it might jsut have popped out the fastners in the rods

"jim s via CarKB.com" wrote:

> Symptom: When I try to put my jeep into 4 wheel drive the transfer case
> lever just moves forward and back as if it was not connected to anything.
> What did I (my son) break. My jeep is located at the river (our second home)
> and I need to buy parts to fix the problem. What should I buy and how do I
> solve the problem. I would buy all parts for lever and return those that I do
> not need. Thanks in advance.

 

Tim- You were correct. I dropped down the skid plate that seems to also be
the trans. mount and there was the linkage rod all bent and popped out of its
holder. I put it in a vise to straighten it out and then put it back in the
hole. Works great now. A time saving tip: Before trying to screw in the
larger outside bolts on the skid plate be sure to attach the smaller 4 bolts
that keep the rubber trans mount in place and then you need a floor jack to
raise the skid plate up close enough to get the larger bolts started. Another
tip: Dont let anyone use your jeep that does not know how to properly get it
into 4 wheel drive. I am learning and I thank all that responded to my
problem. Thanks Again!!

tim bur wrote:
>it might jsut have popped out the fastners in the rods
>
>> Symptom: When I try to put my jeep into 4 wheel drive the transfer case
>> lever just moves forward and back as if it was not connected to anything.
>> What did I (my son) break. My jeep is located at the river (our second home)
>> and I need to buy parts to fix the problem. What should I buy and how do I
>> solve the problem. I would buy all parts for lever and return those that I do
>> not need. Thanks in advance.


--
Message posted via CarKB.com
http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200506/1

 

Tim- You were correct. I dropped down the skid plate that seems to also be
the trans. mount and there was the linkage rod all bent and popped out of its
holder. I put it in a vise to straighten it out and then put it back in the
hole. Works great now. A time saving tip: Before trying to screw in the
larger outside bolts on the skid plate be sure to attach the smaller 4 bolts
that keep the rubber trans mount in place and then you need a floor jack to
raise the skid plate up close enough to get the larger bolts started. Another
tip: Dont let anyone use your jeep that does not know how to properly get it
into 4 wheel drive. I am learning and I thank all that responded to my
problem. Thanks Again!!

tim bur wrote:
>it might jsut have popped out the fastners in the rods
>
>> Symptom: When I try to put my jeep into 4 wheel drive the transfer case
>> lever just moves forward and back as if it was not connected to anything.
>> What did I (my son) break. My jeep is located at the river (our second home)
>> and I need to buy parts to fix the problem. What should I buy and how do I
>> solve the problem. I would buy all parts for lever and return those that I do
>> not need. Thanks in advance.


--
Message posted via CarKB.com
http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200506/1

 

Tim- You were correct. I dropped down the skid plate that seems to also be
the trans. mount and there was the linkage rod all bent and popped out of its
holder. I put it in a vise to straighten it out and then put it back in the
hole. Works great now. A time saving tip: Before trying to screw in the
larger outside bolts on the skid plate be sure to attach the smaller 4 bolts
that keep the rubber trans mount in place and then you need a floor jack to
raise the skid plate up close enough to get the larger bolts started. Another
tip: Dont let anyone use your jeep that does not know how to properly get it
into 4 wheel drive. I am learning and I thank all that responded to my
problem. Thanks Again!!

tim bur wrote:
>it might jsut have popped out the fastners in the rods
>
>> Symptom: When I try to put my jeep into 4 wheel drive the transfer case
>> lever just moves forward and back as if it was not connected to anything.
>> What did I (my son) break. My jeep is located at the river (our second home)
>> and I need to buy parts to fix the problem. What should I buy and how do I
>> solve the problem. I would buy all parts for lever and return those that I do
>> not need. Thanks in advance.


--
Message posted via CarKB.com
http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200506/1

 

Tim- You were correct. I dropped down the skid plate that seems to also be
the trans. mount and there was the linkage rod all bent and popped out of its
holder. I put it in a vise to straighten it out and then put it back in the
hole. Works great now. A time saving tip: Before trying to screw in the
larger outside bolts on the skid plate be sure to attach the smaller 4 bolts
that keep the rubber trans mount in place and then you need a floor jack to
raise the skid plate up close enough to get the larger bolts started. Another
tip: Dont let anyone use your jeep that does not know how to properly get it
into 4 wheel drive. I am learning and I thank all that responded to my
problem. Thanks Again!!

tim bur wrote:
>it might jsut have popped out the fastners in the rods
>
>> Symptom: When I try to put my jeep into 4 wheel drive the transfer case
>> lever just moves forward and back as if it was not connected to anything.
>> What did I (my son) break. My jeep is located at the river (our second home)
>> and I need to buy parts to fix the problem. What should I buy and how do I
>> solve the problem. I would buy all parts for lever and return those that I do
>> not need. Thanks in advance.


--
Message posted via CarKB.com
http://www.carkb.com/Uwe/Forums.aspx/jeep-cars/200506/1