93 GC heater/ AC fan on all the time problem
04-08-2004, 09:54 PM
#21
Guest
Posts: n/a
Re: 93 GC heater/ AC fan on all the time problem
---- did pass the time by typing:
> The only thing I see between the Controller and the fan motor is
> something called a PWR MOD. The way it is drawn it looks like an
> integrated circuit. I think an A/D converter. However, the blower
> drive coming out of the controller on C9 shouldn't be calling for the
> fan to run when it shouldn't be. I still suspect the controller. It
> is subject to failure if you get water in that 60-pin connector.
The PWR mod takes a signal on the Brown(yellow stripe) wire from the
HEVAC controller, Pin 9. It's basically an SCR or power switching
module.
Have you checked the blower-high relay to see that it isn't stuck?
Don't exactly remember where that realay is. Think it was down by the
module wrapped up in tape. It's been a while and my ZJ doesn't have
the automagic climate stuff.
--
DougW
> The only thing I see between the Controller and the fan motor is
> something called a PWR MOD. The way it is drawn it looks like an
> integrated circuit. I think an A/D converter. However, the blower
> drive coming out of the controller on C9 shouldn't be calling for the
> fan to run when it shouldn't be. I still suspect the controller. It
> is subject to failure if you get water in that 60-pin connector.
The PWR mod takes a signal on the Brown(yellow stripe) wire from the
HEVAC controller, Pin 9. It's basically an SCR or power switching
module.
Have you checked the blower-high relay to see that it isn't stuck?
Don't exactly remember where that realay is. Think it was down by the
module wrapped up in tape. It's been a while and my ZJ doesn't have
the automagic climate stuff.
--
DougW
04-09-2004, 10:35 AM
#22
Guest
Posts: n/a
Re: 93 GC heater/ AC fan on all the time problem
Which brings me to a basic question. Where is the so called Fan Power
module located????
DougW wrote:
> ---- did pass the time by typing:
>
>
>>The only thing I see between the Controller and the fan motor is
>>something called a PWR MOD. The way it is drawn it looks like an
>>integrated circuit. I think an A/D converter. However, the blower
>>drive coming out of the controller on C9 shouldn't be calling for the
>>fan to run when it shouldn't be. I still suspect the controller. It
>>is subject to failure if you get water in that 60-pin connector.
>
>
> The PWR mod takes a signal on the Brown(yellow stripe) wire from the
> HEVAC controller, Pin 9. It's basically an SCR or power switching
> module.
>
> Have you checked the blower-high relay to see that it isn't stuck?
>
> Don't exactly remember where that realay is. Think it was down by the
> module wrapped up in tape. It's been a while and my ZJ doesn't have
> the automagic climate stuff.
>
module located????
DougW wrote:
> ---- did pass the time by typing:
>
>
>>The only thing I see between the Controller and the fan motor is
>>something called a PWR MOD. The way it is drawn it looks like an
>>integrated circuit. I think an A/D converter. However, the blower
>>drive coming out of the controller on C9 shouldn't be calling for the
>>fan to run when it shouldn't be. I still suspect the controller. It
>>is subject to failure if you get water in that 60-pin connector.
>
>
> The PWR mod takes a signal on the Brown(yellow stripe) wire from the
> HEVAC controller, Pin 9. It's basically an SCR or power switching
> module.
>
> Have you checked the blower-high relay to see that it isn't stuck?
>
> Don't exactly remember where that realay is. Think it was down by the
> module wrapped up in tape. It's been a while and my ZJ doesn't have
> the automagic climate stuff.
>
04-09-2004, 10:35 AM
#23
Guest
Posts: n/a
Re: 93 GC heater/ AC fan on all the time problem
Which brings me to a basic question. Where is the so called Fan Power
module located????
DougW wrote:
> ---- did pass the time by typing:
>
>
>>The only thing I see between the Controller and the fan motor is
>>something called a PWR MOD. The way it is drawn it looks like an
>>integrated circuit. I think an A/D converter. However, the blower
>>drive coming out of the controller on C9 shouldn't be calling for the
>>fan to run when it shouldn't be. I still suspect the controller. It
>>is subject to failure if you get water in that 60-pin connector.
>
>
> The PWR mod takes a signal on the Brown(yellow stripe) wire from the
> HEVAC controller, Pin 9. It's basically an SCR or power switching
> module.
>
> Have you checked the blower-high relay to see that it isn't stuck?
>
> Don't exactly remember where that realay is. Think it was down by the
> module wrapped up in tape. It's been a while and my ZJ doesn't have
> the automagic climate stuff.
>
module located????
DougW wrote:
> ---- did pass the time by typing:
>
>
>>The only thing I see between the Controller and the fan motor is
>>something called a PWR MOD. The way it is drawn it looks like an
>>integrated circuit. I think an A/D converter. However, the blower
>>drive coming out of the controller on C9 shouldn't be calling for the
>>fan to run when it shouldn't be. I still suspect the controller. It
>>is subject to failure if you get water in that 60-pin connector.
>
>
> The PWR mod takes a signal on the Brown(yellow stripe) wire from the
> HEVAC controller, Pin 9. It's basically an SCR or power switching
> module.
>
> Have you checked the blower-high relay to see that it isn't stuck?
>
> Don't exactly remember where that realay is. Think it was down by the
> module wrapped up in tape. It's been a while and my ZJ doesn't have
> the automagic climate stuff.
>
04-09-2004, 10:35 AM
#24
Guest
Posts: n/a
Re: 93 GC heater/ AC fan on all the time problem
Which brings me to a basic question. Where is the so called Fan Power
module located????
DougW wrote:
> ---- did pass the time by typing:
>
>
>>The only thing I see between the Controller and the fan motor is
>>something called a PWR MOD. The way it is drawn it looks like an
>>integrated circuit. I think an A/D converter. However, the blower
>>drive coming out of the controller on C9 shouldn't be calling for the
>>fan to run when it shouldn't be. I still suspect the controller. It
>>is subject to failure if you get water in that 60-pin connector.
>
>
> The PWR mod takes a signal on the Brown(yellow stripe) wire from the
> HEVAC controller, Pin 9. It's basically an SCR or power switching
> module.
>
> Have you checked the blower-high relay to see that it isn't stuck?
>
> Don't exactly remember where that realay is. Think it was down by the
> module wrapped up in tape. It's been a while and my ZJ doesn't have
> the automagic climate stuff.
>
module located????
DougW wrote:
> ---- did pass the time by typing:
>
>
>>The only thing I see between the Controller and the fan motor is
>>something called a PWR MOD. The way it is drawn it looks like an
>>integrated circuit. I think an A/D converter. However, the blower
>>drive coming out of the controller on C9 shouldn't be calling for the
>>fan to run when it shouldn't be. I still suspect the controller. It
>>is subject to failure if you get water in that 60-pin connector.
>
>
> The PWR mod takes a signal on the Brown(yellow stripe) wire from the
> HEVAC controller, Pin 9. It's basically an SCR or power switching
> module.
>
> Have you checked the blower-high relay to see that it isn't stuck?
>
> Don't exactly remember where that realay is. Think it was down by the
> module wrapped up in tape. It's been a while and my ZJ doesn't have
> the automagic climate stuff.
>
04-09-2004, 10:35 AM
#25
Guest
Posts: n/a
Re: 93 GC heater/ AC fan on all the time problem
Which brings me to a basic question. Where is the so called Fan Power
module located????
DougW wrote:
> ---- did pass the time by typing:
>
>
>>The only thing I see between the Controller and the fan motor is
>>something called a PWR MOD. The way it is drawn it looks like an
>>integrated circuit. I think an A/D converter. However, the blower
>>drive coming out of the controller on C9 shouldn't be calling for the
>>fan to run when it shouldn't be. I still suspect the controller. It
>>is subject to failure if you get water in that 60-pin connector.
>
>
> The PWR mod takes a signal on the Brown(yellow stripe) wire from the
> HEVAC controller, Pin 9. It's basically an SCR or power switching
> module.
>
> Have you checked the blower-high relay to see that it isn't stuck?
>
> Don't exactly remember where that realay is. Think it was down by the
> module wrapped up in tape. It's been a while and my ZJ doesn't have
> the automagic climate stuff.
>
module located????
DougW wrote:
> ---- did pass the time by typing:
>
>
>>The only thing I see between the Controller and the fan motor is
>>something called a PWR MOD. The way it is drawn it looks like an
>>integrated circuit. I think an A/D converter. However, the blower
>>drive coming out of the controller on C9 shouldn't be calling for the
>>fan to run when it shouldn't be. I still suspect the controller. It
>>is subject to failure if you get water in that 60-pin connector.
>
>
> The PWR mod takes a signal on the Brown(yellow stripe) wire from the
> HEVAC controller, Pin 9. It's basically an SCR or power switching
> module.
>
> Have you checked the blower-high relay to see that it isn't stuck?
>
> Don't exactly remember where that realay is. Think it was down by the
> module wrapped up in tape. It's been a while and my ZJ doesn't have
> the automagic climate stuff.
>
04-09-2004, 11:15 AM
#26
Guest
Posts: n/a
Re: 93 GC heater/ AC fan on all the time problem
http://www.----------.com/blower.pdf
God Bless America, ßill O|||||||O
mailto:--------------------
Walt Barie wrote:
>
> Which brings me to a basic question. Where is the so called Fan Power
> module located????
God Bless America, ßill O|||||||O
mailto:--------------------
Walt Barie wrote:
>
> Which brings me to a basic question. Where is the so called Fan Power
> module located????
04-09-2004, 11:15 AM
#27
Guest
Posts: n/a
Re: 93 GC heater/ AC fan on all the time problem
http://www.----------.com/blower.pdf
God Bless America, ßill O|||||||O
mailto:--------------------
Walt Barie wrote:
>
> Which brings me to a basic question. Where is the so called Fan Power
> module located????
God Bless America, ßill O|||||||O
mailto:--------------------
Walt Barie wrote:
>
> Which brings me to a basic question. Where is the so called Fan Power
> module located????
04-09-2004, 11:15 AM
#28
Guest
Posts: n/a
Re: 93 GC heater/ AC fan on all the time problem
http://www.----------.com/blower.pdf
God Bless America, ßill O|||||||O
mailto:--------------------
Walt Barie wrote:
>
> Which brings me to a basic question. Where is the so called Fan Power
> module located????
God Bless America, ßill O|||||||O
mailto:--------------------
Walt Barie wrote:
>
> Which brings me to a basic question. Where is the so called Fan Power
> module located????
04-09-2004, 11:15 AM
#29
Guest
Posts: n/a
Re: 93 GC heater/ AC fan on all the time problem
http://www.----------.com/blower.pdf
God Bless America, ßill O|||||||O
mailto:--------------------
Walt Barie wrote:
>
> Which brings me to a basic question. Where is the so called Fan Power
> module located????
God Bless America, ßill O|||||||O
mailto:--------------------
Walt Barie wrote:
>
> Which brings me to a basic question. Where is the so called Fan Power
> module located????
04-11-2004, 07:05 PM
#30
Guest
Posts: n/a
Re: 93 GC heater/ AC fan on all the time problem
OK found it. Thanks
L.W.(ßill) ------ III wrote:
> http://www.----------.com/blower.pdf
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> Walt Barie wrote:
>
>>Which brings me to a basic question. Where is the so called Fan Power
>>module located????
L.W.(ßill) ------ III wrote:
> http://www.----------.com/blower.pdf
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> Walt Barie wrote:
>
>>Which brings me to a basic question. Where is the so called Fan Power
>>module located????