Re: Towing a CJ-7 (Need proper procedures for it)
 

I don't believe that is right at all for the 300.

When the hubs are open, the front driveshaft does not move. Therefore I
think the oil gets slung from the front input shaft like my owners
manual says.

The owners manual for the 85 and 86 states you have to run the engine in
gear with the t-case in neutral every hundred miles or so to lube up the
t-case.

If locking the front hubs would keep it lubed up, you would think the
manual would say so to avoid having to stop and run the engine. etc...

Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's

Matt Macchiarolo wrote:
>
> Does the front output shaft sling the oil through the T-case on a Dana 300,
> or is it the input shaft? I seem to recall it was the front output shaft, so
> when flat-towing you could lock in the front hubs to keep it lubed, put the
> Tcase in Neutral, tranny in gear, and steering column unlocked.
>
> "Robert Bills" <rdbillsjr@aol.comxxxxxxxx> wrote in message
> news:20041102135850.01474.00000003@mb-m18.aol.com...
> > >what is the proper way to set the transfer and
> > >transmission and what gear should it be in while towing.
> >
> > Transfer case in neutral, transmission in 3rd gear. You can lock one of
> the
> > front hubs if you want, but it isn't really necessary.
> >
> > Before you head out, start the engine, run it at about 1200 or so rpm for
> a
> > minute + to sling oil throughout the transfer case. Stop every 200 miles
> or so
> > and repeat procedure.
> >
> > You do not need to remove driveshafts, just be sure that you sling the oil
> in
> > the transfer case on a regular basis.
> >
> > Als, be sure your steering column is NOT locked while you tow.
> >
> >
> >
> > Robert Bills
> > KG6LMV
> > Orange County CA
> >
> > '83 CJ-7
> > '46 Bantam BT3C
> > '87 Ford F250 4x4 Diesel
> > http://www.outdoorwire.com/4x4/jeep/...p-l/billsr.htm
> >

Re: Towing a CJ-7 (Need proper procedures for it)
 

I don't believe that is right at all for the 300.

When the hubs are open, the front driveshaft does not move. Therefore I
think the oil gets slung from the front input shaft like my owners
manual says.

The owners manual for the 85 and 86 states you have to run the engine in
gear with the t-case in neutral every hundred miles or so to lube up the
t-case.

If locking the front hubs would keep it lubed up, you would think the
manual would say so to avoid having to stop and run the engine. etc...

Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's

Matt Macchiarolo wrote:
>
> Does the front output shaft sling the oil through the T-case on a Dana 300,
> or is it the input shaft? I seem to recall it was the front output shaft, so
> when flat-towing you could lock in the front hubs to keep it lubed, put the
> Tcase in Neutral, tranny in gear, and steering column unlocked.
>
> "Robert Bills" <rdbillsjr@aol.comxxxxxxxx> wrote in message
> news:20041102135850.01474.00000003@mb-m18.aol.com...
> > >what is the proper way to set the transfer and
> > >transmission and what gear should it be in while towing.
> >
> > Transfer case in neutral, transmission in 3rd gear. You can lock one of
> the
> > front hubs if you want, but it isn't really necessary.
> >
> > Before you head out, start the engine, run it at about 1200 or so rpm for
> a
> > minute + to sling oil throughout the transfer case. Stop every 200 miles
> or so
> > and repeat procedure.
> >
> > You do not need to remove driveshafts, just be sure that you sling the oil
> in
> > the transfer case on a regular basis.
> >
> > Als, be sure your steering column is NOT locked while you tow.
> >
> >
> >
> > Robert Bills
> > KG6LMV
> > Orange County CA
> >
> > '83 CJ-7
> > '46 Bantam BT3C
> > '87 Ford F250 4x4 Diesel
> > http://www.outdoorwire.com/4x4/jeep/...p-l/billsr.htm
> >

Re: Towing a CJ-7 (Need proper procedures for it)
 

OK, I wasn't sure if it was the input shaft or front output shaft for the
300. If it was the output shaft, you could lock the hubs to provide
lubrication...perhaps some other Tcase does that.

"Mike Romain" <romainm@sympatico.ca> wrote in message
news:4187FDAA.C32914A4@sympatico.ca...
> I don't believe that is right at all for the 300.
>
> When the hubs are open, the front driveshaft does not move. Therefore I
> think the oil gets slung from the front input shaft like my owners
> manual says.
>
> The owners manual for the 85 and 86 states you have to run the engine in
> gear with the t-case in neutral every hundred miles or so to lube up the
> t-case.
>
> If locking the front hubs would keep it lubed up, you would think the
> manual would say so to avoid having to stop and run the engine. etc...
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Matt Macchiarolo wrote:
> >
> > Does the front output shaft sling the oil through the T-case on a Dana
300,
> > or is it the input shaft? I seem to recall it was the front output
shaft, so
> > when flat-towing you could lock in the front hubs to keep it lubed, put
the
> > Tcase in Neutral, tranny in gear, and steering column unlocked.
> >
> > "Robert Bills" <rdbillsjr@aol.comxxxxxxxx> wrote in message
> > news:20041102135850.01474.00000003@mb-m18.aol.com...
> > > >what is the proper way to set the transfer and
> > > >transmission and what gear should it be in while towing.
> > >
> > > Transfer case in neutral, transmission in 3rd gear. You can lock one
of
> > the
> > > front hubs if you want, but it isn't really necessary.
> > >
> > > Before you head out, start the engine, run it at about 1200 or so rpm
for
> > a
> > > minute + to sling oil throughout the transfer case. Stop every 200
miles
> > or so
> > > and repeat procedure.
> > >
> > > You do not need to remove driveshafts, just be sure that you sling the
oil
> > in
> > > the transfer case on a regular basis.
> > >
> > > Als, be sure your steering column is NOT locked while you tow.
> > >
> > >
> > >
> > > Robert Bills
> > > KG6LMV
> > > Orange County CA
> > >
> > > '83 CJ-7
> > > '46 Bantam BT3C
> > > '87 Ford F250 4x4 Diesel
> > > http://www.outdoorwire.com/4x4/jeep/...p-l/billsr.htm
> > >

Re: Towing a CJ-7 (Need proper procedures for it)
 

OK, I wasn't sure if it was the input shaft or front output shaft for the
300. If it was the output shaft, you could lock the hubs to provide
lubrication...perhaps some other Tcase does that.

"Mike Romain" <romainm@sympatico.ca> wrote in message
news:4187FDAA.C32914A4@sympatico.ca...
> I don't believe that is right at all for the 300.
>
> When the hubs are open, the front driveshaft does not move. Therefore I
> think the oil gets slung from the front input shaft like my owners
> manual says.
>
> The owners manual for the 85 and 86 states you have to run the engine in
> gear with the t-case in neutral every hundred miles or so to lube up the
> t-case.
>
> If locking the front hubs would keep it lubed up, you would think the
> manual would say so to avoid having to stop and run the engine. etc...
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Matt Macchiarolo wrote:
> >
> > Does the front output shaft sling the oil through the T-case on a Dana
300,
> > or is it the input shaft? I seem to recall it was the front output
shaft, so
> > when flat-towing you could lock in the front hubs to keep it lubed, put
the
> > Tcase in Neutral, tranny in gear, and steering column unlocked.
> >
> > "Robert Bills" <rdbillsjr@aol.comxxxxxxxx> wrote in message
> > news:20041102135850.01474.00000003@mb-m18.aol.com...
> > > >what is the proper way to set the transfer and
> > > >transmission and what gear should it be in while towing.
> > >
> > > Transfer case in neutral, transmission in 3rd gear. You can lock one
of
> > the
> > > front hubs if you want, but it isn't really necessary.
> > >
> > > Before you head out, start the engine, run it at about 1200 or so rpm
for
> > a
> > > minute + to sling oil throughout the transfer case. Stop every 200
miles
> > or so
> > > and repeat procedure.
> > >
> > > You do not need to remove driveshafts, just be sure that you sling the
oil
> > in
> > > the transfer case on a regular basis.
> > >
> > > Als, be sure your steering column is NOT locked while you tow.
> > >
> > >
> > >
> > > Robert Bills
> > > KG6LMV
> > > Orange County CA
> > >
> > > '83 CJ-7
> > > '46 Bantam BT3C
> > > '87 Ford F250 4x4 Diesel
> > > http://www.outdoorwire.com/4x4/jeep/...p-l/billsr.htm
> > >

Re: Towing a CJ-7 (Need proper procedures for it)
 

OK, I wasn't sure if it was the input shaft or front output shaft for the
300. If it was the output shaft, you could lock the hubs to provide
lubrication...perhaps some other Tcase does that.

"Mike Romain" <romainm@sympatico.ca> wrote in message
news:4187FDAA.C32914A4@sympatico.ca...
> I don't believe that is right at all for the 300.
>
> When the hubs are open, the front driveshaft does not move. Therefore I
> think the oil gets slung from the front input shaft like my owners
> manual says.
>
> The owners manual for the 85 and 86 states you have to run the engine in
> gear with the t-case in neutral every hundred miles or so to lube up the
> t-case.
>
> If locking the front hubs would keep it lubed up, you would think the
> manual would say so to avoid having to stop and run the engine. etc...
>
> Mike
> 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
> 88 Cherokee 235 BFG AT's
>
> Matt Macchiarolo wrote:
> >
> > Does the front output shaft sling the oil through the T-case on a Dana
300,
> > or is it the input shaft? I seem to recall it was the front output
shaft, so
> > when flat-towing you could lock in the front hubs to keep it lubed, put
the
> > Tcase in Neutral, tranny in gear, and steering column unlocked.
> >
> > "Robert Bills" <rdbillsjr@aol.comxxxxxxxx> wrote in message
> > news:20041102135850.01474.00000003@mb-m18.aol.com...
> > > >what is the proper way to set the transfer and
> > > >transmission and what gear should it be in while towing.
> > >
> > > Transfer case in neutral, transmission in 3rd gear. You can lock one
of
> > the
> > > front hubs if you want, but it isn't really necessary.
> > >
> > > Before you head out, start the engine, run it at about 1200 or so rpm
for
> > a
> > > minute + to sling oil throughout the transfer case. Stop every 200
miles
> > or so
> > > and repeat procedure.
> > >
> > > You do not need to remove driveshafts, just be sure that you sling the
oil
> > in
> > > the transfer case on a regular basis.
> > >
> > > Als, be sure your steering column is NOT locked while you tow.
> > >
> > >
> > >
> > > Robert Bills
> > > KG6LMV
> > > Orange County CA
> > >
> > > '83 CJ-7
> > > '46 Bantam BT3C
> > > '87 Ford F250 4x4 Diesel
> > > http://www.outdoorwire.com/4x4/jeep/...p-l/billsr.htm
> > >

Re: Towing a CJ-7 (Need proper procedures for it)
 

Why even put the wear and tear on the components in the first place. It's 8
small bolts/nuts and thats it....no stopping every X hundred of miles. My vote
is just remove the driveshaft or remove the rear end and wire it up (only 4
little bolts then)

Re: Towing a CJ-7 (Need proper procedures for it)
 

Why even put the wear and tear on the components in the first place. It's 8
small bolts/nuts and thats it....no stopping every X hundred of miles. My vote
is just remove the driveshaft or remove the rear end and wire it up (only 4
little bolts then)

Re: Towing a CJ-7 (Need proper procedures for it)
 

Why even put the wear and tear on the components in the first place. It's 8
small bolts/nuts and thats it....no stopping every X hundred of miles. My vote
is just remove the driveshaft or remove the rear end and wire it up (only 4
little bolts then)

Re: Towing a CJ-7 (Need proper procedures for it)
 

> Why even put the wear and tear on the components in the first place. It's
> 8
> small bolts/nuts and thats it....no stopping every X hundred of miles. My
> vote
> is just remove the driveshaft or remove the rear end and wire it up (only
> 4
> little bolts then)

Exactly!
When you're going 2000 miles stopping every 200 to run the engine sucks!

--
_____________________
HomeBrewer
85CJ7 (in Progress)
http://85cj7.blogspot.com/
99XJ Sport
Remove the xxx to reply!

"Onlyinajeepcj7" <onlyinajeepcj7@aol.com> wrote in message
news:20041102173116.25011.00000007@mb-m17.aol.com...

Re: Towing a CJ-7 (Need proper procedures for it)
 

> Why even put the wear and tear on the components in the first place. It's
> 8
> small bolts/nuts and thats it....no stopping every X hundred of miles. My
> vote
> is just remove the driveshaft or remove the rear end and wire it up (only
> 4
> little bolts then)

Exactly!
When you're going 2000 miles stopping every 200 to run the engine sucks!

--
_____________________
HomeBrewer
85CJ7 (in Progress)
http://85cj7.blogspot.com/
99XJ Sport
Remove the xxx to reply!

"Onlyinajeepcj7" <onlyinajeepcj7@aol.com> wrote in message
news:20041102173116.25011.00000007@mb-m17.aol.com...