oil pan seal for 258
I replaced the rear seal on my oil pan some time back, and I think the seal
is holding fine. I however have several leaks in the oil pan. I installed the one piece rubber gasket, and used rtv around the gasket. I am going to pull the oil pan back off and redo the gasket. My question is does the one piece rubber gasket require any rtv, or should I put it on dry? I have been researching this topic and there is very little information. |
Re: oil pan seal for 258
I put them on dry, except for the area at the rear of the pan where it seals
under the rear main. This may just be an issue with my '94 YJ, but the pan gasket tends to seep in this area unless some sealer is applied. I've used both old timey Permatex Form-A-Gasket, and RTV on this and both work fine. "Sleestak" <here@there.com> wrote in message news:109v07l9p417ec4@corp.supernews.com... > I replaced the rear seal on my oil pan some time back, and I think the seal > is holding fine. I however have several leaks in the oil pan. I installed > the one piece rubber gasket, and used rtv around the gasket. I am going to > pull the oil pan back off and redo the gasket. My question is does the one > piece rubber gasket require any rtv, or should I put it on dry? I have > been researching this topic and there is very little information. |
Re: oil pan seal for 258
I put them on dry, except for the area at the rear of the pan where it seals
under the rear main. This may just be an issue with my '94 YJ, but the pan gasket tends to seep in this area unless some sealer is applied. I've used both old timey Permatex Form-A-Gasket, and RTV on this and both work fine. "Sleestak" <here@there.com> wrote in message news:109v07l9p417ec4@corp.supernews.com... > I replaced the rear seal on my oil pan some time back, and I think the seal > is holding fine. I however have several leaks in the oil pan. I installed > the one piece rubber gasket, and used rtv around the gasket. I am going to > pull the oil pan back off and redo the gasket. My question is does the one > piece rubber gasket require any rtv, or should I put it on dry? I have > been researching this topic and there is very little information. |
Re: oil pan seal for 258
I put them on dry, except for the area at the rear of the pan where it seals
under the rear main. This may just be an issue with my '94 YJ, but the pan gasket tends to seep in this area unless some sealer is applied. I've used both old timey Permatex Form-A-Gasket, and RTV on this and both work fine. "Sleestak" <here@there.com> wrote in message news:109v07l9p417ec4@corp.supernews.com... > I replaced the rear seal on my oil pan some time back, and I think the seal > is holding fine. I however have several leaks in the oil pan. I installed > the one piece rubber gasket, and used rtv around the gasket. I am going to > pull the oil pan back off and redo the gasket. My question is does the one > piece rubber gasket require any rtv, or should I put it on dry? I have > been researching this topic and there is very little information. |
Re: oil pan seal for 258
I put them on dry, except for the area at the rear of the pan where it seals
under the rear main. This may just be an issue with my '94 YJ, but the pan gasket tends to seep in this area unless some sealer is applied. I've used both old timey Permatex Form-A-Gasket, and RTV on this and both work fine. "Sleestak" <here@there.com> wrote in message news:109v07l9p417ec4@corp.supernews.com... > I replaced the rear seal on my oil pan some time back, and I think the seal > is holding fine. I however have several leaks in the oil pan. I installed > the one piece rubber gasket, and used rtv around the gasket. I am going to > pull the oil pan back off and redo the gasket. My question is does the one > piece rubber gasket require any rtv, or should I put it on dry? I have > been researching this topic and there is very little information. |
Re: oil pan seal for 258
I would put it on dry, but that means dry. If there's an oily film on
either part the RTV will not seal properly or for long if it does. I use that brake cleaner in an aerasol can and a clean rag plus blow them off with the air hose. make sure they are absolutely free of any oil film. Steve G. "Sleestak" <here@there.com> wrote in message news:109v07l9p417ec4@corp.supernews.com... > I replaced the rear seal on my oil pan some time back, and I think the seal > is holding fine. I however have several leaks in the oil pan. I installed > the one piece rubber gasket, and used rtv around the gasket. I am going to > pull the oil pan back off and redo the gasket. My question is does the one > piece rubber gasket require any rtv, or should I put it on dry? I have > been researching this topic and there is very little information. |
Re: oil pan seal for 258
I would put it on dry, but that means dry. If there's an oily film on
either part the RTV will not seal properly or for long if it does. I use that brake cleaner in an aerasol can and a clean rag plus blow them off with the air hose. make sure they are absolutely free of any oil film. Steve G. "Sleestak" <here@there.com> wrote in message news:109v07l9p417ec4@corp.supernews.com... > I replaced the rear seal on my oil pan some time back, and I think the seal > is holding fine. I however have several leaks in the oil pan. I installed > the one piece rubber gasket, and used rtv around the gasket. I am going to > pull the oil pan back off and redo the gasket. My question is does the one > piece rubber gasket require any rtv, or should I put it on dry? I have > been researching this topic and there is very little information. |
Re: oil pan seal for 258
I would put it on dry, but that means dry. If there's an oily film on
either part the RTV will not seal properly or for long if it does. I use that brake cleaner in an aerasol can and a clean rag plus blow them off with the air hose. make sure they are absolutely free of any oil film. Steve G. "Sleestak" <here@there.com> wrote in message news:109v07l9p417ec4@corp.supernews.com... > I replaced the rear seal on my oil pan some time back, and I think the seal > is holding fine. I however have several leaks in the oil pan. I installed > the one piece rubber gasket, and used rtv around the gasket. I am going to > pull the oil pan back off and redo the gasket. My question is does the one > piece rubber gasket require any rtv, or should I put it on dry? I have > been researching this topic and there is very little information. |
Re: oil pan seal for 258
I would put it on dry, but that means dry. If there's an oily film on
either part the RTV will not seal properly or for long if it does. I use that brake cleaner in an aerasol can and a clean rag plus blow them off with the air hose. make sure they are absolutely free of any oil film. Steve G. "Sleestak" <here@there.com> wrote in message news:109v07l9p417ec4@corp.supernews.com... > I replaced the rear seal on my oil pan some time back, and I think the seal > is holding fine. I however have several leaks in the oil pan. I installed > the one piece rubber gasket, and used rtv around the gasket. I am going to > pull the oil pan back off and redo the gasket. My question is does the one > piece rubber gasket require any rtv, or should I put it on dry? I have > been researching this topic and there is very little information. |
Re: oil pan seal for 258
Steve G wrote:
Thanks, for the tips Steve. I'll let you all know how it goes. I sure hope it seals this time, because I don't want to have to take the oil pan off again :) > I would put it on dry, but that means dry. If there's an oily film on > either part the RTV will not seal properly or for long if it does. I use > that brake cleaner in an aerasol can and a clean rag plus blow them off > with > the air hose. make sure they are absolutely free of any oil film. > Steve G. > "Sleestak" <here@there.com> wrote in message > news:109v07l9p417ec4@corp.supernews.com... >> I replaced the rear seal on my oil pan some time back, and I think the > seal >> is holding fine. I however have several leaks in the oil pan. I > installed >> the one piece rubber gasket, and used rtv around the gasket. I am going > to >> pull the oil pan back off and redo the gasket. My question is does the > one >> piece rubber gasket require any rtv, or should I put it on dry? I have >> been researching this topic and there is very little information. -- Say NO! To TCPA! http://www.againsttcpa.com What's Microsoft up to: http://www.euronet.nl/users/frankvw/IhateMS.html |
All times are GMT -4. The time now is 07:48 AM. |
© 2024 MH Sub I, LLC dba Internet Brands