Help w/ Installng Turn Signal in GC
 

My daughter cracked the front pass turn signal lens on her '94 GC. I have a
new lens assy and see that it is install w/ a screw on top and screw on the
bottom. I've located the screw on top but access to the bottom of the assy
is a real trick.

Any insight as to removing the old turn signal lens? Thx

Chip L

Re: Help w/ Installng Turn Signal in GC
 

Chip L did pass the time by typing:
> My daughter cracked the front pass turn signal lens on her '94 GC. I have a
> new lens assy and see that it is install w/ a screw on top and screw on the
> bottom. I've located the screw on top but access to the bottom of the assy
> is a real trick.
>
> Any insight as to removing the old turn signal lens? Thx

Take the thinest phillips you have and wedge it between the upper turn
signal and the lower one, about 1/2" away from the edge by the headlamp.
With a flashlight you can see it better. You will push the lower signal
down a bit, but that's the way it's done.

When you put the new unit in, put your screwdriver on the lower screw
then set the lamp in and tighen the lower screw. Then put the side one in.


--
-- DougW -- 93 ZJ 4.0 http://members.cox.net/wilsond
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!

Re: Help w/ Installng Turn Signal in GC
 

Chip L did pass the time by typing:
> My daughter cracked the front pass turn signal lens on her '94 GC. I have a
> new lens assy and see that it is install w/ a screw on top and screw on the
> bottom. I've located the screw on top but access to the bottom of the assy
> is a real trick.
>
> Any insight as to removing the old turn signal lens? Thx

Take the thinest phillips you have and wedge it between the upper turn
signal and the lower one, about 1/2" away from the edge by the headlamp.
With a flashlight you can see it better. You will push the lower signal
down a bit, but that's the way it's done.

When you put the new unit in, put your screwdriver on the lower screw
then set the lamp in and tighen the lower screw. Then put the side one in.


--
-- DougW -- 93 ZJ 4.0 http://members.cox.net/wilsond
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!

Re: Help w/ Installng Turn Signal in GC
 

Chip L did pass the time by typing:
> My daughter cracked the front pass turn signal lens on her '94 GC. I have a
> new lens assy and see that it is install w/ a screw on top and screw on the
> bottom. I've located the screw on top but access to the bottom of the assy
> is a real trick.
>
> Any insight as to removing the old turn signal lens? Thx

Take the thinest phillips you have and wedge it between the upper turn
signal and the lower one, about 1/2" away from the edge by the headlamp.
With a flashlight you can see it better. You will push the lower signal
down a bit, but that's the way it's done.

When you put the new unit in, put your screwdriver on the lower screw
then set the lamp in and tighen the lower screw. Then put the side one in.


--
-- DougW -- 93 ZJ 4.0 http://members.cox.net/wilsond
HESCO Supercharger - 300W IASCA Stereo - Edelbrock IAS Shocks
Gibson Exhaust - rear DCpower - custom gauge install - Stillen Rotors
Banks Header - and BEER, in the fridge!

Re: Help w/ Installng Turn Signal in GC
 

a long skinny phillips screw driver

Chip L wrote:

> My daughter cracked the front pass turn signal lens on her '94 GC. I have a
> new lens assy and see that it is install w/ a screw on top and screw on the
> bottom. I've located the screw on top but access to the bottom of the assy
> is a real trick.
>
> Any insight as to removing the old turn signal lens? Thx
>
> Chip L

Re: Help w/ Installng Turn Signal in GC
 

a long skinny phillips screw driver

Chip L wrote:

> My daughter cracked the front pass turn signal lens on her '94 GC. I have a
> new lens assy and see that it is install w/ a screw on top and screw on the
> bottom. I've located the screw on top but access to the bottom of the assy
> is a real trick.
>
> Any insight as to removing the old turn signal lens? Thx
>
> Chip L

Re: Help w/ Installng Turn Signal in GC
 

a long skinny phillips screw driver

Chip L wrote:

> My daughter cracked the front pass turn signal lens on her '94 GC. I have a
> new lens assy and see that it is install w/ a screw on top and screw on the
> bottom. I've located the screw on top but access to the bottom of the assy
> is a real trick.
>
> Any insight as to removing the old turn signal lens? Thx
>
> Chip L