Steering Limit Adjust - '98 TJ?
Guest
Posts: n/a
Steering Limit Adjust - '98 TJ?
How do you adjust the limit for the steering angle on a stock '98 TJ?
I bought this Jeep with what I believe are stock 30" tires and alloy wheels,
but the inside of the right (passenger) side tire rubs on the bottom of the
stabilizer bar link. Actually it hits the head of the T55 torq-head bolt
that fastens the bottom of the stabilizer bar link to the axle housing. It
just barely rubs at full steering lock and has not damaged the tire (yet)
but I want to stop the rubbing for obvious reasons. The left side comes
close but does not interfere. I'm thinking I can limit the steering by half
a degree and will eliminate the problem.
TIA,
-Fred W
---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.525 / Virus Database: 322 - Release Date: 10/9/2003
I bought this Jeep with what I believe are stock 30" tires and alloy wheels,
but the inside of the right (passenger) side tire rubs on the bottom of the
stabilizer bar link. Actually it hits the head of the T55 torq-head bolt
that fastens the bottom of the stabilizer bar link to the axle housing. It
just barely rubs at full steering lock and has not damaged the tire (yet)
but I want to stop the rubbing for obvious reasons. The left side comes
close but does not interfere. I'm thinking I can limit the steering by half
a degree and will eliminate the problem.
TIA,
-Fred W
---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.525 / Virus Database: 322 - Release Date: 10/9/2003
Guest
Posts: n/a
Re: Steering Limit Adjust - '98 TJ?
Fred W. did pass the time by typing:
> How do you adjust the limit for the steering angle on a stock '98 TJ?
>
> I bought this Jeep with what I believe are stock 30" tires and alloy wheels,
> but the inside of the right (passenger) side tire rubs on the bottom of the
> stabilizer bar link. Actually it hits the head of the T55 torq-head bolt
> that fastens the bottom of the stabilizer bar link to the axle housing. It
> just barely rubs at full steering lock and has not damaged the tire (yet)
> but I want to stop the rubbing for obvious reasons. The left side comes
> close but does not interfere. I'm thinking I can limit the steering by half
> a degree and will eliminate the problem.
Add a couple of washers to the steering stops.
http://www.imajeep.com/Steering_Stop...ering_stop.htm
--
DougW
> How do you adjust the limit for the steering angle on a stock '98 TJ?
>
> I bought this Jeep with what I believe are stock 30" tires and alloy wheels,
> but the inside of the right (passenger) side tire rubs on the bottom of the
> stabilizer bar link. Actually it hits the head of the T55 torq-head bolt
> that fastens the bottom of the stabilizer bar link to the axle housing. It
> just barely rubs at full steering lock and has not damaged the tire (yet)
> but I want to stop the rubbing for obvious reasons. The left side comes
> close but does not interfere. I'm thinking I can limit the steering by half
> a degree and will eliminate the problem.
Add a couple of washers to the steering stops.
http://www.imajeep.com/Steering_Stop...ering_stop.htm
--
DougW
Guest
Posts: n/a
Re: Steering Limit Adjust - '98 TJ?
Fred W. did pass the time by typing:
> How do you adjust the limit for the steering angle on a stock '98 TJ?
>
> I bought this Jeep with what I believe are stock 30" tires and alloy wheels,
> but the inside of the right (passenger) side tire rubs on the bottom of the
> stabilizer bar link. Actually it hits the head of the T55 torq-head bolt
> that fastens the bottom of the stabilizer bar link to the axle housing. It
> just barely rubs at full steering lock and has not damaged the tire (yet)
> but I want to stop the rubbing for obvious reasons. The left side comes
> close but does not interfere. I'm thinking I can limit the steering by half
> a degree and will eliminate the problem.
Add a couple of washers to the steering stops.
http://www.imajeep.com/Steering_Stop...ering_stop.htm
--
DougW
> How do you adjust the limit for the steering angle on a stock '98 TJ?
>
> I bought this Jeep with what I believe are stock 30" tires and alloy wheels,
> but the inside of the right (passenger) side tire rubs on the bottom of the
> stabilizer bar link. Actually it hits the head of the T55 torq-head bolt
> that fastens the bottom of the stabilizer bar link to the axle housing. It
> just barely rubs at full steering lock and has not damaged the tire (yet)
> but I want to stop the rubbing for obvious reasons. The left side comes
> close but does not interfere. I'm thinking I can limit the steering by half
> a degree and will eliminate the problem.
Add a couple of washers to the steering stops.
http://www.imajeep.com/Steering_Stop...ering_stop.htm
--
DougW
Guest
Posts: n/a
Re: Steering Limit Adjust - '98 TJ?
Fred W. did pass the time by typing:
> How do you adjust the limit for the steering angle on a stock '98 TJ?
>
> I bought this Jeep with what I believe are stock 30" tires and alloy wheels,
> but the inside of the right (passenger) side tire rubs on the bottom of the
> stabilizer bar link. Actually it hits the head of the T55 torq-head bolt
> that fastens the bottom of the stabilizer bar link to the axle housing. It
> just barely rubs at full steering lock and has not damaged the tire (yet)
> but I want to stop the rubbing for obvious reasons. The left side comes
> close but does not interfere. I'm thinking I can limit the steering by half
> a degree and will eliminate the problem.
Add a couple of washers to the steering stops.
http://www.imajeep.com/Steering_Stop...ering_stop.htm
--
DougW
> How do you adjust the limit for the steering angle on a stock '98 TJ?
>
> I bought this Jeep with what I believe are stock 30" tires and alloy wheels,
> but the inside of the right (passenger) side tire rubs on the bottom of the
> stabilizer bar link. Actually it hits the head of the T55 torq-head bolt
> that fastens the bottom of the stabilizer bar link to the axle housing. It
> just barely rubs at full steering lock and has not damaged the tire (yet)
> but I want to stop the rubbing for obvious reasons. The left side comes
> close but does not interfere. I'm thinking I can limit the steering by half
> a degree and will eliminate the problem.
Add a couple of washers to the steering stops.
http://www.imajeep.com/Steering_Stop...ering_stop.htm
--
DougW
Guest
Posts: n/a
Re: Steering Limit Adjust - '98 TJ?
If you look close on the steering knuckle, you will see a bolt with a
lock nut welded onto it that hits at full steering turn.
You back this out and put one thin washer under it and tighten it back
up. The lock nut is the factory set and is tack welded in place.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"Fred W." wrote:
>
> How do you adjust the limit for the steering angle on a stock '98 TJ?
>
> I bought this Jeep with what I believe are stock 30" tires and alloy wheels,
> but the inside of the right (passenger) side tire rubs on the bottom of the
> stabilizer bar link. Actually it hits the head of the T55 torq-head bolt
> that fastens the bottom of the stabilizer bar link to the axle housing. It
> just barely rubs at full steering lock and has not damaged the tire (yet)
> but I want to stop the rubbing for obvious reasons. The left side comes
> close but does not interfere. I'm thinking I can limit the steering by half
> a degree and will eliminate the problem.
>
> TIA,
> -Fred W
>
> ---
> Outgoing mail is certified Virus Free.
> Checked by AVG anti-virus system (http://www.grisoft.com).
> Version: 6.0.525 / Virus Database: 322 - Release Date: 10/9/2003
lock nut welded onto it that hits at full steering turn.
You back this out and put one thin washer under it and tighten it back
up. The lock nut is the factory set and is tack welded in place.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"Fred W." wrote:
>
> How do you adjust the limit for the steering angle on a stock '98 TJ?
>
> I bought this Jeep with what I believe are stock 30" tires and alloy wheels,
> but the inside of the right (passenger) side tire rubs on the bottom of the
> stabilizer bar link. Actually it hits the head of the T55 torq-head bolt
> that fastens the bottom of the stabilizer bar link to the axle housing. It
> just barely rubs at full steering lock and has not damaged the tire (yet)
> but I want to stop the rubbing for obvious reasons. The left side comes
> close but does not interfere. I'm thinking I can limit the steering by half
> a degree and will eliminate the problem.
>
> TIA,
> -Fred W
>
> ---
> Outgoing mail is certified Virus Free.
> Checked by AVG anti-virus system (http://www.grisoft.com).
> Version: 6.0.525 / Virus Database: 322 - Release Date: 10/9/2003
Guest
Posts: n/a
Re: Steering Limit Adjust - '98 TJ?
If you look close on the steering knuckle, you will see a bolt with a
lock nut welded onto it that hits at full steering turn.
You back this out and put one thin washer under it and tighten it back
up. The lock nut is the factory set and is tack welded in place.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"Fred W." wrote:
>
> How do you adjust the limit for the steering angle on a stock '98 TJ?
>
> I bought this Jeep with what I believe are stock 30" tires and alloy wheels,
> but the inside of the right (passenger) side tire rubs on the bottom of the
> stabilizer bar link. Actually it hits the head of the T55 torq-head bolt
> that fastens the bottom of the stabilizer bar link to the axle housing. It
> just barely rubs at full steering lock and has not damaged the tire (yet)
> but I want to stop the rubbing for obvious reasons. The left side comes
> close but does not interfere. I'm thinking I can limit the steering by half
> a degree and will eliminate the problem.
>
> TIA,
> -Fred W
>
> ---
> Outgoing mail is certified Virus Free.
> Checked by AVG anti-virus system (http://www.grisoft.com).
> Version: 6.0.525 / Virus Database: 322 - Release Date: 10/9/2003
lock nut welded onto it that hits at full steering turn.
You back this out and put one thin washer under it and tighten it back
up. The lock nut is the factory set and is tack welded in place.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"Fred W." wrote:
>
> How do you adjust the limit for the steering angle on a stock '98 TJ?
>
> I bought this Jeep with what I believe are stock 30" tires and alloy wheels,
> but the inside of the right (passenger) side tire rubs on the bottom of the
> stabilizer bar link. Actually it hits the head of the T55 torq-head bolt
> that fastens the bottom of the stabilizer bar link to the axle housing. It
> just barely rubs at full steering lock and has not damaged the tire (yet)
> but I want to stop the rubbing for obvious reasons. The left side comes
> close but does not interfere. I'm thinking I can limit the steering by half
> a degree and will eliminate the problem.
>
> TIA,
> -Fred W
>
> ---
> Outgoing mail is certified Virus Free.
> Checked by AVG anti-virus system (http://www.grisoft.com).
> Version: 6.0.525 / Virus Database: 322 - Release Date: 10/9/2003
Guest
Posts: n/a
Re: Steering Limit Adjust - '98 TJ?
If you look close on the steering knuckle, you will see a bolt with a
lock nut welded onto it that hits at full steering turn.
You back this out and put one thin washer under it and tighten it back
up. The lock nut is the factory set and is tack welded in place.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"Fred W." wrote:
>
> How do you adjust the limit for the steering angle on a stock '98 TJ?
>
> I bought this Jeep with what I believe are stock 30" tires and alloy wheels,
> but the inside of the right (passenger) side tire rubs on the bottom of the
> stabilizer bar link. Actually it hits the head of the T55 torq-head bolt
> that fastens the bottom of the stabilizer bar link to the axle housing. It
> just barely rubs at full steering lock and has not damaged the tire (yet)
> but I want to stop the rubbing for obvious reasons. The left side comes
> close but does not interfere. I'm thinking I can limit the steering by half
> a degree and will eliminate the problem.
>
> TIA,
> -Fred W
>
> ---
> Outgoing mail is certified Virus Free.
> Checked by AVG anti-virus system (http://www.grisoft.com).
> Version: 6.0.525 / Virus Database: 322 - Release Date: 10/9/2003
lock nut welded onto it that hits at full steering turn.
You back this out and put one thin washer under it and tighten it back
up. The lock nut is the factory set and is tack welded in place.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
"Fred W." wrote:
>
> How do you adjust the limit for the steering angle on a stock '98 TJ?
>
> I bought this Jeep with what I believe are stock 30" tires and alloy wheels,
> but the inside of the right (passenger) side tire rubs on the bottom of the
> stabilizer bar link. Actually it hits the head of the T55 torq-head bolt
> that fastens the bottom of the stabilizer bar link to the axle housing. It
> just barely rubs at full steering lock and has not damaged the tire (yet)
> but I want to stop the rubbing for obvious reasons. The left side comes
> close but does not interfere. I'm thinking I can limit the steering by half
> a degree and will eliminate the problem.
>
> TIA,
> -Fred W
>
> ---
> Outgoing mail is certified Virus Free.
> Checked by AVG anti-virus system (http://www.grisoft.com).
> Version: 6.0.525 / Virus Database: 322 - Release Date: 10/9/2003
Guest
Posts: n/a
Re: Steering Limit Adjust - '98 TJ?
Try just one washer on the steering stop on the opposite side of the rubbing
tire. If it's just barely rubbing, one 1/2 inch flat washer should be
sufficient.
--
Jim
--
98 TJ SE
90 SJ GW
http://www.delawareja.com/gallery/JDJeep98
"You can do any job in the world with the wrong tool if you try hard
enough..."
"4x4" in caps is "$X$"
"DougW" <post.replies@invalid.address> wrote in message
news:FVQmb.30507$iq3.8392@okepread01...
> Fred W. did pass the time by typing:
> > How do you adjust the limit for the steering angle on a stock '98 TJ?
> >
> > I bought this Jeep with what I believe are stock 30" tires and alloy
wheels,
> > but the inside of the right (passenger) side tire rubs on the bottom of
the
> > stabilizer bar link. Actually it hits the head of the T55 torq-head
bolt
> > that fastens the bottom of the stabilizer bar link to the axle housing.
It
> > just barely rubs at full steering lock and has not damaged the tire
(yet)
> > but I want to stop the rubbing for obvious reasons. The left side comes
> > close but does not interfere. I'm thinking I can limit the steering by
half
> > a degree and will eliminate the problem.
>
> Add a couple of washers to the steering stops.
> http://www.imajeep.com/Steering_Stop...ering_stop.htm
>
> --
> DougW
>
>
tire. If it's just barely rubbing, one 1/2 inch flat washer should be
sufficient.
--
Jim
--
98 TJ SE
90 SJ GW
http://www.delawareja.com/gallery/JDJeep98
"You can do any job in the world with the wrong tool if you try hard
enough..."
"4x4" in caps is "$X$"
"DougW" <post.replies@invalid.address> wrote in message
news:FVQmb.30507$iq3.8392@okepread01...
> Fred W. did pass the time by typing:
> > How do you adjust the limit for the steering angle on a stock '98 TJ?
> >
> > I bought this Jeep with what I believe are stock 30" tires and alloy
wheels,
> > but the inside of the right (passenger) side tire rubs on the bottom of
the
> > stabilizer bar link. Actually it hits the head of the T55 torq-head
bolt
> > that fastens the bottom of the stabilizer bar link to the axle housing.
It
> > just barely rubs at full steering lock and has not damaged the tire
(yet)
> > but I want to stop the rubbing for obvious reasons. The left side comes
> > close but does not interfere. I'm thinking I can limit the steering by
half
> > a degree and will eliminate the problem.
>
> Add a couple of washers to the steering stops.
> http://www.imajeep.com/Steering_Stop...ering_stop.htm
>
> --
> DougW
>
>
Guest
Posts: n/a
Re: Steering Limit Adjust - '98 TJ?
Try just one washer on the steering stop on the opposite side of the rubbing
tire. If it's just barely rubbing, one 1/2 inch flat washer should be
sufficient.
--
Jim
--
98 TJ SE
90 SJ GW
http://www.delawareja.com/gallery/JDJeep98
"You can do any job in the world with the wrong tool if you try hard
enough..."
"4x4" in caps is "$X$"
"DougW" <post.replies@invalid.address> wrote in message
news:FVQmb.30507$iq3.8392@okepread01...
> Fred W. did pass the time by typing:
> > How do you adjust the limit for the steering angle on a stock '98 TJ?
> >
> > I bought this Jeep with what I believe are stock 30" tires and alloy
wheels,
> > but the inside of the right (passenger) side tire rubs on the bottom of
the
> > stabilizer bar link. Actually it hits the head of the T55 torq-head
bolt
> > that fastens the bottom of the stabilizer bar link to the axle housing.
It
> > just barely rubs at full steering lock and has not damaged the tire
(yet)
> > but I want to stop the rubbing for obvious reasons. The left side comes
> > close but does not interfere. I'm thinking I can limit the steering by
half
> > a degree and will eliminate the problem.
>
> Add a couple of washers to the steering stops.
> http://www.imajeep.com/Steering_Stop...ering_stop.htm
>
> --
> DougW
>
>
tire. If it's just barely rubbing, one 1/2 inch flat washer should be
sufficient.
--
Jim
--
98 TJ SE
90 SJ GW
http://www.delawareja.com/gallery/JDJeep98
"You can do any job in the world with the wrong tool if you try hard
enough..."
"4x4" in caps is "$X$"
"DougW" <post.replies@invalid.address> wrote in message
news:FVQmb.30507$iq3.8392@okepread01...
> Fred W. did pass the time by typing:
> > How do you adjust the limit for the steering angle on a stock '98 TJ?
> >
> > I bought this Jeep with what I believe are stock 30" tires and alloy
wheels,
> > but the inside of the right (passenger) side tire rubs on the bottom of
the
> > stabilizer bar link. Actually it hits the head of the T55 torq-head
bolt
> > that fastens the bottom of the stabilizer bar link to the axle housing.
It
> > just barely rubs at full steering lock and has not damaged the tire
(yet)
> > but I want to stop the rubbing for obvious reasons. The left side comes
> > close but does not interfere. I'm thinking I can limit the steering by
half
> > a degree and will eliminate the problem.
>
> Add a couple of washers to the steering stops.
> http://www.imajeep.com/Steering_Stop...ering_stop.htm
>
> --
> DougW
>
>
Guest
Posts: n/a
Re: Steering Limit Adjust - '98 TJ?
Try just one washer on the steering stop on the opposite side of the rubbing
tire. If it's just barely rubbing, one 1/2 inch flat washer should be
sufficient.
--
Jim
--
98 TJ SE
90 SJ GW
http://www.delawareja.com/gallery/JDJeep98
"You can do any job in the world with the wrong tool if you try hard
enough..."
"4x4" in caps is "$X$"
"DougW" <post.replies@invalid.address> wrote in message
news:FVQmb.30507$iq3.8392@okepread01...
> Fred W. did pass the time by typing:
> > How do you adjust the limit for the steering angle on a stock '98 TJ?
> >
> > I bought this Jeep with what I believe are stock 30" tires and alloy
wheels,
> > but the inside of the right (passenger) side tire rubs on the bottom of
the
> > stabilizer bar link. Actually it hits the head of the T55 torq-head
bolt
> > that fastens the bottom of the stabilizer bar link to the axle housing.
It
> > just barely rubs at full steering lock and has not damaged the tire
(yet)
> > but I want to stop the rubbing for obvious reasons. The left side comes
> > close but does not interfere. I'm thinking I can limit the steering by
half
> > a degree and will eliminate the problem.
>
> Add a couple of washers to the steering stops.
> http://www.imajeep.com/Steering_Stop...ering_stop.htm
>
> --
> DougW
>
>
tire. If it's just barely rubbing, one 1/2 inch flat washer should be
sufficient.
--
Jim
--
98 TJ SE
90 SJ GW
http://www.delawareja.com/gallery/JDJeep98
"You can do any job in the world with the wrong tool if you try hard
enough..."
"4x4" in caps is "$X$"
"DougW" <post.replies@invalid.address> wrote in message
news:FVQmb.30507$iq3.8392@okepread01...
> Fred W. did pass the time by typing:
> > How do you adjust the limit for the steering angle on a stock '98 TJ?
> >
> > I bought this Jeep with what I believe are stock 30" tires and alloy
wheels,
> > but the inside of the right (passenger) side tire rubs on the bottom of
the
> > stabilizer bar link. Actually it hits the head of the T55 torq-head
bolt
> > that fastens the bottom of the stabilizer bar link to the axle housing.
It
> > just barely rubs at full steering lock and has not damaged the tire
(yet)
> > but I want to stop the rubbing for obvious reasons. The left side comes
> > close but does not interfere. I'm thinking I can limit the steering by
half
> > a degree and will eliminate the problem.
>
> Add a couple of washers to the steering stops.
> http://www.imajeep.com/Steering_Stop...ering_stop.htm
>
> --
> DougW
>
>