valve stem has lip/rim can't get seal on
 

83 CJ7 4.2L

I'm on #1 cylinder and I have a valve that has a rim or lip at the top of
the stem where I can get the seal only partially down. I can't get past
where the keepers sit and down onto the stem. What's up with this? What
can I do in this situation? The last three valves have been ok. This is
the first with the problem.

Thanks for any suggestions.

Bill

Re: valve stem has lip/rim can't get seal on
 

Should I protect the area from filings and take a file and file the lip off?

Thanks,

Bill

"William Oliveri" <wuji@bigvalley.net> wrote in message
news:bvf197$ro51k$1@ID-193866.news.uni-berlin.de...
> 83 CJ7 4.2L
>
> I'm on #1 cylinder and I have a valve that has a rim or lip at the top of
> the stem where I can get the seal only partially down. I can't get past
> where the keepers sit and down onto the stem. What's up with this? What
> can I do in this situation? The last three valves have been ok. This is
> the first with the problem.
>
> Thanks for any suggestions.
>
> Bill
>
>

Re: valve stem has lip/rim can't get seal on
 

Should I protect the area from filings and take a file and file the lip off?

Thanks,

Bill

"William Oliveri" <wuji@bigvalley.net> wrote in message
news:bvf197$ro51k$1@ID-193866.news.uni-berlin.de...
> 83 CJ7 4.2L
>
> I'm on #1 cylinder and I have a valve that has a rim or lip at the top of
> the stem where I can get the seal only partially down. I can't get past
> where the keepers sit and down onto the stem. What's up with this? What
> can I do in this situation? The last three valves have been ok. This is
> the first with the problem.
>
> Thanks for any suggestions.
>
> Bill
>
>

Re: valve stem has lip/rim can't get seal on
 

Should I protect the area from filings and take a file and file the lip off?

Thanks,

Bill

"William Oliveri" <wuji@bigvalley.net> wrote in message
news:bvf197$ro51k$1@ID-193866.news.uni-berlin.de...
> 83 CJ7 4.2L
>
> I'm on #1 cylinder and I have a valve that has a rim or lip at the top of
> the stem where I can get the seal only partially down. I can't get past
> where the keepers sit and down onto the stem. What's up with this? What
> can I do in this situation? The last three valves have been ok. This is
> the first with the problem.
>
> Thanks for any suggestions.
>
> Bill
>
>

Re: valve stem has lip/rim can't get seal on
 

Yes.


Jerry


"William Oliveri" <wuji@bigvalley.net> wrote in message
news:bvf37h$r4pdv$1@ID-193866.news.uni-berlin.de...
> Should I protect the area from filings and take a file and file the lip
off?
>
> Thanks,
>
> Bill
>
> "William Oliveri" <wuji@bigvalley.net> wrote in message
> news:bvf197$ro51k$1@ID-193866.news.uni-berlin.de...
> > 83 CJ7 4.2L
> >
> > I'm on #1 cylinder and I have a valve that has a rim or lip at the top
of
> > the stem where I can get the seal only partially down. I can't get past
> > where the keepers sit and down onto the stem. What's up with this?
What
> > can I do in this situation? The last three valves have been ok. This
is
> > the first with the problem.
> >
> > Thanks for any suggestions.
> >
> > Bill
> >
> >
>
>

Re: valve stem has lip/rim can't get seal on
 

Yes.


Jerry


"William Oliveri" <wuji@bigvalley.net> wrote in message
news:bvf37h$r4pdv$1@ID-193866.news.uni-berlin.de...
> Should I protect the area from filings and take a file and file the lip
off?
>
> Thanks,
>
> Bill
>
> "William Oliveri" <wuji@bigvalley.net> wrote in message
> news:bvf197$ro51k$1@ID-193866.news.uni-berlin.de...
> > 83 CJ7 4.2L
> >
> > I'm on #1 cylinder and I have a valve that has a rim or lip at the top
of
> > the stem where I can get the seal only partially down. I can't get past
> > where the keepers sit and down onto the stem. What's up with this?
What
> > can I do in this situation? The last three valves have been ok. This
is
> > the first with the problem.
> >
> > Thanks for any suggestions.
> >
> > Bill
> >
> >
>
>

Re: valve stem has lip/rim can't get seal on
 

Yes.


Jerry


"William Oliveri" <wuji@bigvalley.net> wrote in message
news:bvf37h$r4pdv$1@ID-193866.news.uni-berlin.de...
> Should I protect the area from filings and take a file and file the lip
off?
>
> Thanks,
>
> Bill
>
> "William Oliveri" <wuji@bigvalley.net> wrote in message
> news:bvf197$ro51k$1@ID-193866.news.uni-berlin.de...
> > 83 CJ7 4.2L
> >
> > I'm on #1 cylinder and I have a valve that has a rim or lip at the top
of
> > the stem where I can get the seal only partially down. I can't get past
> > where the keepers sit and down onto the stem. What's up with this?
What
> > can I do in this situation? The last three valves have been ok. This
is
> > the first with the problem.
> >
> > Thanks for any suggestions.
> >
> > Bill
> >
> >
>
>

Re: valve stem has lip/rim can't get seal on
 

Bill, that sounds like the top of the valve has been pounded flat?

If so, then you have issues with that rocker arm for sure and likely the
push rod and/or the hydraulic lifter for that valve.

Was it physically loose before you unbolted it? Was the nut loose that
torques it on?

Have you had a bad tapping noise at idle in the past that 'maybe' went
away?

Are you the guy that had the 'timing ping' at idle? If so you just
found it.

Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's

William Oliveri wrote:
>
> Should I protect the area from filings and take a file and file the lip off?
>
> Thanks,
>
> Bill
>
> "William Oliveri" <wuji@bigvalley.net> wrote in message
> news:bvf197$ro51k$1@ID-193866.news.uni-berlin.de...
> > 83 CJ7 4.2L
> >
> > I'm on #1 cylinder and I have a valve that has a rim or lip at the top of
> > the stem where I can get the seal only partially down. I can't get past
> > where the keepers sit and down onto the stem. What's up with this? What
> > can I do in this situation? The last three valves have been ok. This is
> > the first with the problem.
> >
> > Thanks for any suggestions.
> >
> > Bill
> >
> >

Re: valve stem has lip/rim can't get seal on
 

Bill, that sounds like the top of the valve has been pounded flat?

If so, then you have issues with that rocker arm for sure and likely the
push rod and/or the hydraulic lifter for that valve.

Was it physically loose before you unbolted it? Was the nut loose that
torques it on?

Have you had a bad tapping noise at idle in the past that 'maybe' went
away?

Are you the guy that had the 'timing ping' at idle? If so you just
found it.

Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's

William Oliveri wrote:
>
> Should I protect the area from filings and take a file and file the lip off?
>
> Thanks,
>
> Bill
>
> "William Oliveri" <wuji@bigvalley.net> wrote in message
> news:bvf197$ro51k$1@ID-193866.news.uni-berlin.de...
> > 83 CJ7 4.2L
> >
> > I'm on #1 cylinder and I have a valve that has a rim or lip at the top of
> > the stem where I can get the seal only partially down. I can't get past
> > where the keepers sit and down onto the stem. What's up with this? What
> > can I do in this situation? The last three valves have been ok. This is
> > the first with the problem.
> >
> > Thanks for any suggestions.
> >
> > Bill
> >
> >

Re: valve stem has lip/rim can't get seal on
 

Bill, that sounds like the top of the valve has been pounded flat?

If so, then you have issues with that rocker arm for sure and likely the
push rod and/or the hydraulic lifter for that valve.

Was it physically loose before you unbolted it? Was the nut loose that
torques it on?

Have you had a bad tapping noise at idle in the past that 'maybe' went
away?

Are you the guy that had the 'timing ping' at idle? If so you just
found it.

Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's

William Oliveri wrote:
>
> Should I protect the area from filings and take a file and file the lip off?
>
> Thanks,
>
> Bill
>
> "William Oliveri" <wuji@bigvalley.net> wrote in message
> news:bvf197$ro51k$1@ID-193866.news.uni-berlin.de...
> > 83 CJ7 4.2L
> >
> > I'm on #1 cylinder and I have a valve that has a rim or lip at the top of
> > the stem where I can get the seal only partially down. I can't get past
> > where the keepers sit and down onto the stem. What's up with this? What
> > can I do in this situation? The last three valves have been ok. This is
> > the first with the problem.
> >
> > Thanks for any suggestions.
> >
> > Bill
> >
> >