:
>>> Hi Folk,
>>>
>>> In my 93 V8 ZJ, the following error messages flash in and out the
>>> VIC once a while.
>>>
>>> 1, Service 4 wheel drive switch, and
>>> 2, bad coolant sersor
>>>
>>> I don't notice if I have a 4 wheel drive switch?! I only have 4hi
>>> and 4lo. Since they flash in and out, does it indicate a bad
>>> connection @ somewhere?
>>
>> You have the Quadratrack transfer case. Problem is the sensor is
>> internal to the xfr case. I'd remove/clean/reinstall the connector
>> first. It's an oval 4pin located on the transfer case. not too easy
>> to get at though.
>>
>> On the bright side, the 4wd and coolant sensor errors are not
>> critical providing the range selection is correct, the fluid
>> has been changed regularly, and you keep an eye on the overflow
>> bottle so the level is between fill and add with the engine at
>> operating temp.
>>
>> As for 2, clean the contacts on the sensor that is on the
>> coolant reservoir, it's likely a bit corroded.
>
> If it is the same sensor used on the WJ... When I got the error I just
> disassembled and cleaned it really well in the basement and
> reinstalled it. Been working fine for almost 2 years now.
>
> Sensor in the WJ fits into the expansion tank.
> http://s112.photobucket.com/albums/n...lantandTee.jpg
probably the same.
http://revbeergoggles.com/Fixes/sensor-coolant.jpg
--
DougW
