1996 Cherokee raise drivers side door hinge
09-30-2006, 12:46 PM
#2
Guest
Posts: n/a
Re: 1996 Cherokee raise drivers side door hinge
I thiink the slide plate on that door is in the door side. That said,
sag such as you describe is usually caused by a worn pin in the hinge.
I replaced mine with a hardened roll pin from a local hardware store.
Real bugger to drive out as the access is a bit tight but if you
remove the pin in the stop bar you can get it open enough to get at
them.
If it just bangs on the latch pin at the rear (where the door latch
grabs) then that pin is adjustable as well - but the alignment problem
is again normally the worn hinge pin.
On Sat, 30 Sep 2006 14:09:24 UTC "Ed" <dorlyed@yahoo.com> wrote:
> The drivers side front door bangs on the connection when closed. I
> tried to raise it by loosening the hinge bolts on the frame side and
> raising the door and then tightening them but no luck. Any advise?
>
--
Will Honea
sag such as you describe is usually caused by a worn pin in the hinge.
I replaced mine with a hardened roll pin from a local hardware store.
Real bugger to drive out as the access is a bit tight but if you
remove the pin in the stop bar you can get it open enough to get at
them.
If it just bangs on the latch pin at the rear (where the door latch
grabs) then that pin is adjustable as well - but the alignment problem
is again normally the worn hinge pin.
On Sat, 30 Sep 2006 14:09:24 UTC "Ed" <dorlyed@yahoo.com> wrote:
> The drivers side front door bangs on the connection when closed. I
> tried to raise it by loosening the hinge bolts on the frame side and
> raising the door and then tightening them but no luck. Any advise?
>
--
Will Honea
09-30-2006, 12:46 PM
#3
Guest
Posts: n/a
Re: 1996 Cherokee raise drivers side door hinge
I thiink the slide plate on that door is in the door side. That said,
sag such as you describe is usually caused by a worn pin in the hinge.
I replaced mine with a hardened roll pin from a local hardware store.
Real bugger to drive out as the access is a bit tight but if you
remove the pin in the stop bar you can get it open enough to get at
them.
If it just bangs on the latch pin at the rear (where the door latch
grabs) then that pin is adjustable as well - but the alignment problem
is again normally the worn hinge pin.
On Sat, 30 Sep 2006 14:09:24 UTC "Ed" <dorlyed@yahoo.com> wrote:
> The drivers side front door bangs on the connection when closed. I
> tried to raise it by loosening the hinge bolts on the frame side and
> raising the door and then tightening them but no luck. Any advise?
>
--
Will Honea
sag such as you describe is usually caused by a worn pin in the hinge.
I replaced mine with a hardened roll pin from a local hardware store.
Real bugger to drive out as the access is a bit tight but if you
remove the pin in the stop bar you can get it open enough to get at
them.
If it just bangs on the latch pin at the rear (where the door latch
grabs) then that pin is adjustable as well - but the alignment problem
is again normally the worn hinge pin.
On Sat, 30 Sep 2006 14:09:24 UTC "Ed" <dorlyed@yahoo.com> wrote:
> The drivers side front door bangs on the connection when closed. I
> tried to raise it by loosening the hinge bolts on the frame side and
> raising the door and then tightening them but no luck. Any advise?
>
--
Will Honea
09-30-2006, 12:46 PM
#4
Guest
Posts: n/a
Re: 1996 Cherokee raise drivers side door hinge
I thiink the slide plate on that door is in the door side. That said,
sag such as you describe is usually caused by a worn pin in the hinge.
I replaced mine with a hardened roll pin from a local hardware store.
Real bugger to drive out as the access is a bit tight but if you
remove the pin in the stop bar you can get it open enough to get at
them.
If it just bangs on the latch pin at the rear (where the door latch
grabs) then that pin is adjustable as well - but the alignment problem
is again normally the worn hinge pin.
On Sat, 30 Sep 2006 14:09:24 UTC "Ed" <dorlyed@yahoo.com> wrote:
> The drivers side front door bangs on the connection when closed. I
> tried to raise it by loosening the hinge bolts on the frame side and
> raising the door and then tightening them but no luck. Any advise?
>
--
Will Honea
sag such as you describe is usually caused by a worn pin in the hinge.
I replaced mine with a hardened roll pin from a local hardware store.
Real bugger to drive out as the access is a bit tight but if you
remove the pin in the stop bar you can get it open enough to get at
them.
If it just bangs on the latch pin at the rear (where the door latch
grabs) then that pin is adjustable as well - but the alignment problem
is again normally the worn hinge pin.
On Sat, 30 Sep 2006 14:09:24 UTC "Ed" <dorlyed@yahoo.com> wrote:
> The drivers side front door bangs on the connection when closed. I
> tried to raise it by loosening the hinge bolts on the frame side and
> raising the door and then tightening them but no luck. Any advise?
>
--
Will Honea
Thread
Thread Starter
Forum
Replies
Last Post
Canehdian73
Jeep & 4x4 Items For Sale
1
03-15-2012 01:22 PM
rjenkins9999@aol.com
Jeep Mailing List
0
04-25-2005 04:39 PM
Mark k Robinson
Jeep Mailing List
0
08-09-2003 01:12 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
