Re: Lift kit and front drive line angle
Dan,
I've had this kit on my '94YJ, although I have a D44 in front, D60 rear and an Atlas II. I have CVs front & rear at the t-case. If you're retaining the stock YJ D30 in front you may not have any driveline issues, however you'll definitiely have caster problems from the kits 5" shackles (1" longer than stock). To correct my front caster I needed an additional 2 degrees. (The kit came with four crap Pro Comp 2 1/2 degree aluminum shims which I tossed.) I had the rear spring pads cut loose and rewelded with the pinion centered to the T-case. In front I added steel shims from Poison Spyder Customs. They've been on there two years and have held up fine. FWIW, if you don't dial in the front caster it will be all over the road. "Dan" <dan@guy.com> wrote in message news:n44wc.669199$oR5.163389@pd7tw3no... > I am installing a RE 4.5" Lift kit in my YJ. I am not putting the > t-case lower bits and will be installing a SYE/CV shaft on the rear. > > If I leave the t-case at it's normal height, do I still need to add > shims to the front? > > -Dan |
Re: Lift kit and front drive line angle
Dan,
I've had this kit on my '94YJ, although I have a D44 in front, D60 rear and an Atlas II. I have CVs front & rear at the t-case. If you're retaining the stock YJ D30 in front you may not have any driveline issues, however you'll definitiely have caster problems from the kits 5" shackles (1" longer than stock). To correct my front caster I needed an additional 2 degrees. (The kit came with four crap Pro Comp 2 1/2 degree aluminum shims which I tossed.) I had the rear spring pads cut loose and rewelded with the pinion centered to the T-case. In front I added steel shims from Poison Spyder Customs. They've been on there two years and have held up fine. FWIW, if you don't dial in the front caster it will be all over the road. "Dan" <dan@guy.com> wrote in message news:n44wc.669199$oR5.163389@pd7tw3no... > I am installing a RE 4.5" Lift kit in my YJ. I am not putting the > t-case lower bits and will be installing a SYE/CV shaft on the rear. > > If I leave the t-case at it's normal height, do I still need to add > shims to the front? > > -Dan |
Re: Lift kit and front drive line angle
Dan,
I've had this kit on my '94YJ, although I have a D44 in front, D60 rear and an Atlas II. I have CVs front & rear at the t-case. If you're retaining the stock YJ D30 in front you may not have any driveline issues, however you'll definitiely have caster problems from the kits 5" shackles (1" longer than stock). To correct my front caster I needed an additional 2 degrees. (The kit came with four crap Pro Comp 2 1/2 degree aluminum shims which I tossed.) I had the rear spring pads cut loose and rewelded with the pinion centered to the T-case. In front I added steel shims from Poison Spyder Customs. They've been on there two years and have held up fine. FWIW, if you don't dial in the front caster it will be all over the road. "Dan" <dan@guy.com> wrote in message news:n44wc.669199$oR5.163389@pd7tw3no... > I am installing a RE 4.5" Lift kit in my YJ. I am not putting the > t-case lower bits and will be installing a SYE/CV shaft on the rear. > > If I leave the t-case at it's normal height, do I still need to add > shims to the front? > > -Dan |
Re: Lift kit and front drive line angle
Yes, the shims keep the front wheel alignment correct. The YJ already
has a CV or double cardan joint on the driveshaft, so only the rear needs one. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Dan wrote: > > I am installing a RE 4.5" Lift kit in my YJ. I am not putting the > t-case lower bits and will be installing a SYE/CV shaft on the rear. > > If I leave the t-case at it's normal height, do I still need to add > shims to the front? > > -Dan |
Re: Lift kit and front drive line angle
Yes, the shims keep the front wheel alignment correct. The YJ already
has a CV or double cardan joint on the driveshaft, so only the rear needs one. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Dan wrote: > > I am installing a RE 4.5" Lift kit in my YJ. I am not putting the > t-case lower bits and will be installing a SYE/CV shaft on the rear. > > If I leave the t-case at it's normal height, do I still need to add > shims to the front? > > -Dan |
Re: Lift kit and front drive line angle
Yes, the shims keep the front wheel alignment correct. The YJ already
has a CV or double cardan joint on the driveshaft, so only the rear needs one. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Dan wrote: > > I am installing a RE 4.5" Lift kit in my YJ. I am not putting the > t-case lower bits and will be installing a SYE/CV shaft on the rear. > > If I leave the t-case at it's normal height, do I still need to add > shims to the front? > > -Dan |
Re: Lift kit and front drive line angle
Yes, the shims keep the front wheel alignment correct. The YJ already
has a CV or double cardan joint on the driveshaft, so only the rear needs one. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Dan wrote: > > I am installing a RE 4.5" Lift kit in my YJ. I am not putting the > t-case lower bits and will be installing a SYE/CV shaft on the rear. > > If I leave the t-case at it's normal height, do I still need to add > shims to the front? > > -Dan |
All times are GMT -4. The time now is 06:49 PM. |
© 2024 MH Sub I, LLC dba Internet Brands