Re: Start up after storage
And very important - when you change the oil filter fill it 1/4 to 1/2
way with new oil. It will absorb into the filter and provide oil to your engine faster. |
Re: Start up after storage
And very important - when you change the oil filter fill it 1/4 to 1/2
way with new oil. It will absorb into the filter and provide oil to your engine faster. |
Re: Start up after storage
And very important - when you change the oil filter fill it 1/4 to 1/2
way with new oil. It will absorb into the filter and provide oil to your engine faster. |
Re: Start up after storage
> I plan to change the oil first, and thought about puling the valve
> cover gaskets and pouting a quart down each side when I refill it. > Should I pull the plugs and put a _small_ amount of oil in each > cycilinder? Anything else? Don't pull any gaskets. Why make more work for yourself than necessary? Check what the oil in there looks like first. Make sure it's not ruined by water or otherwise gunked up. You'll want to change that oil anyway but if it's bad you'd want to do it before restarting it. Pull the plugs. Put a bit of oil into each cylinder through the plug hole. Leave this in there for a couple of days. Get an attachment for your drill, pull the distributor (after marking it's placement FIRST) and use the drill to rotate the engine. This will SLOWLY turn the oil pump and get all the surfaces lubricated BEFORE it's ever started. Having the surfaces lubricated this way greatly reduces the likelihood of damage. This is pretty much the same process anyone with a boat goes through when recommissioning in the spring. Which will be in about three weeks for ours. |
Re: Start up after storage
> I plan to change the oil first, and thought about puling the valve
> cover gaskets and pouting a quart down each side when I refill it. > Should I pull the plugs and put a _small_ amount of oil in each > cycilinder? Anything else? Don't pull any gaskets. Why make more work for yourself than necessary? Check what the oil in there looks like first. Make sure it's not ruined by water or otherwise gunked up. You'll want to change that oil anyway but if it's bad you'd want to do it before restarting it. Pull the plugs. Put a bit of oil into each cylinder through the plug hole. Leave this in there for a couple of days. Get an attachment for your drill, pull the distributor (after marking it's placement FIRST) and use the drill to rotate the engine. This will SLOWLY turn the oil pump and get all the surfaces lubricated BEFORE it's ever started. Having the surfaces lubricated this way greatly reduces the likelihood of damage. This is pretty much the same process anyone with a boat goes through when recommissioning in the spring. Which will be in about three weeks for ours. |
Re: Start up after storage
> I plan to change the oil first, and thought about puling the valve
> cover gaskets and pouting a quart down each side when I refill it. > Should I pull the plugs and put a _small_ amount of oil in each > cycilinder? Anything else? Don't pull any gaskets. Why make more work for yourself than necessary? Check what the oil in there looks like first. Make sure it's not ruined by water or otherwise gunked up. You'll want to change that oil anyway but if it's bad you'd want to do it before restarting it. Pull the plugs. Put a bit of oil into each cylinder through the plug hole. Leave this in there for a couple of days. Get an attachment for your drill, pull the distributor (after marking it's placement FIRST) and use the drill to rotate the engine. This will SLOWLY turn the oil pump and get all the surfaces lubricated BEFORE it's ever started. Having the surfaces lubricated this way greatly reduces the likelihood of damage. This is pretty much the same process anyone with a boat goes through when recommissioning in the spring. Which will be in about three weeks for ours. |
Re: Start up after storage
For only a year of storage, I would just start it up unless you are
really paranoid. I would NOT change the filter (or the the oil for that matter) before starting up. Check the coolant level. Put the battery on the charger for a day or so to get it fully charged and warmed up. Pulling the plugs and adding oil is a nice thought, depends on what humidity you stored it at. A must on the gulf coast, the cold weather in the frozen north seems to put rust in hibernation like the rest of things. The carb will be dry, it will take a fair amount of cranking before it starts, this will bring oil up into the mains and rods. Let it run for 20 to 30 minutes, change the oil and filter. Check for leaks in the cooling system. Consider flushing and refill the coolant with new antifreeze. 83 CJ wrote: > Hi all, > > Been monitoring the group and had a quick question. > > I've had my CJ in storage for the past year and am getting ready to > redeploy this Spring and start it up again. Wanted to ask what the > best way to do the initial start up is. Since it hasn't run in a year > I'm assuming all the oil is down in the pan. > > I plan to change the oil first, and thought about puling the valve > cover gaskets and pouting a quart down each side when I refill it. > Should I pull the plugs and put a _small_ amount of oil in each > cycilinder? Anything else? > > Thanks. > |
Re: Start up after storage
For only a year of storage, I would just start it up unless you are
really paranoid. I would NOT change the filter (or the the oil for that matter) before starting up. Check the coolant level. Put the battery on the charger for a day or so to get it fully charged and warmed up. Pulling the plugs and adding oil is a nice thought, depends on what humidity you stored it at. A must on the gulf coast, the cold weather in the frozen north seems to put rust in hibernation like the rest of things. The carb will be dry, it will take a fair amount of cranking before it starts, this will bring oil up into the mains and rods. Let it run for 20 to 30 minutes, change the oil and filter. Check for leaks in the cooling system. Consider flushing and refill the coolant with new antifreeze. 83 CJ wrote: > Hi all, > > Been monitoring the group and had a quick question. > > I've had my CJ in storage for the past year and am getting ready to > redeploy this Spring and start it up again. Wanted to ask what the > best way to do the initial start up is. Since it hasn't run in a year > I'm assuming all the oil is down in the pan. > > I plan to change the oil first, and thought about puling the valve > cover gaskets and pouting a quart down each side when I refill it. > Should I pull the plugs and put a _small_ amount of oil in each > cycilinder? Anything else? > > Thanks. > |
Re: Start up after storage
For only a year of storage, I would just start it up unless you are
really paranoid. I would NOT change the filter (or the the oil for that matter) before starting up. Check the coolant level. Put the battery on the charger for a day or so to get it fully charged and warmed up. Pulling the plugs and adding oil is a nice thought, depends on what humidity you stored it at. A must on the gulf coast, the cold weather in the frozen north seems to put rust in hibernation like the rest of things. The carb will be dry, it will take a fair amount of cranking before it starts, this will bring oil up into the mains and rods. Let it run for 20 to 30 minutes, change the oil and filter. Check for leaks in the cooling system. Consider flushing and refill the coolant with new antifreeze. 83 CJ wrote: > Hi all, > > Been monitoring the group and had a quick question. > > I've had my CJ in storage for the past year and am getting ready to > redeploy this Spring and start it up again. Wanted to ask what the > best way to do the initial start up is. Since it hasn't run in a year > I'm assuming all the oil is down in the pan. > > I plan to change the oil first, and thought about puling the valve > cover gaskets and pouting a quart down each side when I refill it. > Should I pull the plugs and put a _small_ amount of oil in each > cycilinder? Anything else? > > Thanks. > |
Re: Start up after storage
I had a friend that had a 73 Caddy Eldorado 503ci ( I know caddy has
nothing to do with the group), it sat for 15years and when he started it, all he had to do was buy a new battery and put some new gas in it. but then once he got it out of the yard on the road, theres a different story, brake lines, tires, brake pads... "RoyJ" <spamless@microsoft.net> wrote in message news:ZZhDh.5268$Jl.2639@newsread3.news.pas.earthli nk.net... > For only a year of storage, I would just start it up unless you are really > paranoid. I would NOT change the filter (or the the oil for that matter) > before starting up. Check the coolant level. Put the battery on the > charger for a day or so to get it fully charged and warmed up. Pulling the > plugs and adding oil is a nice thought, depends on what humidity you > stored it at. A must on the gulf coast, the cold weather in the frozen > north seems to put rust in hibernation like the rest of things. > > The carb will be dry, it will take a fair amount of cranking before it > starts, this will bring oil up into the mains and rods. > > |
All times are GMT -4. The time now is 02:05 AM. |
© 2024 MH Sub I, LLC dba Internet Brands