4.56 gears in a Dana 30 front
#11
Guest
Posts: n/a
Re: 4.56 gears in a Dana 30 front
It's been a few years, but thinking back I'm sure I didn't have to replace
the entire reverse-cut D30 carrier when I installed the 4.56 R&P because I
installed a LockRight locker at the same time, which replaces the side and
spider gears. Didn't your LockRight install go this way too?
Terry 92YJ
(now running dual D60s w/Detroits)
"JimG" <jimg@cj7_2muchspam.com> wrote in message
news:pdFHb.32159$Wc4.17075@news01.roc.ny...
> You will have to get a new carrier for the D30, been there, done that.
>
> --
> JimG
> 80' CJ-7 258 CID
> 35" BFG MT on 15x10 Centerlines
> D44 Rear, Dana 30 Front. SOA
> 4.56 Gears, LockRight F&R
> Dana 300 w/4:1 & Currie twin sticks
> Warn X8000i w/ dual batteries
>
> "Tom P." <TPatzlaff@aol.com> wrote in message
> news:dd809f71.0312281017.6ee22391@posting.google.c om...
> > I have an "88" wrangler with a Dana 35 rear and Dana 30 front. I
> > currently have 3.55 gears in both diffs. and would like to put 4.56
> > gears in both.
> > The literature I can find says that if I have 3.55 or lower gears in
> > the D35, I will be ok. But what I need to know is if the 4.56 gears
> > will fit in the D30 case? From what I can find it sounds like I'm
> > going to need a housing with 3.73 or lower gears in it for the 4.56 to
> > fit.I need to find out the real answer.
> > Has anyone out there put 4.56 gears in these size housings?
> > Any help or advice would be great.
> > Tom
>
>
the entire reverse-cut D30 carrier when I installed the 4.56 R&P because I
installed a LockRight locker at the same time, which replaces the side and
spider gears. Didn't your LockRight install go this way too?
Terry 92YJ
(now running dual D60s w/Detroits)
"JimG" <jimg@cj7_2muchspam.com> wrote in message
news:pdFHb.32159$Wc4.17075@news01.roc.ny...
> You will have to get a new carrier for the D30, been there, done that.
>
> --
> JimG
> 80' CJ-7 258 CID
> 35" BFG MT on 15x10 Centerlines
> D44 Rear, Dana 30 Front. SOA
> 4.56 Gears, LockRight F&R
> Dana 300 w/4:1 & Currie twin sticks
> Warn X8000i w/ dual batteries
>
> "Tom P." <TPatzlaff@aol.com> wrote in message
> news:dd809f71.0312281017.6ee22391@posting.google.c om...
> > I have an "88" wrangler with a Dana 35 rear and Dana 30 front. I
> > currently have 3.55 gears in both diffs. and would like to put 4.56
> > gears in both.
> > The literature I can find says that if I have 3.55 or lower gears in
> > the D35, I will be ok. But what I need to know is if the 4.56 gears
> > will fit in the D30 case? From what I can find it sounds like I'm
> > going to need a housing with 3.73 or lower gears in it for the 4.56 to
> > fit.I need to find out the real answer.
> > Has anyone out there put 4.56 gears in these size housings?
> > Any help or advice would be great.
> > Tom
>
>
#12
Guest
Posts: n/a
Re: 4.56 gears in a Dana 30 front
It's been a few years, but thinking back I'm sure I didn't have to replace
the entire reverse-cut D30 carrier when I installed the 4.56 R&P because I
installed a LockRight locker at the same time, which replaces the side and
spider gears. Didn't your LockRight install go this way too?
Terry 92YJ
(now running dual D60s w/Detroits)
"JimG" <jimg@cj7_2muchspam.com> wrote in message
news:pdFHb.32159$Wc4.17075@news01.roc.ny...
> You will have to get a new carrier for the D30, been there, done that.
>
> --
> JimG
> 80' CJ-7 258 CID
> 35" BFG MT on 15x10 Centerlines
> D44 Rear, Dana 30 Front. SOA
> 4.56 Gears, LockRight F&R
> Dana 300 w/4:1 & Currie twin sticks
> Warn X8000i w/ dual batteries
>
> "Tom P." <TPatzlaff@aol.com> wrote in message
> news:dd809f71.0312281017.6ee22391@posting.google.c om...
> > I have an "88" wrangler with a Dana 35 rear and Dana 30 front. I
> > currently have 3.55 gears in both diffs. and would like to put 4.56
> > gears in both.
> > The literature I can find says that if I have 3.55 or lower gears in
> > the D35, I will be ok. But what I need to know is if the 4.56 gears
> > will fit in the D30 case? From what I can find it sounds like I'm
> > going to need a housing with 3.73 or lower gears in it for the 4.56 to
> > fit.I need to find out the real answer.
> > Has anyone out there put 4.56 gears in these size housings?
> > Any help or advice would be great.
> > Tom
>
>
the entire reverse-cut D30 carrier when I installed the 4.56 R&P because I
installed a LockRight locker at the same time, which replaces the side and
spider gears. Didn't your LockRight install go this way too?
Terry 92YJ
(now running dual D60s w/Detroits)
"JimG" <jimg@cj7_2muchspam.com> wrote in message
news:pdFHb.32159$Wc4.17075@news01.roc.ny...
> You will have to get a new carrier for the D30, been there, done that.
>
> --
> JimG
> 80' CJ-7 258 CID
> 35" BFG MT on 15x10 Centerlines
> D44 Rear, Dana 30 Front. SOA
> 4.56 Gears, LockRight F&R
> Dana 300 w/4:1 & Currie twin sticks
> Warn X8000i w/ dual batteries
>
> "Tom P." <TPatzlaff@aol.com> wrote in message
> news:dd809f71.0312281017.6ee22391@posting.google.c om...
> > I have an "88" wrangler with a Dana 35 rear and Dana 30 front. I
> > currently have 3.55 gears in both diffs. and would like to put 4.56
> > gears in both.
> > The literature I can find says that if I have 3.55 or lower gears in
> > the D35, I will be ok. But what I need to know is if the 4.56 gears
> > will fit in the D30 case? From what I can find it sounds like I'm
> > going to need a housing with 3.73 or lower gears in it for the 4.56 to
> > fit.I need to find out the real answer.
> > Has anyone out there put 4.56 gears in these size housings?
> > Any help or advice would be great.
> > Tom
>
>
#13
Guest
Posts: n/a
Re: 4.56 gears in a Dana 30 front
It's been a few years, but thinking back I'm sure I didn't have to replace
the entire reverse-cut D30 carrier when I installed the 4.56 R&P because I
installed a LockRight locker at the same time, which replaces the side and
spider gears. Didn't your LockRight install go this way too?
Terry 92YJ
(now running dual D60s w/Detroits)
"JimG" <jimg@cj7_2muchspam.com> wrote in message
news:pdFHb.32159$Wc4.17075@news01.roc.ny...
> You will have to get a new carrier for the D30, been there, done that.
>
> --
> JimG
> 80' CJ-7 258 CID
> 35" BFG MT on 15x10 Centerlines
> D44 Rear, Dana 30 Front. SOA
> 4.56 Gears, LockRight F&R
> Dana 300 w/4:1 & Currie twin sticks
> Warn X8000i w/ dual batteries
>
> "Tom P." <TPatzlaff@aol.com> wrote in message
> news:dd809f71.0312281017.6ee22391@posting.google.c om...
> > I have an "88" wrangler with a Dana 35 rear and Dana 30 front. I
> > currently have 3.55 gears in both diffs. and would like to put 4.56
> > gears in both.
> > The literature I can find says that if I have 3.55 or lower gears in
> > the D35, I will be ok. But what I need to know is if the 4.56 gears
> > will fit in the D30 case? From what I can find it sounds like I'm
> > going to need a housing with 3.73 or lower gears in it for the 4.56 to
> > fit.I need to find out the real answer.
> > Has anyone out there put 4.56 gears in these size housings?
> > Any help or advice would be great.
> > Tom
>
>
the entire reverse-cut D30 carrier when I installed the 4.56 R&P because I
installed a LockRight locker at the same time, which replaces the side and
spider gears. Didn't your LockRight install go this way too?
Terry 92YJ
(now running dual D60s w/Detroits)
"JimG" <jimg@cj7_2muchspam.com> wrote in message
news:pdFHb.32159$Wc4.17075@news01.roc.ny...
> You will have to get a new carrier for the D30, been there, done that.
>
> --
> JimG
> 80' CJ-7 258 CID
> 35" BFG MT on 15x10 Centerlines
> D44 Rear, Dana 30 Front. SOA
> 4.56 Gears, LockRight F&R
> Dana 300 w/4:1 & Currie twin sticks
> Warn X8000i w/ dual batteries
>
> "Tom P." <TPatzlaff@aol.com> wrote in message
> news:dd809f71.0312281017.6ee22391@posting.google.c om...
> > I have an "88" wrangler with a Dana 35 rear and Dana 30 front. I
> > currently have 3.55 gears in both diffs. and would like to put 4.56
> > gears in both.
> > The literature I can find says that if I have 3.55 or lower gears in
> > the D35, I will be ok. But what I need to know is if the 4.56 gears
> > will fit in the D30 case? From what I can find it sounds like I'm
> > going to need a housing with 3.73 or lower gears in it for the 4.56 to
> > fit.I need to find out the real answer.
> > Has anyone out there put 4.56 gears in these size housings?
> > Any help or advice would be great.
> > Tom
>
>
#14
Guest
Posts: n/a
Re: 4.56 gears in a Dana 30 front
If original gear is higher that 3.73, the carrier has to be replaced. My
original gear was 3.07. I had to replace the carriers in both front and
rear.
JimG
"Terry Jeffrey" <twjeffrey@hotmail.com> wrote in message
news:XZFHb.22399$Pg1.9205@newsread1.news.pas.earth link.net...
> It's been a few years, but thinking back I'm sure I didn't have to replace
> the entire reverse-cut D30 carrier when I installed the 4.56 R&P because I
> installed a LockRight locker at the same time, which replaces the side and
> spider gears. Didn't your LockRight install go this way too?
>
> Terry 92YJ
> (now running dual D60s w/Detroits)
>
>
> "JimG" <jimg@cj7_2muchspam.com> wrote in message
> news:pdFHb.32159$Wc4.17075@news01.roc.ny...
> > You will have to get a new carrier for the D30, been there, done that.
> >
> > --
> > JimG
> > 80' CJ-7 258 CID
> > 35" BFG MT on 15x10 Centerlines
> > D44 Rear, Dana 30 Front. SOA
> > 4.56 Gears, LockRight F&R
> > Dana 300 w/4:1 & Currie twin sticks
> > Warn X8000i w/ dual batteries
> >
> > "Tom P." <TPatzlaff@aol.com> wrote in message
> > news:dd809f71.0312281017.6ee22391@posting.google.c om...
> > > I have an "88" wrangler with a Dana 35 rear and Dana 30 front. I
> > > currently have 3.55 gears in both diffs. and would like to put 4.56
> > > gears in both.
> > > The literature I can find says that if I have 3.55 or lower gears in
> > > the D35, I will be ok. But what I need to know is if the 4.56 gears
> > > will fit in the D30 case? From what I can find it sounds like I'm
> > > going to need a housing with 3.73 or lower gears in it for the 4.56 to
> > > fit.I need to find out the real answer.
> > > Has anyone out there put 4.56 gears in these size housings?
> > > Any help or advice would be great.
> > > Tom
> >
> >
>
>
original gear was 3.07. I had to replace the carriers in both front and
rear.
JimG
"Terry Jeffrey" <twjeffrey@hotmail.com> wrote in message
news:XZFHb.22399$Pg1.9205@newsread1.news.pas.earth link.net...
> It's been a few years, but thinking back I'm sure I didn't have to replace
> the entire reverse-cut D30 carrier when I installed the 4.56 R&P because I
> installed a LockRight locker at the same time, which replaces the side and
> spider gears. Didn't your LockRight install go this way too?
>
> Terry 92YJ
> (now running dual D60s w/Detroits)
>
>
> "JimG" <jimg@cj7_2muchspam.com> wrote in message
> news:pdFHb.32159$Wc4.17075@news01.roc.ny...
> > You will have to get a new carrier for the D30, been there, done that.
> >
> > --
> > JimG
> > 80' CJ-7 258 CID
> > 35" BFG MT on 15x10 Centerlines
> > D44 Rear, Dana 30 Front. SOA
> > 4.56 Gears, LockRight F&R
> > Dana 300 w/4:1 & Currie twin sticks
> > Warn X8000i w/ dual batteries
> >
> > "Tom P." <TPatzlaff@aol.com> wrote in message
> > news:dd809f71.0312281017.6ee22391@posting.google.c om...
> > > I have an "88" wrangler with a Dana 35 rear and Dana 30 front. I
> > > currently have 3.55 gears in both diffs. and would like to put 4.56
> > > gears in both.
> > > The literature I can find says that if I have 3.55 or lower gears in
> > > the D35, I will be ok. But what I need to know is if the 4.56 gears
> > > will fit in the D30 case? From what I can find it sounds like I'm
> > > going to need a housing with 3.73 or lower gears in it for the 4.56 to
> > > fit.I need to find out the real answer.
> > > Has anyone out there put 4.56 gears in these size housings?
> > > Any help or advice would be great.
> > > Tom
> >
> >
>
>
#15
Guest
Posts: n/a
Re: 4.56 gears in a Dana 30 front
If original gear is higher that 3.73, the carrier has to be replaced. My
original gear was 3.07. I had to replace the carriers in both front and
rear.
JimG
"Terry Jeffrey" <twjeffrey@hotmail.com> wrote in message
news:XZFHb.22399$Pg1.9205@newsread1.news.pas.earth link.net...
> It's been a few years, but thinking back I'm sure I didn't have to replace
> the entire reverse-cut D30 carrier when I installed the 4.56 R&P because I
> installed a LockRight locker at the same time, which replaces the side and
> spider gears. Didn't your LockRight install go this way too?
>
> Terry 92YJ
> (now running dual D60s w/Detroits)
>
>
> "JimG" <jimg@cj7_2muchspam.com> wrote in message
> news:pdFHb.32159$Wc4.17075@news01.roc.ny...
> > You will have to get a new carrier for the D30, been there, done that.
> >
> > --
> > JimG
> > 80' CJ-7 258 CID
> > 35" BFG MT on 15x10 Centerlines
> > D44 Rear, Dana 30 Front. SOA
> > 4.56 Gears, LockRight F&R
> > Dana 300 w/4:1 & Currie twin sticks
> > Warn X8000i w/ dual batteries
> >
> > "Tom P." <TPatzlaff@aol.com> wrote in message
> > news:dd809f71.0312281017.6ee22391@posting.google.c om...
> > > I have an "88" wrangler with a Dana 35 rear and Dana 30 front. I
> > > currently have 3.55 gears in both diffs. and would like to put 4.56
> > > gears in both.
> > > The literature I can find says that if I have 3.55 or lower gears in
> > > the D35, I will be ok. But what I need to know is if the 4.56 gears
> > > will fit in the D30 case? From what I can find it sounds like I'm
> > > going to need a housing with 3.73 or lower gears in it for the 4.56 to
> > > fit.I need to find out the real answer.
> > > Has anyone out there put 4.56 gears in these size housings?
> > > Any help or advice would be great.
> > > Tom
> >
> >
>
>
original gear was 3.07. I had to replace the carriers in both front and
rear.
JimG
"Terry Jeffrey" <twjeffrey@hotmail.com> wrote in message
news:XZFHb.22399$Pg1.9205@newsread1.news.pas.earth link.net...
> It's been a few years, but thinking back I'm sure I didn't have to replace
> the entire reverse-cut D30 carrier when I installed the 4.56 R&P because I
> installed a LockRight locker at the same time, which replaces the side and
> spider gears. Didn't your LockRight install go this way too?
>
> Terry 92YJ
> (now running dual D60s w/Detroits)
>
>
> "JimG" <jimg@cj7_2muchspam.com> wrote in message
> news:pdFHb.32159$Wc4.17075@news01.roc.ny...
> > You will have to get a new carrier for the D30, been there, done that.
> >
> > --
> > JimG
> > 80' CJ-7 258 CID
> > 35" BFG MT on 15x10 Centerlines
> > D44 Rear, Dana 30 Front. SOA
> > 4.56 Gears, LockRight F&R
> > Dana 300 w/4:1 & Currie twin sticks
> > Warn X8000i w/ dual batteries
> >
> > "Tom P." <TPatzlaff@aol.com> wrote in message
> > news:dd809f71.0312281017.6ee22391@posting.google.c om...
> > > I have an "88" wrangler with a Dana 35 rear and Dana 30 front. I
> > > currently have 3.55 gears in both diffs. and would like to put 4.56
> > > gears in both.
> > > The literature I can find says that if I have 3.55 or lower gears in
> > > the D35, I will be ok. But what I need to know is if the 4.56 gears
> > > will fit in the D30 case? From what I can find it sounds like I'm
> > > going to need a housing with 3.73 or lower gears in it for the 4.56 to
> > > fit.I need to find out the real answer.
> > > Has anyone out there put 4.56 gears in these size housings?
> > > Any help or advice would be great.
> > > Tom
> >
> >
>
>
#16
Guest
Posts: n/a
Re: 4.56 gears in a Dana 30 front
If original gear is higher that 3.73, the carrier has to be replaced. My
original gear was 3.07. I had to replace the carriers in both front and
rear.
JimG
"Terry Jeffrey" <twjeffrey@hotmail.com> wrote in message
news:XZFHb.22399$Pg1.9205@newsread1.news.pas.earth link.net...
> It's been a few years, but thinking back I'm sure I didn't have to replace
> the entire reverse-cut D30 carrier when I installed the 4.56 R&P because I
> installed a LockRight locker at the same time, which replaces the side and
> spider gears. Didn't your LockRight install go this way too?
>
> Terry 92YJ
> (now running dual D60s w/Detroits)
>
>
> "JimG" <jimg@cj7_2muchspam.com> wrote in message
> news:pdFHb.32159$Wc4.17075@news01.roc.ny...
> > You will have to get a new carrier for the D30, been there, done that.
> >
> > --
> > JimG
> > 80' CJ-7 258 CID
> > 35" BFG MT on 15x10 Centerlines
> > D44 Rear, Dana 30 Front. SOA
> > 4.56 Gears, LockRight F&R
> > Dana 300 w/4:1 & Currie twin sticks
> > Warn X8000i w/ dual batteries
> >
> > "Tom P." <TPatzlaff@aol.com> wrote in message
> > news:dd809f71.0312281017.6ee22391@posting.google.c om...
> > > I have an "88" wrangler with a Dana 35 rear and Dana 30 front. I
> > > currently have 3.55 gears in both diffs. and would like to put 4.56
> > > gears in both.
> > > The literature I can find says that if I have 3.55 or lower gears in
> > > the D35, I will be ok. But what I need to know is if the 4.56 gears
> > > will fit in the D30 case? From what I can find it sounds like I'm
> > > going to need a housing with 3.73 or lower gears in it for the 4.56 to
> > > fit.I need to find out the real answer.
> > > Has anyone out there put 4.56 gears in these size housings?
> > > Any help or advice would be great.
> > > Tom
> >
> >
>
>
original gear was 3.07. I had to replace the carriers in both front and
rear.
JimG
"Terry Jeffrey" <twjeffrey@hotmail.com> wrote in message
news:XZFHb.22399$Pg1.9205@newsread1.news.pas.earth link.net...
> It's been a few years, but thinking back I'm sure I didn't have to replace
> the entire reverse-cut D30 carrier when I installed the 4.56 R&P because I
> installed a LockRight locker at the same time, which replaces the side and
> spider gears. Didn't your LockRight install go this way too?
>
> Terry 92YJ
> (now running dual D60s w/Detroits)
>
>
> "JimG" <jimg@cj7_2muchspam.com> wrote in message
> news:pdFHb.32159$Wc4.17075@news01.roc.ny...
> > You will have to get a new carrier for the D30, been there, done that.
> >
> > --
> > JimG
> > 80' CJ-7 258 CID
> > 35" BFG MT on 15x10 Centerlines
> > D44 Rear, Dana 30 Front. SOA
> > 4.56 Gears, LockRight F&R
> > Dana 300 w/4:1 & Currie twin sticks
> > Warn X8000i w/ dual batteries
> >
> > "Tom P." <TPatzlaff@aol.com> wrote in message
> > news:dd809f71.0312281017.6ee22391@posting.google.c om...
> > > I have an "88" wrangler with a Dana 35 rear and Dana 30 front. I
> > > currently have 3.55 gears in both diffs. and would like to put 4.56
> > > gears in both.
> > > The literature I can find says that if I have 3.55 or lower gears in
> > > the D35, I will be ok. But what I need to know is if the 4.56 gears
> > > will fit in the D30 case? From what I can find it sounds like I'm
> > > going to need a housing with 3.73 or lower gears in it for the 4.56 to
> > > fit.I need to find out the real answer.
> > > Has anyone out there put 4.56 gears in these size housings?
> > > Any help or advice would be great.
> > > Tom
> >
> >
>
>
#17
Guest
Posts: n/a
Re: 4.56 gears in a Dana 30 front
My original gear was 3.07 too, but I'm certain I did not have to replace the
D30 carrier in conjunction with using the LockRite. Maybe this is a
difference in the stock '80 vs '92 D30?
Terry.
"JimG" <jimg@cj7_2muchspam.com> wrote in message
news:FzHHb.32183$iN4.2074@news01.roc.ny...
> If original gear is higher that 3.73, the carrier has to be replaced. My
> original gear was 3.07. I had to replace the carriers in both front and
> rear.
>
> JimG
>
> "Terry Jeffrey" <twjeffrey@hotmail.com> wrote in message
> news:XZFHb.22399$Pg1.9205@newsread1.news.pas.earth link.net...
> > It's been a few years, but thinking back I'm sure I didn't have to
replace
> > the entire reverse-cut D30 carrier when I installed the 4.56 R&P because
I
> > installed a LockRight locker at the same time, which replaces the side
and
> > spider gears. Didn't your LockRight install go this way too?
> >
> > Terry 92YJ
> > (now running dual D60s w/Detroits)
> >
> >
> > "JimG" <jimg@cj7_2muchspam.com> wrote in message
> > news:pdFHb.32159$Wc4.17075@news01.roc.ny...
> > > You will have to get a new carrier for the D30, been there, done that.
> > >
> > > --
> > > JimG
> > > 80' CJ-7 258 CID
> > > 35" BFG MT on 15x10 Centerlines
> > > D44 Rear, Dana 30 Front. SOA
> > > 4.56 Gears, LockRight F&R
> > > Dana 300 w/4:1 & Currie twin sticks
> > > Warn X8000i w/ dual batteries
> > >
> > > "Tom P." <TPatzlaff@aol.com> wrote in message
> > > news:dd809f71.0312281017.6ee22391@posting.google.c om...
> > > > I have an "88" wrangler with a Dana 35 rear and Dana 30 front. I
> > > > currently have 3.55 gears in both diffs. and would like to put 4.56
> > > > gears in both.
> > > > The literature I can find says that if I have 3.55 or lower gears
in
> > > > the D35, I will be ok. But what I need to know is if the 4.56 gears
> > > > will fit in the D30 case? From what I can find it sounds like I'm
> > > > going to need a housing with 3.73 or lower gears in it for the 4.56
to
> > > > fit.I need to find out the real answer.
> > > > Has anyone out there put 4.56 gears in these size housings?
> > > > Any help or advice would be great.
> > > > Tom
> > >
> > >
> >
> >
>
>
D30 carrier in conjunction with using the LockRite. Maybe this is a
difference in the stock '80 vs '92 D30?
Terry.
"JimG" <jimg@cj7_2muchspam.com> wrote in message
news:FzHHb.32183$iN4.2074@news01.roc.ny...
> If original gear is higher that 3.73, the carrier has to be replaced. My
> original gear was 3.07. I had to replace the carriers in both front and
> rear.
>
> JimG
>
> "Terry Jeffrey" <twjeffrey@hotmail.com> wrote in message
> news:XZFHb.22399$Pg1.9205@newsread1.news.pas.earth link.net...
> > It's been a few years, but thinking back I'm sure I didn't have to
replace
> > the entire reverse-cut D30 carrier when I installed the 4.56 R&P because
I
> > installed a LockRight locker at the same time, which replaces the side
and
> > spider gears. Didn't your LockRight install go this way too?
> >
> > Terry 92YJ
> > (now running dual D60s w/Detroits)
> >
> >
> > "JimG" <jimg@cj7_2muchspam.com> wrote in message
> > news:pdFHb.32159$Wc4.17075@news01.roc.ny...
> > > You will have to get a new carrier for the D30, been there, done that.
> > >
> > > --
> > > JimG
> > > 80' CJ-7 258 CID
> > > 35" BFG MT on 15x10 Centerlines
> > > D44 Rear, Dana 30 Front. SOA
> > > 4.56 Gears, LockRight F&R
> > > Dana 300 w/4:1 & Currie twin sticks
> > > Warn X8000i w/ dual batteries
> > >
> > > "Tom P." <TPatzlaff@aol.com> wrote in message
> > > news:dd809f71.0312281017.6ee22391@posting.google.c om...
> > > > I have an "88" wrangler with a Dana 35 rear and Dana 30 front. I
> > > > currently have 3.55 gears in both diffs. and would like to put 4.56
> > > > gears in both.
> > > > The literature I can find says that if I have 3.55 or lower gears
in
> > > > the D35, I will be ok. But what I need to know is if the 4.56 gears
> > > > will fit in the D30 case? From what I can find it sounds like I'm
> > > > going to need a housing with 3.73 or lower gears in it for the 4.56
to
> > > > fit.I need to find out the real answer.
> > > > Has anyone out there put 4.56 gears in these size housings?
> > > > Any help or advice would be great.
> > > > Tom
> > >
> > >
> >
> >
>
>
#18
Guest
Posts: n/a
Re: 4.56 gears in a Dana 30 front
My original gear was 3.07 too, but I'm certain I did not have to replace the
D30 carrier in conjunction with using the LockRite. Maybe this is a
difference in the stock '80 vs '92 D30?
Terry.
"JimG" <jimg@cj7_2muchspam.com> wrote in message
news:FzHHb.32183$iN4.2074@news01.roc.ny...
> If original gear is higher that 3.73, the carrier has to be replaced. My
> original gear was 3.07. I had to replace the carriers in both front and
> rear.
>
> JimG
>
> "Terry Jeffrey" <twjeffrey@hotmail.com> wrote in message
> news:XZFHb.22399$Pg1.9205@newsread1.news.pas.earth link.net...
> > It's been a few years, but thinking back I'm sure I didn't have to
replace
> > the entire reverse-cut D30 carrier when I installed the 4.56 R&P because
I
> > installed a LockRight locker at the same time, which replaces the side
and
> > spider gears. Didn't your LockRight install go this way too?
> >
> > Terry 92YJ
> > (now running dual D60s w/Detroits)
> >
> >
> > "JimG" <jimg@cj7_2muchspam.com> wrote in message
> > news:pdFHb.32159$Wc4.17075@news01.roc.ny...
> > > You will have to get a new carrier for the D30, been there, done that.
> > >
> > > --
> > > JimG
> > > 80' CJ-7 258 CID
> > > 35" BFG MT on 15x10 Centerlines
> > > D44 Rear, Dana 30 Front. SOA
> > > 4.56 Gears, LockRight F&R
> > > Dana 300 w/4:1 & Currie twin sticks
> > > Warn X8000i w/ dual batteries
> > >
> > > "Tom P." <TPatzlaff@aol.com> wrote in message
> > > news:dd809f71.0312281017.6ee22391@posting.google.c om...
> > > > I have an "88" wrangler with a Dana 35 rear and Dana 30 front. I
> > > > currently have 3.55 gears in both diffs. and would like to put 4.56
> > > > gears in both.
> > > > The literature I can find says that if I have 3.55 or lower gears
in
> > > > the D35, I will be ok. But what I need to know is if the 4.56 gears
> > > > will fit in the D30 case? From what I can find it sounds like I'm
> > > > going to need a housing with 3.73 or lower gears in it for the 4.56
to
> > > > fit.I need to find out the real answer.
> > > > Has anyone out there put 4.56 gears in these size housings?
> > > > Any help or advice would be great.
> > > > Tom
> > >
> > >
> >
> >
>
>
D30 carrier in conjunction with using the LockRite. Maybe this is a
difference in the stock '80 vs '92 D30?
Terry.
"JimG" <jimg@cj7_2muchspam.com> wrote in message
news:FzHHb.32183$iN4.2074@news01.roc.ny...
> If original gear is higher that 3.73, the carrier has to be replaced. My
> original gear was 3.07. I had to replace the carriers in both front and
> rear.
>
> JimG
>
> "Terry Jeffrey" <twjeffrey@hotmail.com> wrote in message
> news:XZFHb.22399$Pg1.9205@newsread1.news.pas.earth link.net...
> > It's been a few years, but thinking back I'm sure I didn't have to
replace
> > the entire reverse-cut D30 carrier when I installed the 4.56 R&P because
I
> > installed a LockRight locker at the same time, which replaces the side
and
> > spider gears. Didn't your LockRight install go this way too?
> >
> > Terry 92YJ
> > (now running dual D60s w/Detroits)
> >
> >
> > "JimG" <jimg@cj7_2muchspam.com> wrote in message
> > news:pdFHb.32159$Wc4.17075@news01.roc.ny...
> > > You will have to get a new carrier for the D30, been there, done that.
> > >
> > > --
> > > JimG
> > > 80' CJ-7 258 CID
> > > 35" BFG MT on 15x10 Centerlines
> > > D44 Rear, Dana 30 Front. SOA
> > > 4.56 Gears, LockRight F&R
> > > Dana 300 w/4:1 & Currie twin sticks
> > > Warn X8000i w/ dual batteries
> > >
> > > "Tom P." <TPatzlaff@aol.com> wrote in message
> > > news:dd809f71.0312281017.6ee22391@posting.google.c om...
> > > > I have an "88" wrangler with a Dana 35 rear and Dana 30 front. I
> > > > currently have 3.55 gears in both diffs. and would like to put 4.56
> > > > gears in both.
> > > > The literature I can find says that if I have 3.55 or lower gears
in
> > > > the D35, I will be ok. But what I need to know is if the 4.56 gears
> > > > will fit in the D30 case? From what I can find it sounds like I'm
> > > > going to need a housing with 3.73 or lower gears in it for the 4.56
to
> > > > fit.I need to find out the real answer.
> > > > Has anyone out there put 4.56 gears in these size housings?
> > > > Any help or advice would be great.
> > > > Tom
> > >
> > >
> >
> >
>
>
#19
Guest
Posts: n/a
Re: 4.56 gears in a Dana 30 front
My original gear was 3.07 too, but I'm certain I did not have to replace the
D30 carrier in conjunction with using the LockRite. Maybe this is a
difference in the stock '80 vs '92 D30?
Terry.
"JimG" <jimg@cj7_2muchspam.com> wrote in message
news:FzHHb.32183$iN4.2074@news01.roc.ny...
> If original gear is higher that 3.73, the carrier has to be replaced. My
> original gear was 3.07. I had to replace the carriers in both front and
> rear.
>
> JimG
>
> "Terry Jeffrey" <twjeffrey@hotmail.com> wrote in message
> news:XZFHb.22399$Pg1.9205@newsread1.news.pas.earth link.net...
> > It's been a few years, but thinking back I'm sure I didn't have to
replace
> > the entire reverse-cut D30 carrier when I installed the 4.56 R&P because
I
> > installed a LockRight locker at the same time, which replaces the side
and
> > spider gears. Didn't your LockRight install go this way too?
> >
> > Terry 92YJ
> > (now running dual D60s w/Detroits)
> >
> >
> > "JimG" <jimg@cj7_2muchspam.com> wrote in message
> > news:pdFHb.32159$Wc4.17075@news01.roc.ny...
> > > You will have to get a new carrier for the D30, been there, done that.
> > >
> > > --
> > > JimG
> > > 80' CJ-7 258 CID
> > > 35" BFG MT on 15x10 Centerlines
> > > D44 Rear, Dana 30 Front. SOA
> > > 4.56 Gears, LockRight F&R
> > > Dana 300 w/4:1 & Currie twin sticks
> > > Warn X8000i w/ dual batteries
> > >
> > > "Tom P." <TPatzlaff@aol.com> wrote in message
> > > news:dd809f71.0312281017.6ee22391@posting.google.c om...
> > > > I have an "88" wrangler with a Dana 35 rear and Dana 30 front. I
> > > > currently have 3.55 gears in both diffs. and would like to put 4.56
> > > > gears in both.
> > > > The literature I can find says that if I have 3.55 or lower gears
in
> > > > the D35, I will be ok. But what I need to know is if the 4.56 gears
> > > > will fit in the D30 case? From what I can find it sounds like I'm
> > > > going to need a housing with 3.73 or lower gears in it for the 4.56
to
> > > > fit.I need to find out the real answer.
> > > > Has anyone out there put 4.56 gears in these size housings?
> > > > Any help or advice would be great.
> > > > Tom
> > >
> > >
> >
> >
>
>
D30 carrier in conjunction with using the LockRite. Maybe this is a
difference in the stock '80 vs '92 D30?
Terry.
"JimG" <jimg@cj7_2muchspam.com> wrote in message
news:FzHHb.32183$iN4.2074@news01.roc.ny...
> If original gear is higher that 3.73, the carrier has to be replaced. My
> original gear was 3.07. I had to replace the carriers in both front and
> rear.
>
> JimG
>
> "Terry Jeffrey" <twjeffrey@hotmail.com> wrote in message
> news:XZFHb.22399$Pg1.9205@newsread1.news.pas.earth link.net...
> > It's been a few years, but thinking back I'm sure I didn't have to
replace
> > the entire reverse-cut D30 carrier when I installed the 4.56 R&P because
I
> > installed a LockRight locker at the same time, which replaces the side
and
> > spider gears. Didn't your LockRight install go this way too?
> >
> > Terry 92YJ
> > (now running dual D60s w/Detroits)
> >
> >
> > "JimG" <jimg@cj7_2muchspam.com> wrote in message
> > news:pdFHb.32159$Wc4.17075@news01.roc.ny...
> > > You will have to get a new carrier for the D30, been there, done that.
> > >
> > > --
> > > JimG
> > > 80' CJ-7 258 CID
> > > 35" BFG MT on 15x10 Centerlines
> > > D44 Rear, Dana 30 Front. SOA
> > > 4.56 Gears, LockRight F&R
> > > Dana 300 w/4:1 & Currie twin sticks
> > > Warn X8000i w/ dual batteries
> > >
> > > "Tom P." <TPatzlaff@aol.com> wrote in message
> > > news:dd809f71.0312281017.6ee22391@posting.google.c om...
> > > > I have an "88" wrangler with a Dana 35 rear and Dana 30 front. I
> > > > currently have 3.55 gears in both diffs. and would like to put 4.56
> > > > gears in both.
> > > > The literature I can find says that if I have 3.55 or lower gears
in
> > > > the D35, I will be ok. But what I need to know is if the 4.56 gears
> > > > will fit in the D30 case? From what I can find it sounds like I'm
> > > > going to need a housing with 3.73 or lower gears in it for the 4.56
to
> > > > fit.I need to find out the real answer.
> > > > Has anyone out there put 4.56 gears in these size housings?
> > > > Any help or advice would be great.
> > > > Tom
> > >
> > >
> >
> >
>
>
#20
Guest
Posts: n/a
Re: 4.56 gears in a Dana 30 front
I don't think there is any difference - all internal parts are the same.
Did you see Bill's list?
http://www.----------.com/tooth_count.txt
JimG
"Terry Jeffrey" <twjeffrey@hotmail.com> wrote in message
news:zLHHb.22523$Pg1.19236@newsread1.news.pas.eart hlink.net...
> My original gear was 3.07 too, but I'm certain I did not have to replace
the
> D30 carrier in conjunction with using the LockRite. Maybe this is a
> difference in the stock '80 vs '92 D30?
>
> Terry.
>
>
> "JimG" <jimg@cj7_2muchspam.com> wrote in message
> news:FzHHb.32183$iN4.2074@news01.roc.ny...
> > If original gear is higher that 3.73, the carrier has to be replaced.
My
> > original gear was 3.07. I had to replace the carriers in both front and
> > rear.
> >
> > JimG
> >
> > "Terry Jeffrey" <twjeffrey@hotmail.com> wrote in message
> > news:XZFHb.22399$Pg1.9205@newsread1.news.pas.earth link.net...
> > > It's been a few years, but thinking back I'm sure I didn't have to
> replace
> > > the entire reverse-cut D30 carrier when I installed the 4.56 R&P
because
> I
> > > installed a LockRight locker at the same time, which replaces the side
> and
> > > spider gears. Didn't your LockRight install go this way too?
> > >
> > > Terry 92YJ
> > > (now running dual D60s w/Detroits)
> > >
> > >
> > > "JimG" <jimg@cj7_2muchspam.com> wrote in message
> > > news:pdFHb.32159$Wc4.17075@news01.roc.ny...
> > > > You will have to get a new carrier for the D30, been there, done
that.
> > > >
> > > > --
> > > > JimG
> > > > 80' CJ-7 258 CID
> > > > 35" BFG MT on 15x10 Centerlines
> > > > D44 Rear, Dana 30 Front. SOA
> > > > 4.56 Gears, LockRight F&R
> > > > Dana 300 w/4:1 & Currie twin sticks
> > > > Warn X8000i w/ dual batteries
> > > >
> > > > "Tom P." <TPatzlaff@aol.com> wrote in message
> > > > news:dd809f71.0312281017.6ee22391@posting.google.c om...
> > > > > I have an "88" wrangler with a Dana 35 rear and Dana 30 front. I
> > > > > currently have 3.55 gears in both diffs. and would like to put
4.56
> > > > > gears in both.
> > > > > The literature I can find says that if I have 3.55 or lower
gears
> in
> > > > > the D35, I will be ok. But what I need to know is if the 4.56
gears
> > > > > will fit in the D30 case? From what I can find it sounds like I'm
> > > > > going to need a housing with 3.73 or lower gears in it for the
4.56
> to
> > > > > fit.I need to find out the real answer.
> > > > > Has anyone out there put 4.56 gears in these size housings?
> > > > > Any help or advice would be great.
> > > > > Tom
> > > >
> > > >
> > >
> > >
> >
> >
>
>
Did you see Bill's list?
http://www.----------.com/tooth_count.txt
JimG
"Terry Jeffrey" <twjeffrey@hotmail.com> wrote in message
news:zLHHb.22523$Pg1.19236@newsread1.news.pas.eart hlink.net...
> My original gear was 3.07 too, but I'm certain I did not have to replace
the
> D30 carrier in conjunction with using the LockRite. Maybe this is a
> difference in the stock '80 vs '92 D30?
>
> Terry.
>
>
> "JimG" <jimg@cj7_2muchspam.com> wrote in message
> news:FzHHb.32183$iN4.2074@news01.roc.ny...
> > If original gear is higher that 3.73, the carrier has to be replaced.
My
> > original gear was 3.07. I had to replace the carriers in both front and
> > rear.
> >
> > JimG
> >
> > "Terry Jeffrey" <twjeffrey@hotmail.com> wrote in message
> > news:XZFHb.22399$Pg1.9205@newsread1.news.pas.earth link.net...
> > > It's been a few years, but thinking back I'm sure I didn't have to
> replace
> > > the entire reverse-cut D30 carrier when I installed the 4.56 R&P
because
> I
> > > installed a LockRight locker at the same time, which replaces the side
> and
> > > spider gears. Didn't your LockRight install go this way too?
> > >
> > > Terry 92YJ
> > > (now running dual D60s w/Detroits)
> > >
> > >
> > > "JimG" <jimg@cj7_2muchspam.com> wrote in message
> > > news:pdFHb.32159$Wc4.17075@news01.roc.ny...
> > > > You will have to get a new carrier for the D30, been there, done
that.
> > > >
> > > > --
> > > > JimG
> > > > 80' CJ-7 258 CID
> > > > 35" BFG MT on 15x10 Centerlines
> > > > D44 Rear, Dana 30 Front. SOA
> > > > 4.56 Gears, LockRight F&R
> > > > Dana 300 w/4:1 & Currie twin sticks
> > > > Warn X8000i w/ dual batteries
> > > >
> > > > "Tom P." <TPatzlaff@aol.com> wrote in message
> > > > news:dd809f71.0312281017.6ee22391@posting.google.c om...
> > > > > I have an "88" wrangler with a Dana 35 rear and Dana 30 front. I
> > > > > currently have 3.55 gears in both diffs. and would like to put
4.56
> > > > > gears in both.
> > > > > The literature I can find says that if I have 3.55 or lower
gears
> in
> > > > > the D35, I will be ok. But what I need to know is if the 4.56
gears
> > > > > will fit in the D30 case? From what I can find it sounds like I'm
> > > > > going to need a housing with 3.73 or lower gears in it for the
4.56
> to
> > > > > fit.I need to find out the real answer.
> > > > > Has anyone out there put 4.56 gears in these size housings?
> > > > > Any help or advice would be great.
> > > > > Tom
> > > >
> > > >
> > >
> > >
> >
> >
>
>