|
Tail shaft bushing
Has anyone replaced the tail shaft bushing in a 96 Jeep GC.. Is it hard to
do in the car. Any special tools needed.. |
Re: Tail shaft bushing
"Gerald K4NHN" <gcromer@usit.net> wrote in message
news:oMTZh.6034$Ut6.409@newsread1.news.pas.earthli nk.net... > Has anyone replaced the tail shaft bushing in a 96 Jeep GC.. Is > it hard to do in the car. > Any special tools needed.. > You mean the "transfer case tail shaft bushing"? You would have to take the tail shaft housing off, press the old bushing out, and press the new bushing in. How do you know, why do you think, it is bad? If it is, the rear drive shaft front yoke probably is too. Earle |
Re: Tail shaft bushing
"Gerald K4NHN" <gcromer@usit.net> wrote in message
news:oMTZh.6034$Ut6.409@newsread1.news.pas.earthli nk.net... > Has anyone replaced the tail shaft bushing in a 96 Jeep GC.. Is > it hard to do in the car. > Any special tools needed.. > You mean the "transfer case tail shaft bushing"? You would have to take the tail shaft housing off, press the old bushing out, and press the new bushing in. How do you know, why do you think, it is bad? If it is, the rear drive shaft front yoke probably is too. Earle |
Re: Tail shaft bushing
"Gerald K4NHN" <gcromer@usit.net> wrote in message
news:oMTZh.6034$Ut6.409@newsread1.news.pas.earthli nk.net... > Has anyone replaced the tail shaft bushing in a 96 Jeep GC.. Is > it hard to do in the car. > Any special tools needed.. > You mean the "transfer case tail shaft bushing"? You would have to take the tail shaft housing off, press the old bushing out, and press the new bushing in. How do you know, why do you think, it is bad? If it is, the rear drive shaft front yoke probably is too. Earle |
Re: Tail shaft bushing
"Gerald K4NHN" <gcromer@usit.net> wrote in message
news:oMTZh.6034$Ut6.409@newsread1.news.pas.earthli nk.net... > Has anyone replaced the tail shaft bushing in a 96 Jeep GC.. Is > it hard to do in the car. > Any special tools needed.. > You mean the "transfer case tail shaft bushing"? You would have to take the tail shaft housing off, press the old bushing out, and press the new bushing in. How do you know, why do you think, it is bad? If it is, the rear drive shaft front yoke probably is too. Earle |
Re: Tail shaft bushing
Hi Earl
It where the rear drive shaft come out of the transmission. It's a 2 WD.. I can feel the play in the yoke by moving it up and down and right and left. A friend has the same Jeep and I can't move it at all.. I have a vibration that I can't find when I let off the gas with no load on the drive train. In the 50 to 75 mph range and I can hear it when it does it.. I've replace the front u-joint. It was bad on one plane and good in the other. The yoke didn't look bad, but I didn't put a mic on it... so..... The SUV has 275K mostly road miles on it.... I've been told that the bushing can be gotten out with out removing the rear housing. I'm waiting on the real shop manual to come in to see what it says. I was told that it can be punched inward and it will slide out. Also that there was a grove that a small punch will go between the housing and the bushing to force the bushing inward to relieve the pressure so it will come out... It's best to try and find out for sure before I start this... "Earle Horton" <earle@vascongado.usa> wrote in message news:46380bf2$0$31804$a82e2bb9@reader.athenanews.c om... > "Gerald K4NHN" <gcromer@usit.net> wrote in message > news:oMTZh.6034$Ut6.409@newsread1.news.pas.earthli nk.net... >> Has anyone replaced the tail shaft bushing in a 96 Jeep GC.. Is >> it hard to do in the car. >> Any special tools needed.. >> > > You mean the "transfer case tail shaft bushing"? You would have to take > the > tail shaft housing off, press the old bushing out, and press the new > bushing > in. How do you know, why do you think, it is bad? If it is, the rear > drive > shaft front yoke probably is too. > > Earle > > |
Re: Tail shaft bushing
Hi Earl
It where the rear drive shaft come out of the transmission. It's a 2 WD.. I can feel the play in the yoke by moving it up and down and right and left. A friend has the same Jeep and I can't move it at all.. I have a vibration that I can't find when I let off the gas with no load on the drive train. In the 50 to 75 mph range and I can hear it when it does it.. I've replace the front u-joint. It was bad on one plane and good in the other. The yoke didn't look bad, but I didn't put a mic on it... so..... The SUV has 275K mostly road miles on it.... I've been told that the bushing can be gotten out with out removing the rear housing. I'm waiting on the real shop manual to come in to see what it says. I was told that it can be punched inward and it will slide out. Also that there was a grove that a small punch will go between the housing and the bushing to force the bushing inward to relieve the pressure so it will come out... It's best to try and find out for sure before I start this... "Earle Horton" <earle@vascongado.usa> wrote in message news:46380bf2$0$31804$a82e2bb9@reader.athenanews.c om... > "Gerald K4NHN" <gcromer@usit.net> wrote in message > news:oMTZh.6034$Ut6.409@newsread1.news.pas.earthli nk.net... >> Has anyone replaced the tail shaft bushing in a 96 Jeep GC.. Is >> it hard to do in the car. >> Any special tools needed.. >> > > You mean the "transfer case tail shaft bushing"? You would have to take > the > tail shaft housing off, press the old bushing out, and press the new > bushing > in. How do you know, why do you think, it is bad? If it is, the rear > drive > shaft front yoke probably is too. > > Earle > > |
Re: Tail shaft bushing
Hi Earl
It where the rear drive shaft come out of the transmission. It's a 2 WD.. I can feel the play in the yoke by moving it up and down and right and left. A friend has the same Jeep and I can't move it at all.. I have a vibration that I can't find when I let off the gas with no load on the drive train. In the 50 to 75 mph range and I can hear it when it does it.. I've replace the front u-joint. It was bad on one plane and good in the other. The yoke didn't look bad, but I didn't put a mic on it... so..... The SUV has 275K mostly road miles on it.... I've been told that the bushing can be gotten out with out removing the rear housing. I'm waiting on the real shop manual to come in to see what it says. I was told that it can be punched inward and it will slide out. Also that there was a grove that a small punch will go between the housing and the bushing to force the bushing inward to relieve the pressure so it will come out... It's best to try and find out for sure before I start this... "Earle Horton" <earle@vascongado.usa> wrote in message news:46380bf2$0$31804$a82e2bb9@reader.athenanews.c om... > "Gerald K4NHN" <gcromer@usit.net> wrote in message > news:oMTZh.6034$Ut6.409@newsread1.news.pas.earthli nk.net... >> Has anyone replaced the tail shaft bushing in a 96 Jeep GC.. Is >> it hard to do in the car. >> Any special tools needed.. >> > > You mean the "transfer case tail shaft bushing"? You would have to take > the > tail shaft housing off, press the old bushing out, and press the new > bushing > in. How do you know, why do you think, it is bad? If it is, the rear > drive > shaft front yoke probably is too. > > Earle > > |
Re: Tail shaft bushing
Hi Earl
It where the rear drive shaft come out of the transmission. It's a 2 WD.. I can feel the play in the yoke by moving it up and down and right and left. A friend has the same Jeep and I can't move it at all.. I have a vibration that I can't find when I let off the gas with no load on the drive train. In the 50 to 75 mph range and I can hear it when it does it.. I've replace the front u-joint. It was bad on one plane and good in the other. The yoke didn't look bad, but I didn't put a mic on it... so..... The SUV has 275K mostly road miles on it.... I've been told that the bushing can be gotten out with out removing the rear housing. I'm waiting on the real shop manual to come in to see what it says. I was told that it can be punched inward and it will slide out. Also that there was a grove that a small punch will go between the housing and the bushing to force the bushing inward to relieve the pressure so it will come out... It's best to try and find out for sure before I start this... "Earle Horton" <earle@vascongado.usa> wrote in message news:46380bf2$0$31804$a82e2bb9@reader.athenanews.c om... > "Gerald K4NHN" <gcromer@usit.net> wrote in message > news:oMTZh.6034$Ut6.409@newsread1.news.pas.earthli nk.net... >> Has anyone replaced the tail shaft bushing in a 96 Jeep GC.. Is >> it hard to do in the car. >> Any special tools needed.. >> > > You mean the "transfer case tail shaft bushing"? You would have to take > the > tail shaft housing off, press the old bushing out, and press the new > bushing > in. How do you know, why do you think, it is bad? If it is, the rear > drive > shaft front yoke probably is too. > > Earle > > |
Re: Tail shaft bushing
Chances are good that your bad universal joint caused the bushing damage.
If you still have the vibration, then you probably have something else going on other than the bushing, unless the play you are describing is extreme. I can't picture punching inward on the bushing to relieve the pressure, because the transmission output shaft is still there to get in the way. Installing the new bushing is going to present the same sort of problem. The best bet is to wait for the shop manual, but many times the extension housing, the part that the bushing is in, can be removed with the transmission still in the car. Draining the transmission is probably a good idea first, but the shop manual will discuss that. Earle "Gerald K4NHN" <gcromer@usit.net> wrote in message news:O81_h.2874$296.1087@newsread4.news.pas.earthl ink.net... > Hi Earl > It where the rear drive shaft come out of the transmission. It's a 2 WD.. I > can feel the play in the yoke by moving it up and down and right and left. A > friend has the same Jeep and I can't move it at all.. > > I have a vibration that I can't find when I let off the gas with no load on > the drive train. In the 50 to 75 mph range and I can hear it when it does > it.. I've replace the front u-joint. It was bad on one plane and good in the > other. The yoke didn't look bad, but I didn't put a mic on it... so..... The > SUV has 275K mostly road miles on it.... > > I've been told that the bushing can be gotten out with out removing the rear > housing. I'm waiting on the real shop manual to come in to see what it says. > I was told that it can be punched inward and it will slide out. Also that > there was a grove that a small punch will go between the housing and the > bushing to force the bushing inward to relieve the pressure so it will come > out... It's best to try and find out for sure before I start this... > > > "Earle Horton" <earle@vascongado.usa> wrote in message > news:46380bf2$0$31804$a82e2bb9@reader.athenanews.c om... > > "Gerald K4NHN" <gcromer@usit.net> wrote in message > > news:oMTZh.6034$Ut6.409@newsread1.news.pas.earthli nk.net... > >> Has anyone replaced the tail shaft bushing in a 96 Jeep GC.. Is > >> it hard to do in the car. > >> Any special tools needed.. > >> > > > > You mean the "transfer case tail shaft bushing"? You would have to take > > the > > tail shaft housing off, press the old bushing out, and press the new > > bushing > > in. How do you know, why do you think, it is bad? If it is, the rear > > drive > > shaft front yoke probably is too. > > > > Earle > > > > > > |
Re: Tail shaft bushing
Chances are good that your bad universal joint caused the bushing damage.
If you still have the vibration, then you probably have something else going on other than the bushing, unless the play you are describing is extreme. I can't picture punching inward on the bushing to relieve the pressure, because the transmission output shaft is still there to get in the way. Installing the new bushing is going to present the same sort of problem. The best bet is to wait for the shop manual, but many times the extension housing, the part that the bushing is in, can be removed with the transmission still in the car. Draining the transmission is probably a good idea first, but the shop manual will discuss that. Earle "Gerald K4NHN" <gcromer@usit.net> wrote in message news:O81_h.2874$296.1087@newsread4.news.pas.earthl ink.net... > Hi Earl > It where the rear drive shaft come out of the transmission. It's a 2 WD.. I > can feel the play in the yoke by moving it up and down and right and left. A > friend has the same Jeep and I can't move it at all.. > > I have a vibration that I can't find when I let off the gas with no load on > the drive train. In the 50 to 75 mph range and I can hear it when it does > it.. I've replace the front u-joint. It was bad on one plane and good in the > other. The yoke didn't look bad, but I didn't put a mic on it... so..... The > SUV has 275K mostly road miles on it.... > > I've been told that the bushing can be gotten out with out removing the rear > housing. I'm waiting on the real shop manual to come in to see what it says. > I was told that it can be punched inward and it will slide out. Also that > there was a grove that a small punch will go between the housing and the > bushing to force the bushing inward to relieve the pressure so it will come > out... It's best to try and find out for sure before I start this... > > > "Earle Horton" <earle@vascongado.usa> wrote in message > news:46380bf2$0$31804$a82e2bb9@reader.athenanews.c om... > > "Gerald K4NHN" <gcromer@usit.net> wrote in message > > news:oMTZh.6034$Ut6.409@newsread1.news.pas.earthli nk.net... > >> Has anyone replaced the tail shaft bushing in a 96 Jeep GC.. Is > >> it hard to do in the car. > >> Any special tools needed.. > >> > > > > You mean the "transfer case tail shaft bushing"? You would have to take > > the > > tail shaft housing off, press the old bushing out, and press the new > > bushing > > in. How do you know, why do you think, it is bad? If it is, the rear > > drive > > shaft front yoke probably is too. > > > > Earle > > > > > > |
Re: Tail shaft bushing
Chances are good that your bad universal joint caused the bushing damage.
If you still have the vibration, then you probably have something else going on other than the bushing, unless the play you are describing is extreme. I can't picture punching inward on the bushing to relieve the pressure, because the transmission output shaft is still there to get in the way. Installing the new bushing is going to present the same sort of problem. The best bet is to wait for the shop manual, but many times the extension housing, the part that the bushing is in, can be removed with the transmission still in the car. Draining the transmission is probably a good idea first, but the shop manual will discuss that. Earle "Gerald K4NHN" <gcromer@usit.net> wrote in message news:O81_h.2874$296.1087@newsread4.news.pas.earthl ink.net... > Hi Earl > It where the rear drive shaft come out of the transmission. It's a 2 WD.. I > can feel the play in the yoke by moving it up and down and right and left. A > friend has the same Jeep and I can't move it at all.. > > I have a vibration that I can't find when I let off the gas with no load on > the drive train. In the 50 to 75 mph range and I can hear it when it does > it.. I've replace the front u-joint. It was bad on one plane and good in the > other. The yoke didn't look bad, but I didn't put a mic on it... so..... The > SUV has 275K mostly road miles on it.... > > I've been told that the bushing can be gotten out with out removing the rear > housing. I'm waiting on the real shop manual to come in to see what it says. > I was told that it can be punched inward and it will slide out. Also that > there was a grove that a small punch will go between the housing and the > bushing to force the bushing inward to relieve the pressure so it will come > out... It's best to try and find out for sure before I start this... > > > "Earle Horton" <earle@vascongado.usa> wrote in message > news:46380bf2$0$31804$a82e2bb9@reader.athenanews.c om... > > "Gerald K4NHN" <gcromer@usit.net> wrote in message > > news:oMTZh.6034$Ut6.409@newsread1.news.pas.earthli nk.net... > >> Has anyone replaced the tail shaft bushing in a 96 Jeep GC.. Is > >> it hard to do in the car. > >> Any special tools needed.. > >> > > > > You mean the "transfer case tail shaft bushing"? You would have to take > > the > > tail shaft housing off, press the old bushing out, and press the new > > bushing > > in. How do you know, why do you think, it is bad? If it is, the rear > > drive > > shaft front yoke probably is too. > > > > Earle > > > > > > |
Re: Tail shaft bushing
Chances are good that your bad universal joint caused the bushing damage.
If you still have the vibration, then you probably have something else going on other than the bushing, unless the play you are describing is extreme. I can't picture punching inward on the bushing to relieve the pressure, because the transmission output shaft is still there to get in the way. Installing the new bushing is going to present the same sort of problem. The best bet is to wait for the shop manual, but many times the extension housing, the part that the bushing is in, can be removed with the transmission still in the car. Draining the transmission is probably a good idea first, but the shop manual will discuss that. Earle "Gerald K4NHN" <gcromer@usit.net> wrote in message news:O81_h.2874$296.1087@newsread4.news.pas.earthl ink.net... > Hi Earl > It where the rear drive shaft come out of the transmission. It's a 2 WD.. I > can feel the play in the yoke by moving it up and down and right and left. A > friend has the same Jeep and I can't move it at all.. > > I have a vibration that I can't find when I let off the gas with no load on > the drive train. In the 50 to 75 mph range and I can hear it when it does > it.. I've replace the front u-joint. It was bad on one plane and good in the > other. The yoke didn't look bad, but I didn't put a mic on it... so..... The > SUV has 275K mostly road miles on it.... > > I've been told that the bushing can be gotten out with out removing the rear > housing. I'm waiting on the real shop manual to come in to see what it says. > I was told that it can be punched inward and it will slide out. Also that > there was a grove that a small punch will go between the housing and the > bushing to force the bushing inward to relieve the pressure so it will come > out... It's best to try and find out for sure before I start this... > > > "Earle Horton" <earle@vascongado.usa> wrote in message > news:46380bf2$0$31804$a82e2bb9@reader.athenanews.c om... > > "Gerald K4NHN" <gcromer@usit.net> wrote in message > > news:oMTZh.6034$Ut6.409@newsread1.news.pas.earthli nk.net... > >> Has anyone replaced the tail shaft bushing in a 96 Jeep GC.. Is > >> it hard to do in the car. > >> Any special tools needed.. > >> > > > > You mean the "transfer case tail shaft bushing"? You would have to take > > the > > tail shaft housing off, press the old bushing out, and press the new > > bushing > > in. How do you know, why do you think, it is bad? If it is, the rear > > drive > > shaft front yoke probably is too. > > > > Earle > > > > > > |
Re: Tail shaft bushing
The play wasn't extreme, but I could feel and hear it as I moved it back and
forth. .. "Earle Horton" <earle@vascongado.usa> wrote in message news:4638a11e$0$31833$a82e2bb9@reader.athenanews.c om... > Chances are good that your bad universal joint caused the bushing damage. > If you still have the vibration, then you probably have something else > going > on other than the bushing, unless the play you are describing is extreme. > I > can't picture punching inward on the bushing to relieve the pressure, > because the transmission output shaft is still there to get in the way. > Installing the new bushing is going to present the same sort of problem. > The best bet is to wait for the shop manual, but many times the extension > housing, the part that the bushing is in, can be removed with the > transmission still in the car. Draining the transmission is probably a > good > idea first, but the shop manual will discuss that. > > Earle > > "Gerald K4NHN" <gcromer@usit.net> wrote in message > news:O81_h.2874$296.1087@newsread4.news.pas.earthl ink.net... >> Hi Earl >> It where the rear drive shaft come out of the transmission. It's a 2 WD.. > I >> can feel the play in the yoke by moving it up and down and right and >> left. > A >> friend has the same Jeep and I can't move it at all.. >> >> I have a vibration that I can't find when I let off the gas with no load > on >> the drive train. In the 50 to 75 mph range and I can hear it when it does >> it.. I've replace the front u-joint. It was bad on one plane and good in > the >> other. The yoke didn't look bad, but I didn't put a mic on it... so..... > The >> SUV has 275K mostly road miles on it.... >> >> I've been told that the bushing can be gotten out with out removing the > rear >> housing. I'm waiting on the real shop manual to come in to see what it > says. >> I was told that it can be punched inward and it will slide out. Also that >> there was a grove that a small punch will go between the housing and the >> bushing to force the bushing inward to relieve the pressure so it will > come >> out... It's best to try and find out for sure before I start this... >> >> >> "Earle Horton" <earle@vascongado.usa> wrote in message >> news:46380bf2$0$31804$a82e2bb9@reader.athenanews.c om... >> > "Gerald K4NHN" <gcromer@usit.net> wrote in message >> > news:oMTZh.6034$Ut6.409@newsread1.news.pas.earthli nk.net... >> >> Has anyone replaced the tail shaft bushing in a 96 Jeep GC.. Is >> >> it hard to do in the car. >> >> Any special tools needed.. >> >> >> > >> > You mean the "transfer case tail shaft bushing"? You would have to >> > take >> > the >> > tail shaft housing off, press the old bushing out, and press the new >> > bushing >> > in. How do you know, why do you think, it is bad? If it is, the rear >> > drive >> > shaft front yoke probably is too. >> > >> > Earle >> > >> > >> >> > > |
Re: Tail shaft bushing
The play wasn't extreme, but I could feel and hear it as I moved it back and
forth. .. "Earle Horton" <earle@vascongado.usa> wrote in message news:4638a11e$0$31833$a82e2bb9@reader.athenanews.c om... > Chances are good that your bad universal joint caused the bushing damage. > If you still have the vibration, then you probably have something else > going > on other than the bushing, unless the play you are describing is extreme. > I > can't picture punching inward on the bushing to relieve the pressure, > because the transmission output shaft is still there to get in the way. > Installing the new bushing is going to present the same sort of problem. > The best bet is to wait for the shop manual, but many times the extension > housing, the part that the bushing is in, can be removed with the > transmission still in the car. Draining the transmission is probably a > good > idea first, but the shop manual will discuss that. > > Earle > > "Gerald K4NHN" <gcromer@usit.net> wrote in message > news:O81_h.2874$296.1087@newsread4.news.pas.earthl ink.net... >> Hi Earl >> It where the rear drive shaft come out of the transmission. It's a 2 WD.. > I >> can feel the play in the yoke by moving it up and down and right and >> left. > A >> friend has the same Jeep and I can't move it at all.. >> >> I have a vibration that I can't find when I let off the gas with no load > on >> the drive train. In the 50 to 75 mph range and I can hear it when it does >> it.. I've replace the front u-joint. It was bad on one plane and good in > the >> other. The yoke didn't look bad, but I didn't put a mic on it... so..... > The >> SUV has 275K mostly road miles on it.... >> >> I've been told that the bushing can be gotten out with out removing the > rear >> housing. I'm waiting on the real shop manual to come in to see what it > says. >> I was told that it can be punched inward and it will slide out. Also that >> there was a grove that a small punch will go between the housing and the >> bushing to force the bushing inward to relieve the pressure so it will > come >> out... It's best to try and find out for sure before I start this... >> >> >> "Earle Horton" <earle@vascongado.usa> wrote in message >> news:46380bf2$0$31804$a82e2bb9@reader.athenanews.c om... >> > "Gerald K4NHN" <gcromer@usit.net> wrote in message >> > news:oMTZh.6034$Ut6.409@newsread1.news.pas.earthli nk.net... >> >> Has anyone replaced the tail shaft bushing in a 96 Jeep GC.. Is >> >> it hard to do in the car. >> >> Any special tools needed.. >> >> >> > >> > You mean the "transfer case tail shaft bushing"? You would have to >> > take >> > the >> > tail shaft housing off, press the old bushing out, and press the new >> > bushing >> > in. How do you know, why do you think, it is bad? If it is, the rear >> > drive >> > shaft front yoke probably is too. >> > >> > Earle >> > >> > >> >> > > |
Re: Tail shaft bushing
The play wasn't extreme, but I could feel and hear it as I moved it back and
forth. .. "Earle Horton" <earle@vascongado.usa> wrote in message news:4638a11e$0$31833$a82e2bb9@reader.athenanews.c om... > Chances are good that your bad universal joint caused the bushing damage. > If you still have the vibration, then you probably have something else > going > on other than the bushing, unless the play you are describing is extreme. > I > can't picture punching inward on the bushing to relieve the pressure, > because the transmission output shaft is still there to get in the way. > Installing the new bushing is going to present the same sort of problem. > The best bet is to wait for the shop manual, but many times the extension > housing, the part that the bushing is in, can be removed with the > transmission still in the car. Draining the transmission is probably a > good > idea first, but the shop manual will discuss that. > > Earle > > "Gerald K4NHN" <gcromer@usit.net> wrote in message > news:O81_h.2874$296.1087@newsread4.news.pas.earthl ink.net... >> Hi Earl >> It where the rear drive shaft come out of the transmission. It's a 2 WD.. > I >> can feel the play in the yoke by moving it up and down and right and >> left. > A >> friend has the same Jeep and I can't move it at all.. >> >> I have a vibration that I can't find when I let off the gas with no load > on >> the drive train. In the 50 to 75 mph range and I can hear it when it does >> it.. I've replace the front u-joint. It was bad on one plane and good in > the >> other. The yoke didn't look bad, but I didn't put a mic on it... so..... > The >> SUV has 275K mostly road miles on it.... >> >> I've been told that the bushing can be gotten out with out removing the > rear >> housing. I'm waiting on the real shop manual to come in to see what it > says. >> I was told that it can be punched inward and it will slide out. Also that >> there was a grove that a small punch will go between the housing and the >> bushing to force the bushing inward to relieve the pressure so it will > come >> out... It's best to try and find out for sure before I start this... >> >> >> "Earle Horton" <earle@vascongado.usa> wrote in message >> news:46380bf2$0$31804$a82e2bb9@reader.athenanews.c om... >> > "Gerald K4NHN" <gcromer@usit.net> wrote in message >> > news:oMTZh.6034$Ut6.409@newsread1.news.pas.earthli nk.net... >> >> Has anyone replaced the tail shaft bushing in a 96 Jeep GC.. Is >> >> it hard to do in the car. >> >> Any special tools needed.. >> >> >> > >> > You mean the "transfer case tail shaft bushing"? You would have to >> > take >> > the >> > tail shaft housing off, press the old bushing out, and press the new >> > bushing >> > in. How do you know, why do you think, it is bad? If it is, the rear >> > drive >> > shaft front yoke probably is too. >> > >> > Earle >> > >> > >> >> > > |
Re: Tail shaft bushing
The play wasn't extreme, but I could feel and hear it as I moved it back and
forth. .. "Earle Horton" <earle@vascongado.usa> wrote in message news:4638a11e$0$31833$a82e2bb9@reader.athenanews.c om... > Chances are good that your bad universal joint caused the bushing damage. > If you still have the vibration, then you probably have something else > going > on other than the bushing, unless the play you are describing is extreme. > I > can't picture punching inward on the bushing to relieve the pressure, > because the transmission output shaft is still there to get in the way. > Installing the new bushing is going to present the same sort of problem. > The best bet is to wait for the shop manual, but many times the extension > housing, the part that the bushing is in, can be removed with the > transmission still in the car. Draining the transmission is probably a > good > idea first, but the shop manual will discuss that. > > Earle > > "Gerald K4NHN" <gcromer@usit.net> wrote in message > news:O81_h.2874$296.1087@newsread4.news.pas.earthl ink.net... >> Hi Earl >> It where the rear drive shaft come out of the transmission. It's a 2 WD.. > I >> can feel the play in the yoke by moving it up and down and right and >> left. > A >> friend has the same Jeep and I can't move it at all.. >> >> I have a vibration that I can't find when I let off the gas with no load > on >> the drive train. In the 50 to 75 mph range and I can hear it when it does >> it.. I've replace the front u-joint. It was bad on one plane and good in > the >> other. The yoke didn't look bad, but I didn't put a mic on it... so..... > The >> SUV has 275K mostly road miles on it.... >> >> I've been told that the bushing can be gotten out with out removing the > rear >> housing. I'm waiting on the real shop manual to come in to see what it > says. >> I was told that it can be punched inward and it will slide out. Also that >> there was a grove that a small punch will go between the housing and the >> bushing to force the bushing inward to relieve the pressure so it will > come >> out... It's best to try and find out for sure before I start this... >> >> >> "Earle Horton" <earle@vascongado.usa> wrote in message >> news:46380bf2$0$31804$a82e2bb9@reader.athenanews.c om... >> > "Gerald K4NHN" <gcromer@usit.net> wrote in message >> > news:oMTZh.6034$Ut6.409@newsread1.news.pas.earthli nk.net... >> >> Has anyone replaced the tail shaft bushing in a 96 Jeep GC.. Is >> >> it hard to do in the car. >> >> Any special tools needed.. >> >> >> > >> > You mean the "transfer case tail shaft bushing"? You would have to >> > take >> > the >> > tail shaft housing off, press the old bushing out, and press the new >> > bushing >> > in. How do you know, why do you think, it is bad? If it is, the rear >> > drive >> > shaft front yoke probably is too. >> > >> > Earle >> > >> > >> >> > > |
Re: Tail shaft bushing
What really holds that shaft in place, is a ball bearing inside the housing.
The bushing you are talking about is reinforcement for the end of the shaft, because it sticks out pretty far from the bearing. You can live with a little play, but that shop manual you ordered should tell you how much is acceptable. If you can rent, buy or borrow a dial gauge, you can quantify the play you have. Earle "Gerald K4NHN" <gcromer@usit.net> wrote in message news:_O3_h.7508$j63.4011@newsread2.news.pas.earthl ink.net... > The play wasn't extreme, but I could feel and hear it as I moved it back and > forth. > . > > "Earle Horton" <earle@vascongado.usa> wrote in message > news:4638a11e$0$31833$a82e2bb9@reader.athenanews.c om... > > Chances are good that your bad universal joint caused the bushing damage. > > If you still have the vibration, then you probably have something else > > going > > on other than the bushing, unless the play you are describing is extreme. > > I > > can't picture punching inward on the bushing to relieve the pressure, > > because the transmission output shaft is still there to get in the way. > > Installing the new bushing is going to present the same sort of problem. > > The best bet is to wait for the shop manual, but many times the extension > > housing, the part that the bushing is in, can be removed with the > > transmission still in the car. Draining the transmission is probably a > > good > > idea first, but the shop manual will discuss that. > > > > Earle > > > > "Gerald K4NHN" <gcromer@usit.net> wrote in message > > news:O81_h.2874$296.1087@newsread4.news.pas.earthl ink.net... > >> Hi Earl > >> It where the rear drive shaft come out of the transmission. It's a 2 WD.. > > I > >> can feel the play in the yoke by moving it up and down and right and > >> left. > > A > >> friend has the same Jeep and I can't move it at all.. > >> > >> I have a vibration that I can't find when I let off the gas with no load > > on > >> the drive train. In the 50 to 75 mph range and I can hear it when it does > >> it.. I've replace the front u-joint. It was bad on one plane and good in > > the > >> other. The yoke didn't look bad, but I didn't put a mic on it... so..... > > The > >> SUV has 275K mostly road miles on it.... > >> > >> I've been told that the bushing can be gotten out with out removing the > > rear > >> housing. I'm waiting on the real shop manual to come in to see what it > > says. > >> I was told that it can be punched inward and it will slide out. Also that > >> there was a grove that a small punch will go between the housing and the > >> bushing to force the bushing inward to relieve the pressure so it will > > come > >> out... It's best to try and find out for sure before I start this... > >> > >> > >> "Earle Horton" <earle@vascongado.usa> wrote in message > >> news:46380bf2$0$31804$a82e2bb9@reader.athenanews.c om... > >> > "Gerald K4NHN" <gcromer@usit.net> wrote in message > >> > news:oMTZh.6034$Ut6.409@newsread1.news.pas.earthli nk.net... > >> >> Has anyone replaced the tail shaft bushing in a 96 Jeep GC.. Is > >> >> it hard to do in the car. > >> >> Any special tools needed.. > >> >> > >> > > >> > You mean the "transfer case tail shaft bushing"? You would have to > >> > take > >> > the > >> > tail shaft housing off, press the old bushing out, and press the new > >> > bushing > >> > in. How do you know, why do you think, it is bad? If it is, the rear > >> > drive > >> > shaft front yoke probably is too. > >> > > >> > Earle > >> > > >> > > >> > >> > > > > > > |
Re: Tail shaft bushing
What really holds that shaft in place, is a ball bearing inside the housing.
The bushing you are talking about is reinforcement for the end of the shaft, because it sticks out pretty far from the bearing. You can live with a little play, but that shop manual you ordered should tell you how much is acceptable. If you can rent, buy or borrow a dial gauge, you can quantify the play you have. Earle "Gerald K4NHN" <gcromer@usit.net> wrote in message news:_O3_h.7508$j63.4011@newsread2.news.pas.earthl ink.net... > The play wasn't extreme, but I could feel and hear it as I moved it back and > forth. > . > > "Earle Horton" <earle@vascongado.usa> wrote in message > news:4638a11e$0$31833$a82e2bb9@reader.athenanews.c om... > > Chances are good that your bad universal joint caused the bushing damage. > > If you still have the vibration, then you probably have something else > > going > > on other than the bushing, unless the play you are describing is extreme. > > I > > can't picture punching inward on the bushing to relieve the pressure, > > because the transmission output shaft is still there to get in the way. > > Installing the new bushing is going to present the same sort of problem. > > The best bet is to wait for the shop manual, but many times the extension > > housing, the part that the bushing is in, can be removed with the > > transmission still in the car. Draining the transmission is probably a > > good > > idea first, but the shop manual will discuss that. > > > > Earle > > > > "Gerald K4NHN" <gcromer@usit.net> wrote in message > > news:O81_h.2874$296.1087@newsread4.news.pas.earthl ink.net... > >> Hi Earl > >> It where the rear drive shaft come out of the transmission. It's a 2 WD.. > > I > >> can feel the play in the yoke by moving it up and down and right and > >> left. > > A > >> friend has the same Jeep and I can't move it at all.. > >> > >> I have a vibration that I can't find when I let off the gas with no load > > on > >> the drive train. In the 50 to 75 mph range and I can hear it when it does > >> it.. I've replace the front u-joint. It was bad on one plane and good in > > the > >> other. The yoke didn't look bad, but I didn't put a mic on it... so..... > > The > >> SUV has 275K mostly road miles on it.... > >> > >> I've been told that the bushing can be gotten out with out removing the > > rear > >> housing. I'm waiting on the real shop manual to come in to see what it > > says. > >> I was told that it can be punched inward and it will slide out. Also that > >> there was a grove that a small punch will go between the housing and the > >> bushing to force the bushing inward to relieve the pressure so it will > > come > >> out... It's best to try and find out for sure before I start this... > >> > >> > >> "Earle Horton" <earle@vascongado.usa> wrote in message > >> news:46380bf2$0$31804$a82e2bb9@reader.athenanews.c om... > >> > "Gerald K4NHN" <gcromer@usit.net> wrote in message > >> > news:oMTZh.6034$Ut6.409@newsread1.news.pas.earthli nk.net... > >> >> Has anyone replaced the tail shaft bushing in a 96 Jeep GC.. Is > >> >> it hard to do in the car. > >> >> Any special tools needed.. > >> >> > >> > > >> > You mean the "transfer case tail shaft bushing"? You would have to > >> > take > >> > the > >> > tail shaft housing off, press the old bushing out, and press the new > >> > bushing > >> > in. How do you know, why do you think, it is bad? If it is, the rear > >> > drive > >> > shaft front yoke probably is too. > >> > > >> > Earle > >> > > >> > > >> > >> > > > > > > |
Re: Tail shaft bushing
What really holds that shaft in place, is a ball bearing inside the housing.
The bushing you are talking about is reinforcement for the end of the shaft, because it sticks out pretty far from the bearing. You can live with a little play, but that shop manual you ordered should tell you how much is acceptable. If you can rent, buy or borrow a dial gauge, you can quantify the play you have. Earle "Gerald K4NHN" <gcromer@usit.net> wrote in message news:_O3_h.7508$j63.4011@newsread2.news.pas.earthl ink.net... > The play wasn't extreme, but I could feel and hear it as I moved it back and > forth. > . > > "Earle Horton" <earle@vascongado.usa> wrote in message > news:4638a11e$0$31833$a82e2bb9@reader.athenanews.c om... > > Chances are good that your bad universal joint caused the bushing damage. > > If you still have the vibration, then you probably have something else > > going > > on other than the bushing, unless the play you are describing is extreme. > > I > > can't picture punching inward on the bushing to relieve the pressure, > > because the transmission output shaft is still there to get in the way. > > Installing the new bushing is going to present the same sort of problem. > > The best bet is to wait for the shop manual, but many times the extension > > housing, the part that the bushing is in, can be removed with the > > transmission still in the car. Draining the transmission is probably a > > good > > idea first, but the shop manual will discuss that. > > > > Earle > > > > "Gerald K4NHN" <gcromer@usit.net> wrote in message > > news:O81_h.2874$296.1087@newsread4.news.pas.earthl ink.net... > >> Hi Earl > >> It where the rear drive shaft come out of the transmission. It's a 2 WD.. > > I > >> can feel the play in the yoke by moving it up and down and right and > >> left. > > A > >> friend has the same Jeep and I can't move it at all.. > >> > >> I have a vibration that I can't find when I let off the gas with no load > > on > >> the drive train. In the 50 to 75 mph range and I can hear it when it does > >> it.. I've replace the front u-joint. It was bad on one plane and good in > > the > >> other. The yoke didn't look bad, but I didn't put a mic on it... so..... > > The > >> SUV has 275K mostly road miles on it.... > >> > >> I've been told that the bushing can be gotten out with out removing the > > rear > >> housing. I'm waiting on the real shop manual to come in to see what it > > says. > >> I was told that it can be punched inward and it will slide out. Also that > >> there was a grove that a small punch will go between the housing and the > >> bushing to force the bushing inward to relieve the pressure so it will > > come > >> out... It's best to try and find out for sure before I start this... > >> > >> > >> "Earle Horton" <earle@vascongado.usa> wrote in message > >> news:46380bf2$0$31804$a82e2bb9@reader.athenanews.c om... > >> > "Gerald K4NHN" <gcromer@usit.net> wrote in message > >> > news:oMTZh.6034$Ut6.409@newsread1.news.pas.earthli nk.net... > >> >> Has anyone replaced the tail shaft bushing in a 96 Jeep GC.. Is > >> >> it hard to do in the car. > >> >> Any special tools needed.. > >> >> > >> > > >> > You mean the "transfer case tail shaft bushing"? You would have to > >> > take > >> > the > >> > tail shaft housing off, press the old bushing out, and press the new > >> > bushing > >> > in. How do you know, why do you think, it is bad? If it is, the rear > >> > drive > >> > shaft front yoke probably is too. > >> > > >> > Earle > >> > > >> > > >> > >> > > > > > > |
Re: Tail shaft bushing
What really holds that shaft in place, is a ball bearing inside the housing.
The bushing you are talking about is reinforcement for the end of the shaft, because it sticks out pretty far from the bearing. You can live with a little play, but that shop manual you ordered should tell you how much is acceptable. If you can rent, buy or borrow a dial gauge, you can quantify the play you have. Earle "Gerald K4NHN" <gcromer@usit.net> wrote in message news:_O3_h.7508$j63.4011@newsread2.news.pas.earthl ink.net... > The play wasn't extreme, but I could feel and hear it as I moved it back and > forth. > . > > "Earle Horton" <earle@vascongado.usa> wrote in message > news:4638a11e$0$31833$a82e2bb9@reader.athenanews.c om... > > Chances are good that your bad universal joint caused the bushing damage. > > If you still have the vibration, then you probably have something else > > going > > on other than the bushing, unless the play you are describing is extreme. > > I > > can't picture punching inward on the bushing to relieve the pressure, > > because the transmission output shaft is still there to get in the way. > > Installing the new bushing is going to present the same sort of problem. > > The best bet is to wait for the shop manual, but many times the extension > > housing, the part that the bushing is in, can be removed with the > > transmission still in the car. Draining the transmission is probably a > > good > > idea first, but the shop manual will discuss that. > > > > Earle > > > > "Gerald K4NHN" <gcromer@usit.net> wrote in message > > news:O81_h.2874$296.1087@newsread4.news.pas.earthl ink.net... > >> Hi Earl > >> It where the rear drive shaft come out of the transmission. It's a 2 WD.. > > I > >> can feel the play in the yoke by moving it up and down and right and > >> left. > > A > >> friend has the same Jeep and I can't move it at all.. > >> > >> I have a vibration that I can't find when I let off the gas with no load > > on > >> the drive train. In the 50 to 75 mph range and I can hear it when it does > >> it.. I've replace the front u-joint. It was bad on one plane and good in > > the > >> other. The yoke didn't look bad, but I didn't put a mic on it... so..... > > The > >> SUV has 275K mostly road miles on it.... > >> > >> I've been told that the bushing can be gotten out with out removing the > > rear > >> housing. I'm waiting on the real shop manual to come in to see what it > > says. > >> I was told that it can be punched inward and it will slide out. Also that > >> there was a grove that a small punch will go between the housing and the > >> bushing to force the bushing inward to relieve the pressure so it will > > come > >> out... It's best to try and find out for sure before I start this... > >> > >> > >> "Earle Horton" <earle@vascongado.usa> wrote in message > >> news:46380bf2$0$31804$a82e2bb9@reader.athenanews.c om... > >> > "Gerald K4NHN" <gcromer@usit.net> wrote in message > >> > news:oMTZh.6034$Ut6.409@newsread1.news.pas.earthli nk.net... > >> >> Has anyone replaced the tail shaft bushing in a 96 Jeep GC.. Is > >> >> it hard to do in the car. > >> >> Any special tools needed.. > >> >> > >> > > >> > You mean the "transfer case tail shaft bushing"? You would have to > >> > take > >> > the > >> > tail shaft housing off, press the old bushing out, and press the new > >> > bushing > >> > in. How do you know, why do you think, it is bad? If it is, the rear > >> > drive > >> > shaft front yoke probably is too. > >> > > >> > Earle > >> > > >> > > >> > >> > > > > > > |
Re: Tail shaft bushing
> Re: Tail shaft bushing This subject title should be changed somehow, before everyone gets reported for using foul language. |
Re: Tail shaft bushing
> Re: Tail shaft bushing This subject title should be changed somehow, before everyone gets reported for using foul language. |
Re: Tail shaft bushing
> Re: Tail shaft bushing This subject title should be changed somehow, before everyone gets reported for using foul language. |
Re: Tail shaft bushing
> Re: Tail shaft bushing This subject title should be changed somehow, before everyone gets reported for using foul language. |
Re: Tail shaft bushing
I thought that was what it's called...
"Satin Fairbush" <satin@trim-it-carefully.com> wrote in message news:hN6_h.155514$aG1.92326@pd7urf3no... > > >> Re: Tail shaft bushing > > > This subject title should be changed somehow, before everyone gets > reported for using foul language. > > > > > > |
Re: Tail shaft bushing
I thought that was what it's called...
"Satin Fairbush" <satin@trim-it-carefully.com> wrote in message news:hN6_h.155514$aG1.92326@pd7urf3no... > > >> Re: Tail shaft bushing > > > This subject title should be changed somehow, before everyone gets > reported for using foul language. > > > > > > |
Re: Tail shaft bushing
I thought that was what it's called...
"Satin Fairbush" <satin@trim-it-carefully.com> wrote in message news:hN6_h.155514$aG1.92326@pd7urf3no... > > >> Re: Tail shaft bushing > > > This subject title should be changed somehow, before everyone gets > reported for using foul language. > > > > > > |
Re: Tail shaft bushing
I thought that was what it's called...
"Satin Fairbush" <satin@trim-it-carefully.com> wrote in message news:hN6_h.155514$aG1.92326@pd7urf3no... > > >> Re: Tail shaft bushing > > > This subject title should be changed somehow, before everyone gets > reported for using foul language. > > > > > > |
Re: Tail shaft bushing
On Wed, 02 May 2007 20:56:26 +0000, Gerald K4NHN wrote:
> I thought that was what it's called... Hello Gerald, My post was a sort of a general one, /not/ targeted at you personally at all, and for this I apologize. You see, some folks in Usenet have their own very personal definitions for things which usually override the dictionaries, encyclopedia and thesauri of the world -- and they can change at a moment's notice. And sometimes these same folks are hobbyist abuse-reporters. My comment was intended to be naught but a humorous flippancy relating to this sad state of affairs, but alas, sometimes it does actually happen. Even in this group. Sorry for any confusion I may have caused. > > "Satin Fairbush" <satin@trim-it-carefully.com> wrote in message > news:hN6_h.155514$aG1.92326@pd7urf3no... >> >> >>> Re: Tail shaft bushing >> >> >> This subject title should be changed somehow, before everyone gets >> reported for using foul language. >> >> >> >> >> >> |
Re: Tail shaft bushing
On Wed, 02 May 2007 20:56:26 +0000, Gerald K4NHN wrote:
> I thought that was what it's called... Hello Gerald, My post was a sort of a general one, /not/ targeted at you personally at all, and for this I apologize. You see, some folks in Usenet have their own very personal definitions for things which usually override the dictionaries, encyclopedia and thesauri of the world -- and they can change at a moment's notice. And sometimes these same folks are hobbyist abuse-reporters. My comment was intended to be naught but a humorous flippancy relating to this sad state of affairs, but alas, sometimes it does actually happen. Even in this group. Sorry for any confusion I may have caused. > > "Satin Fairbush" <satin@trim-it-carefully.com> wrote in message > news:hN6_h.155514$aG1.92326@pd7urf3no... >> >> >>> Re: Tail shaft bushing >> >> >> This subject title should be changed somehow, before everyone gets >> reported for using foul language. >> >> >> >> >> >> |
Re: Tail shaft bushing
On Wed, 02 May 2007 20:56:26 +0000, Gerald K4NHN wrote:
> I thought that was what it's called... Hello Gerald, My post was a sort of a general one, /not/ targeted at you personally at all, and for this I apologize. You see, some folks in Usenet have their own very personal definitions for things which usually override the dictionaries, encyclopedia and thesauri of the world -- and they can change at a moment's notice. And sometimes these same folks are hobbyist abuse-reporters. My comment was intended to be naught but a humorous flippancy relating to this sad state of affairs, but alas, sometimes it does actually happen. Even in this group. Sorry for any confusion I may have caused. > > "Satin Fairbush" <satin@trim-it-carefully.com> wrote in message > news:hN6_h.155514$aG1.92326@pd7urf3no... >> >> >>> Re: Tail shaft bushing >> >> >> This subject title should be changed somehow, before everyone gets >> reported for using foul language. >> >> >> >> >> >> |
Re: Tail shaft bushing
On Wed, 02 May 2007 20:56:26 +0000, Gerald K4NHN wrote:
> I thought that was what it's called... Hello Gerald, My post was a sort of a general one, /not/ targeted at you personally at all, and for this I apologize. You see, some folks in Usenet have their own very personal definitions for things which usually override the dictionaries, encyclopedia and thesauri of the world -- and they can change at a moment's notice. And sometimes these same folks are hobbyist abuse-reporters. My comment was intended to be naught but a humorous flippancy relating to this sad state of affairs, but alas, sometimes it does actually happen. Even in this group. Sorry for any confusion I may have caused. > > "Satin Fairbush" <satin@trim-it-carefully.com> wrote in message > news:hN6_h.155514$aG1.92326@pd7urf3no... >> >> >>> Re: Tail shaft bushing >> >> >> This subject title should be changed somehow, before everyone gets >> reported for using foul language. >> >> >> >> >> >> |
Re: Tail shaft bushing
No offense taken. Us "ole folks" don't know how to think like the younger
crowd.. Don't know it that's good or bad. "Satin Fairbush" <satin@trim-it-carefully.com> wrote in message news:YJ7_h.155656$aG1.15893@pd7urf3no... > On Wed, 02 May 2007 20:56:26 +0000, Gerald K4NHN wrote: > >> I thought that was what it's called... > > Hello Gerald, > > My post was a sort of a general one, /not/ targeted at you personally at > all, and for this I apologize. > > You see, some folks in Usenet have their own very personal definitions for > things which usually override the dictionaries, encyclopedia and thesauri > of the world -- and they can change at a moment's notice. > > And sometimes these same folks are hobbyist abuse-reporters. > > My comment was intended to be naught but a humorous flippancy relating to > this sad state of affairs, but alas, sometimes it does actually happen. > > Even in this group. > > Sorry for any confusion I may have caused. > > > >> >> "Satin Fairbush" <satin@trim-it-carefully.com> wrote in message >> news:hN6_h.155514$aG1.92326@pd7urf3no... >>> >>> >>>> Re: Tail shaft bushing >>> >>> >>> This subject title should be changed somehow, before everyone gets >>> reported for using foul language. >>> >>> >>> >>> >>> >>> > |
Re: Tail shaft bushing
No offense taken. Us "ole folks" don't know how to think like the younger
crowd.. Don't know it that's good or bad. "Satin Fairbush" <satin@trim-it-carefully.com> wrote in message news:YJ7_h.155656$aG1.15893@pd7urf3no... > On Wed, 02 May 2007 20:56:26 +0000, Gerald K4NHN wrote: > >> I thought that was what it's called... > > Hello Gerald, > > My post was a sort of a general one, /not/ targeted at you personally at > all, and for this I apologize. > > You see, some folks in Usenet have their own very personal definitions for > things which usually override the dictionaries, encyclopedia and thesauri > of the world -- and they can change at a moment's notice. > > And sometimes these same folks are hobbyist abuse-reporters. > > My comment was intended to be naught but a humorous flippancy relating to > this sad state of affairs, but alas, sometimes it does actually happen. > > Even in this group. > > Sorry for any confusion I may have caused. > > > >> >> "Satin Fairbush" <satin@trim-it-carefully.com> wrote in message >> news:hN6_h.155514$aG1.92326@pd7urf3no... >>> >>> >>>> Re: Tail shaft bushing >>> >>> >>> This subject title should be changed somehow, before everyone gets >>> reported for using foul language. >>> >>> >>> >>> >>> >>> > |
Re: Tail shaft bushing
No offense taken. Us "ole folks" don't know how to think like the younger
crowd.. Don't know it that's good or bad. "Satin Fairbush" <satin@trim-it-carefully.com> wrote in message news:YJ7_h.155656$aG1.15893@pd7urf3no... > On Wed, 02 May 2007 20:56:26 +0000, Gerald K4NHN wrote: > >> I thought that was what it's called... > > Hello Gerald, > > My post was a sort of a general one, /not/ targeted at you personally at > all, and for this I apologize. > > You see, some folks in Usenet have their own very personal definitions for > things which usually override the dictionaries, encyclopedia and thesauri > of the world -- and they can change at a moment's notice. > > And sometimes these same folks are hobbyist abuse-reporters. > > My comment was intended to be naught but a humorous flippancy relating to > this sad state of affairs, but alas, sometimes it does actually happen. > > Even in this group. > > Sorry for any confusion I may have caused. > > > >> >> "Satin Fairbush" <satin@trim-it-carefully.com> wrote in message >> news:hN6_h.155514$aG1.92326@pd7urf3no... >>> >>> >>>> Re: Tail shaft bushing >>> >>> >>> This subject title should be changed somehow, before everyone gets >>> reported for using foul language. >>> >>> >>> >>> >>> >>> > |
Re: Tail shaft bushing
No offense taken. Us "ole folks" don't know how to think like the younger
crowd.. Don't know it that's good or bad. "Satin Fairbush" <satin@trim-it-carefully.com> wrote in message news:YJ7_h.155656$aG1.15893@pd7urf3no... > On Wed, 02 May 2007 20:56:26 +0000, Gerald K4NHN wrote: > >> I thought that was what it's called... > > Hello Gerald, > > My post was a sort of a general one, /not/ targeted at you personally at > all, and for this I apologize. > > You see, some folks in Usenet have their own very personal definitions for > things which usually override the dictionaries, encyclopedia and thesauri > of the world -- and they can change at a moment's notice. > > And sometimes these same folks are hobbyist abuse-reporters. > > My comment was intended to be naught but a humorous flippancy relating to > this sad state of affairs, but alas, sometimes it does actually happen. > > Even in this group. > > Sorry for any confusion I may have caused. > > > >> >> "Satin Fairbush" <satin@trim-it-carefully.com> wrote in message >> news:hN6_h.155514$aG1.92326@pd7urf3no... >>> >>> >>>> Re: Tail shaft bushing >>> >>> >>> This subject title should be changed somehow, before everyone gets >>> reported for using foul language. >>> >>> >>> >>> >>> >>> > |
| All times are GMT -4. The time now is 04:47 AM. |
© 2024 MH Sub I, LLC dba Internet Brands