"No Fuse" - No interior dome lights & Radio/CD player, Trip odometer reset to zero
Long story short, my Jeep just got replaced a new battery & starter. When I got the Jeep from the mehanic, I found the "No Fuse" message appeared on the odometer. As I mentioned on the subject line, my problem are as follows:
- Interior dome/reading lights not work(the dash lights, head- and tail-lights still work) - Radio/CD player not work - The trip odometer memory (which would reset each time the car was shut down) I did my research of this issue for a week (included other Jeep's forums) but all the answers are saying it's IOD fuse problem!! Bought new IOD fuse (50A - red color) last night & tried but no luck!!! Please let me know what else I can do now before bringing my Jeep back to mechanic again!?? Any help or suggestions would be appreciated. Note: My Jeep is 2001 TJ Sahara 5 speed model. Thanks in advance. |
Re: "No Fuse" - No interior dome lights & Radio/CD player, Trip odometer reset to zer
Did you get this issue fixed or do you still need help?
|
Re: "No Fuse" - No interior dome lights & Radio/CD player, Trip odometer reset to zer
Originally Posted by RiponredTJ
(Post 557379)
Did you get this issue fixed or do you still need help?
|
Re: "No Fuse" - No interior dome lights & Radio/CD player, Trip odometer reset to zer
Symptom:
*(NO FUSE( IN VF DISPLAY POSSIBLE CAUSES FUSED B(+) CIRCUIT SHORT TO GROUND FUSED B(+) CIRCUIT OPEN INSTRUMENT CLUSTER TEST ACTION APPLICABILITY 1 Turn the ignition off. Inspect the #24 fuse in the Power Distribution Center. If the fuse is open, replace with proper rated fuse. Turn the ignition on for one minute. Turn the ignition off. Inspect the #24 fuse in the Power Distribution Center. Is the fuse open? All Yes ! Repair the Fused B(+) circuit for a short to ground. Perform BODY VERIFICATION TEST - VER 1. No ! Go To 2 2 Turn the ignition off. Disconnect the Instrument Cluster C1 harness connector. Check connectors - Clean/repair as necessary. Measure the voltage between the Fused B(+) circuit and ground. Is the voltage above 10.5 volts? All Yes ! Replace and configure the Instrument Cluster in accordance with the Service Information. Perform BODY VERIFICATION TEST - VER 1. No ! Repair the Fused B(+) circuit for an open. Perform BODY VERIFICATION TEST - VER 1. Check fuse 24 in the Power Distribution Center You should have 12v on pin 12 of Instrument Cluster connector C1 if not and the fuse is good you may have an open connection someplace. |
Re: "No Fuse" - No interior dome lights & Radio/CD player, Trip odometer reset to zer
Originally Posted by shutt40
(Post 557402)
Symptom:
*(NO FUSE( IN VF DISPLAY POSSIBLE CAUSES FUSED B(+) CIRCUIT SHORT TO GROUND FUSED B(+) CIRCUIT OPEN INSTRUMENT CLUSTER TEST ACTION APPLICABILITY 1 Turn the ignition off. Inspect the #24 fuse in the Power Distribution Center. If the fuse is open, replace with proper rated fuse. Turn the ignition on for one minute. Turn the ignition off. Inspect the #24 fuse in the Power Distribution Center. Is the fuse open? All Yes ! Repair the Fused B(+) circuit for a short to ground. Perform BODY VERIFICATION TEST - VER 1. No ! Go To 2 2 Turn the ignition off. Disconnect the Instrument Cluster C1 harness connector. Check connectors - Clean/repair as necessary. Measure the voltage between the Fused B(+) circuit and ground. Is the voltage above 10.5 volts? All Yes ! Replace and configure the Instrument Cluster in accordance with the Service Information. Perform BODY VERIFICATION TEST - VER 1. No ! Repair the Fused B(+) circuit for an open. Perform BODY VERIFICATION TEST - VER 1. Check fuse 24 in the Power Distribution Center You should have 12v on pin 12 of Instrument Cluster connector C1 if not and the fuse is good you may have an open connection someplace. I will give it another try in the weekend. |
All times are GMT -4. The time now is 09:10 PM. |
© 2024 MH Sub I, LLC dba Internet Brands