1990 wrangler 4 wheel drive vacuum line?
Guest
Posts: n/a
1990 wrangler 4 wheel drive vacuum line?
I have a 1990 Jeep Wrangler who's vacuum lines have been disconnected.
I need help sorting them out as to what goes where. I think I have most
of them connected properly but my 4 wheel drive light is on, but when
you ramp up the rpms it goes out. I just need some help getting the
lines in their proper places so the Wrangler idles rather than
stalling.
Thanks for the help
Jeremy
I need help sorting them out as to what goes where. I think I have most
of them connected properly but my 4 wheel drive light is on, but when
you ramp up the rpms it goes out. I just need some help getting the
lines in their proper places so the Wrangler idles rather than
stalling.
Thanks for the help
Jeremy
Guest
Posts: n/a
Re: 1990 wrangler 4 wheel drive vacuum line?
To fix the stalling, there is a black plastic line that goes from the
driver's side of the engine down to the vac switch on the driver's side
of the transfer case. Find the line and plug it, that should get your
engine running correctly. If not, keep working on the vac lines.
To check out the vac operated axle disconnect, hook up the vac line to
the transfer case switch. With the engine running, CAREFULLY pull the
connector to the front axle off the vac motor. The green line should
have a slight vac with the transfer case in 2wd, the yellow line should
have vac in 4wd. If it doesn't switch back and forth, replace the vac
switch on the transfer case, $25 from the dealer. If no vac on either,
you have a bad vac line somewhere.
Your symptoms sound like a cracked vac line or trashed rubber connector
for the line to the switch or vac motor. Pretty common for that vintage
Jeep.
Jeremy wrote:
> I have a 1990 Jeep Wrangler who's vacuum lines have been disconnected.
> I need help sorting them out as to what goes where. I think I have most
> of them connected properly but my 4 wheel drive light is on, but when
> you ramp up the rpms it goes out. I just need some help getting the
> lines in their proper places so the Wrangler idles rather than
> stalling.
>
> Thanks for the help
> Jeremy
>
driver's side of the engine down to the vac switch on the driver's side
of the transfer case. Find the line and plug it, that should get your
engine running correctly. If not, keep working on the vac lines.
To check out the vac operated axle disconnect, hook up the vac line to
the transfer case switch. With the engine running, CAREFULLY pull the
connector to the front axle off the vac motor. The green line should
have a slight vac with the transfer case in 2wd, the yellow line should
have vac in 4wd. If it doesn't switch back and forth, replace the vac
switch on the transfer case, $25 from the dealer. If no vac on either,
you have a bad vac line somewhere.
Your symptoms sound like a cracked vac line or trashed rubber connector
for the line to the switch or vac motor. Pretty common for that vintage
Jeep.
Jeremy wrote:
> I have a 1990 Jeep Wrangler who's vacuum lines have been disconnected.
> I need help sorting them out as to what goes where. I think I have most
> of them connected properly but my 4 wheel drive light is on, but when
> you ramp up the rpms it goes out. I just need some help getting the
> lines in their proper places so the Wrangler idles rather than
> stalling.
>
> Thanks for the help
> Jeremy
>
Guest
Posts: n/a
Re: 1990 wrangler 4 wheel drive vacuum line?
To fix the stalling, there is a black plastic line that goes from the
driver's side of the engine down to the vac switch on the driver's side
of the transfer case. Find the line and plug it, that should get your
engine running correctly. If not, keep working on the vac lines.
To check out the vac operated axle disconnect, hook up the vac line to
the transfer case switch. With the engine running, CAREFULLY pull the
connector to the front axle off the vac motor. The green line should
have a slight vac with the transfer case in 2wd, the yellow line should
have vac in 4wd. If it doesn't switch back and forth, replace the vac
switch on the transfer case, $25 from the dealer. If no vac on either,
you have a bad vac line somewhere.
Your symptoms sound like a cracked vac line or trashed rubber connector
for the line to the switch or vac motor. Pretty common for that vintage
Jeep.
Jeremy wrote:
> I have a 1990 Jeep Wrangler who's vacuum lines have been disconnected.
> I need help sorting them out as to what goes where. I think I have most
> of them connected properly but my 4 wheel drive light is on, but when
> you ramp up the rpms it goes out. I just need some help getting the
> lines in their proper places so the Wrangler idles rather than
> stalling.
>
> Thanks for the help
> Jeremy
>
driver's side of the engine down to the vac switch on the driver's side
of the transfer case. Find the line and plug it, that should get your
engine running correctly. If not, keep working on the vac lines.
To check out the vac operated axle disconnect, hook up the vac line to
the transfer case switch. With the engine running, CAREFULLY pull the
connector to the front axle off the vac motor. The green line should
have a slight vac with the transfer case in 2wd, the yellow line should
have vac in 4wd. If it doesn't switch back and forth, replace the vac
switch on the transfer case, $25 from the dealer. If no vac on either,
you have a bad vac line somewhere.
Your symptoms sound like a cracked vac line or trashed rubber connector
for the line to the switch or vac motor. Pretty common for that vintage
Jeep.
Jeremy wrote:
> I have a 1990 Jeep Wrangler who's vacuum lines have been disconnected.
> I need help sorting them out as to what goes where. I think I have most
> of them connected properly but my 4 wheel drive light is on, but when
> you ramp up the rpms it goes out. I just need some help getting the
> lines in their proper places so the Wrangler idles rather than
> stalling.
>
> Thanks for the help
> Jeremy
>
Guest
Posts: n/a
Re: 1990 wrangler 4 wheel drive vacuum line?
To fix the stalling, there is a black plastic line that goes from the
driver's side of the engine down to the vac switch on the driver's side
of the transfer case. Find the line and plug it, that should get your
engine running correctly. If not, keep working on the vac lines.
To check out the vac operated axle disconnect, hook up the vac line to
the transfer case switch. With the engine running, CAREFULLY pull the
connector to the front axle off the vac motor. The green line should
have a slight vac with the transfer case in 2wd, the yellow line should
have vac in 4wd. If it doesn't switch back and forth, replace the vac
switch on the transfer case, $25 from the dealer. If no vac on either,
you have a bad vac line somewhere.
Your symptoms sound like a cracked vac line or trashed rubber connector
for the line to the switch or vac motor. Pretty common for that vintage
Jeep.
Jeremy wrote:
> I have a 1990 Jeep Wrangler who's vacuum lines have been disconnected.
> I need help sorting them out as to what goes where. I think I have most
> of them connected properly but my 4 wheel drive light is on, but when
> you ramp up the rpms it goes out. I just need some help getting the
> lines in their proper places so the Wrangler idles rather than
> stalling.
>
> Thanks for the help
> Jeremy
>
driver's side of the engine down to the vac switch on the driver's side
of the transfer case. Find the line and plug it, that should get your
engine running correctly. If not, keep working on the vac lines.
To check out the vac operated axle disconnect, hook up the vac line to
the transfer case switch. With the engine running, CAREFULLY pull the
connector to the front axle off the vac motor. The green line should
have a slight vac with the transfer case in 2wd, the yellow line should
have vac in 4wd. If it doesn't switch back and forth, replace the vac
switch on the transfer case, $25 from the dealer. If no vac on either,
you have a bad vac line somewhere.
Your symptoms sound like a cracked vac line or trashed rubber connector
for the line to the switch or vac motor. Pretty common for that vintage
Jeep.
Jeremy wrote:
> I have a 1990 Jeep Wrangler who's vacuum lines have been disconnected.
> I need help sorting them out as to what goes where. I think I have most
> of them connected properly but my 4 wheel drive light is on, but when
> you ramp up the rpms it goes out. I just need some help getting the
> lines in their proper places so the Wrangler idles rather than
> stalling.
>
> Thanks for the help
> Jeremy
>
Guest
Posts: n/a
Re: 1990 wrangler 4 wheel drive vacuum line?
What engine?
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
Jeremy wrote:
>
> I have a 1990 Jeep Wrangler who's vacuum lines have been disconnected.
> I need help sorting them out as to what goes where. I think I have most
> of them connected properly but my 4 wheel drive light is on, but when
> you ramp up the rpms it goes out. I just need some help getting the
> lines in their proper places so the Wrangler idles rather than
> stalling.
>
> Thanks for the help
> Jeremy
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
Jeremy wrote:
>
> I have a 1990 Jeep Wrangler who's vacuum lines have been disconnected.
> I need help sorting them out as to what goes where. I think I have most
> of them connected properly but my 4 wheel drive light is on, but when
> you ramp up the rpms it goes out. I just need some help getting the
> lines in their proper places so the Wrangler idles rather than
> stalling.
>
> Thanks for the help
> Jeremy
Guest
Posts: n/a
Re: 1990 wrangler 4 wheel drive vacuum line?
What engine?
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
Jeremy wrote:
>
> I have a 1990 Jeep Wrangler who's vacuum lines have been disconnected.
> I need help sorting them out as to what goes where. I think I have most
> of them connected properly but my 4 wheel drive light is on, but when
> you ramp up the rpms it goes out. I just need some help getting the
> lines in their proper places so the Wrangler idles rather than
> stalling.
>
> Thanks for the help
> Jeremy
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
Jeremy wrote:
>
> I have a 1990 Jeep Wrangler who's vacuum lines have been disconnected.
> I need help sorting them out as to what goes where. I think I have most
> of them connected properly but my 4 wheel drive light is on, but when
> you ramp up the rpms it goes out. I just need some help getting the
> lines in their proper places so the Wrangler idles rather than
> stalling.
>
> Thanks for the help
> Jeremy
Guest
Posts: n/a
Re: 1990 wrangler 4 wheel drive vacuum line?
What engine?
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
Jeremy wrote:
>
> I have a 1990 Jeep Wrangler who's vacuum lines have been disconnected.
> I need help sorting them out as to what goes where. I think I have most
> of them connected properly but my 4 wheel drive light is on, but when
> you ramp up the rpms it goes out. I just need some help getting the
> lines in their proper places so the Wrangler idles rather than
> stalling.
>
> Thanks for the help
> Jeremy
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
Jeremy wrote:
>
> I have a 1990 Jeep Wrangler who's vacuum lines have been disconnected.
> I need help sorting them out as to what goes where. I think I have most
> of them connected properly but my 4 wheel drive light is on, but when
> you ramp up the rpms it goes out. I just need some help getting the
> lines in their proper places so the Wrangler idles rather than
> stalling.
>
> Thanks for the help
> Jeremy
Guest
Posts: n/a
Re: 1990 wrangler 4 wheel drive vacuum line?
"Jeremy" <JeremyAC@gmail.com> wrote in message
news:1157939708.790066.150040@d34g2000cwd.googlegr oups.com...
> I have a 1990 Jeep Wrangler who's vacuum lines have been disconnected.
> I need help sorting them out as to what goes where. I think I have most
> of them connected properly but my 4 wheel drive light is on, but when
> you ramp up the rpms it goes out. I just need some help getting the
> lines in their proper places so the Wrangler idles rather than
> stalling.
>
> Thanks for the help
> Jeremy
>
I've got an 87 YJ with a 258 that I did that to once. If I recall, I
accidentally switched 2 vacuum lines 'somewhere near the distributor cap'.
Sorry I don't recall clearer.
news:1157939708.790066.150040@d34g2000cwd.googlegr oups.com...
> I have a 1990 Jeep Wrangler who's vacuum lines have been disconnected.
> I need help sorting them out as to what goes where. I think I have most
> of them connected properly but my 4 wheel drive light is on, but when
> you ramp up the rpms it goes out. I just need some help getting the
> lines in their proper places so the Wrangler idles rather than
> stalling.
>
> Thanks for the help
> Jeremy
>
I've got an 87 YJ with a 258 that I did that to once. If I recall, I
accidentally switched 2 vacuum lines 'somewhere near the distributor cap'.
Sorry I don't recall clearer.
Guest
Posts: n/a
Re: 1990 wrangler 4 wheel drive vacuum line?
"Jeremy" <JeremyAC@gmail.com> wrote in message
news:1157939708.790066.150040@d34g2000cwd.googlegr oups.com...
> I have a 1990 Jeep Wrangler who's vacuum lines have been disconnected.
> I need help sorting them out as to what goes where. I think I have most
> of them connected properly but my 4 wheel drive light is on, but when
> you ramp up the rpms it goes out. I just need some help getting the
> lines in their proper places so the Wrangler idles rather than
> stalling.
>
> Thanks for the help
> Jeremy
>
I've got an 87 YJ with a 258 that I did that to once. If I recall, I
accidentally switched 2 vacuum lines 'somewhere near the distributor cap'.
Sorry I don't recall clearer.
news:1157939708.790066.150040@d34g2000cwd.googlegr oups.com...
> I have a 1990 Jeep Wrangler who's vacuum lines have been disconnected.
> I need help sorting them out as to what goes where. I think I have most
> of them connected properly but my 4 wheel drive light is on, but when
> you ramp up the rpms it goes out. I just need some help getting the
> lines in their proper places so the Wrangler idles rather than
> stalling.
>
> Thanks for the help
> Jeremy
>
I've got an 87 YJ with a 258 that I did that to once. If I recall, I
accidentally switched 2 vacuum lines 'somewhere near the distributor cap'.
Sorry I don't recall clearer.
Guest
Posts: n/a
Re: 1990 wrangler 4 wheel drive vacuum line?
"Jeremy" <JeremyAC@gmail.com> wrote in message
news:1157939708.790066.150040@d34g2000cwd.googlegr oups.com...
> I have a 1990 Jeep Wrangler who's vacuum lines have been disconnected.
> I need help sorting them out as to what goes where. I think I have most
> of them connected properly but my 4 wheel drive light is on, but when
> you ramp up the rpms it goes out. I just need some help getting the
> lines in their proper places so the Wrangler idles rather than
> stalling.
>
> Thanks for the help
> Jeremy
>
I've got an 87 YJ with a 258 that I did that to once. If I recall, I
accidentally switched 2 vacuum lines 'somewhere near the distributor cap'.
Sorry I don't recall clearer.
news:1157939708.790066.150040@d34g2000cwd.googlegr oups.com...
> I have a 1990 Jeep Wrangler who's vacuum lines have been disconnected.
> I need help sorting them out as to what goes where. I think I have most
> of them connected properly but my 4 wheel drive light is on, but when
> you ramp up the rpms it goes out. I just need some help getting the
> lines in their proper places so the Wrangler idles rather than
> stalling.
>
> Thanks for the help
> Jeremy
>
I've got an 87 YJ with a 258 that I did that to once. If I recall, I
accidentally switched 2 vacuum lines 'somewhere near the distributor cap'.
Sorry I don't recall clearer.