Dana 44 bearing questions
 

I say a site a while back (I think Bill may have posted a link to it)
the explained how to replace the bearings with out a press. Does any
one know where I can find those instructions?

How much end play is acceptable on a Dana 44 after the bearing has been
replaced?

-Dan

Re: Dana 44 bearing questions
 

http://www.off-road.com/dodge/ramcha...ld_Article.htm


"George" <george@noexist.com> a écrit dans le message de news:
DE0Ed.23526$Xk.6616@pd7tw3no...
>I say a site a while back (I think Bill may have posted a link to it) the
>explained how to replace the bearings with out a press. Does any one know
>where I can find those instructions?
>
> How much end play is acceptable on a Dana 44 after the bearing has been
> replaced?
>
> -Dan

Re: Dana 44 bearing questions
 

http://www.off-road.com/dodge/ramcha...ld_Article.htm


"George" <george@noexist.com> a écrit dans le message de news:
DE0Ed.23526$Xk.6616@pd7tw3no...
>I say a site a while back (I think Bill may have posted a link to it) the
>explained how to replace the bearings with out a press. Does any one know
>where I can find those instructions?
>
> How much end play is acceptable on a Dana 44 after the bearing has been
> replaced?
>
> -Dan

Re: Dana 44 bearing questions
 

http://www.off-road.com/dodge/ramcha...ld_Article.htm


"George" <george@noexist.com> a écrit dans le message de news:
DE0Ed.23526$Xk.6616@pd7tw3no...
>I say a site a while back (I think Bill may have posted a link to it) the
>explained how to replace the bearings with out a press. Does any one know
>where I can find those instructions?
>
> How much end play is acceptable on a Dana 44 after the bearing has been
> replaced?
>
> -Dan

Re: Dana 44 bearing questions
 

Hi Dan,
By mentioning press, must mean you're talking about the Dana 44 rear
end, which will need a press to push the retaining ring back into place.
The semi floater will feel loose, but there is no setup to it:
http://www.----------.com/03TJrearWbearing.pdf
God Bless America, ßill O|||||||O
mailto:--------------------

George wrote:
>
> I say a site a while back (I think Bill may have posted a link to it)
> the explained how to replace the bearings with out a press. Does any
> one know where I can find those instructions?
>
> How much end play is acceptable on a Dana 44 after the bearing has been
> replaced?
>
> -Dan

Re: Dana 44 bearing questions
 

Hi Dan,
By mentioning press, must mean you're talking about the Dana 44 rear
end, which will need a press to push the retaining ring back into place.
The semi floater will feel loose, but there is no setup to it:
http://www.----------.com/03TJrearWbearing.pdf
God Bless America, ßill O|||||||O
mailto:--------------------

George wrote:
>
> I say a site a while back (I think Bill may have posted a link to it)
> the explained how to replace the bearings with out a press. Does any
> one know where I can find those instructions?
>
> How much end play is acceptable on a Dana 44 after the bearing has been
> replaced?
>
> -Dan

Re: Dana 44 bearing questions
 

Hi Dan,
By mentioning press, must mean you're talking about the Dana 44 rear
end, which will need a press to push the retaining ring back into place.
The semi floater will feel loose, but there is no setup to it:
http://www.----------.com/03TJrearWbearing.pdf
God Bless America, ßill O|||||||O
mailto:--------------------

George wrote:
>
> I say a site a while back (I think Bill may have posted a link to it)
> the explained how to replace the bearings with out a press. Does any
> one know where I can find those instructions?
>
> How much end play is acceptable on a Dana 44 after the bearing has been
> replaced?
>
> -Dan

Re: Dana 44 bearing questions
 

Yes, I am refering to the Dana 44 rear.

If I don't have a large hydraulic press, how would I put the new bearing
and retaining ring back on the axle?

-Dan

L.W.(ßill) ------ III wrote:

> Hi Dan,
> By mentioning press, must mean you're talking about the Dana 44 rear
> end, which will need a press to push the retaining ring back into place.
> The semi floater will feel loose, but there is no setup to it:
> http://www.----------.com/03TJrearWbearing.pdf
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> George wrote:
>
>>I say a site a while back (I think Bill may have posted a link to it)
>>the explained how to replace the bearings with out a press. Does any
>>one know where I can find those instructions?
>>
>>How much end play is acceptable on a Dana 44 after the bearing has been
>>replaced?
>>
>> -Dan

Re: Dana 44 bearing questions
 

Yes, I am refering to the Dana 44 rear.

If I don't have a large hydraulic press, how would I put the new bearing
and retaining ring back on the axle?

-Dan

L.W.(ßill) ------ III wrote:

> Hi Dan,
> By mentioning press, must mean you're talking about the Dana 44 rear
> end, which will need a press to push the retaining ring back into place.
> The semi floater will feel loose, but there is no setup to it:
> http://www.----------.com/03TJrearWbearing.pdf
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> George wrote:
>
>>I say a site a while back (I think Bill may have posted a link to it)
>>the explained how to replace the bearings with out a press. Does any
>>one know where I can find those instructions?
>>
>>How much end play is acceptable on a Dana 44 after the bearing has been
>>replaced?
>>
>> -Dan

Re: Dana 44 bearing questions
 

Yes, I am refering to the Dana 44 rear.

If I don't have a large hydraulic press, how would I put the new bearing
and retaining ring back on the axle?

-Dan

L.W.(ßill) ------ III wrote:

> Hi Dan,
> By mentioning press, must mean you're talking about the Dana 44 rear
> end, which will need a press to push the retaining ring back into place.
> The semi floater will feel loose, but there is no setup to it:
> http://www.----------.com/03TJrearWbearing.pdf
> God Bless America, ßill O|||||||O
> mailto:--------------------
>
> George wrote:
>
>>I say a site a while back (I think Bill may have posted a link to it)
>>the explained how to replace the bearings with out a press. Does any
>>one know where I can find those instructions?
>>
>>How much end play is acceptable on a Dana 44 after the bearing has been
>>replaced?
>>
>> -Dan