That's pretty challenging without removing the center console. I don't
know how to do that yet... but I will....

 

That's pretty challenging without removing the center console. I don't
know how to do that yet... but I will....

 

That's pretty challenging without removing the center console. I don't
know how to do that yet... but I will....

 

I believe you will have to lift up on the handle lever before you try
pushing in on that bar. That bar will be held solid by the pressure on
the cables.

Other than that you can go under and 'try' to take apart the cable setup
connection just in front of the back wheels. 'If' you can loosen it, it
would make it easier to pull up on the handle to push that rod in. That
cable adjustment is usually rusted up solid though. It is only used
when installing new cables so it seizes up.

Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)

flydog wrote:
>
> This evening the release button and the spring underneath it popped off
> the end of the emergency brake lever. Problem is, it popped off as I
> was setting the brake. Now, I don't have a way to release the brake!
>
> The brake is set and I am more-or-less stuck. Fortunately, it happened
> at the top of the driveway. My question: is there a way to release the
> emergency brake without using the brake lever? As I look into the space
> where the button should be located, I see a metal rod, but it is flush
> inside the housing where the button used to be located. I did try
> pressing the rod with the tip of a screwdriver, but it does not move.
>
> Any suggestions would be most appreciated.

 

I believe you will have to lift up on the handle lever before you try
pushing in on that bar. That bar will be held solid by the pressure on
the cables.

Other than that you can go under and 'try' to take apart the cable setup
connection just in front of the back wheels. 'If' you can loosen it, it
would make it easier to pull up on the handle to push that rod in. That
cable adjustment is usually rusted up solid though. It is only used
when installing new cables so it seizes up.

Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)

flydog wrote:
>
> This evening the release button and the spring underneath it popped off
> the end of the emergency brake lever. Problem is, it popped off as I
> was setting the brake. Now, I don't have a way to release the brake!
>
> The brake is set and I am more-or-less stuck. Fortunately, it happened
> at the top of the driveway. My question: is there a way to release the
> emergency brake without using the brake lever? As I look into the space
> where the button should be located, I see a metal rod, but it is flush
> inside the housing where the button used to be located. I did try
> pressing the rod with the tip of a screwdriver, but it does not move.
>
> Any suggestions would be most appreciated.

 

I believe you will have to lift up on the handle lever before you try
pushing in on that bar. That bar will be held solid by the pressure on
the cables.

Other than that you can go under and 'try' to take apart the cable setup
connection just in front of the back wheels. 'If' you can loosen it, it
would make it easier to pull up on the handle to push that rod in. That
cable adjustment is usually rusted up solid though. It is only used
when installing new cables so it seizes up.

Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)

flydog wrote:
>
> This evening the release button and the spring underneath it popped off
> the end of the emergency brake lever. Problem is, it popped off as I
> was setting the brake. Now, I don't have a way to release the brake!
>
> The brake is set and I am more-or-less stuck. Fortunately, it happened
> at the top of the driveway. My question: is there a way to release the
> emergency brake without using the brake lever? As I look into the space
> where the button should be located, I see a metal rod, but it is flush
> inside the housing where the button used to be located. I did try
> pressing the rod with the tip of a screwdriver, but it does not move.
>
> Any suggestions would be most appreciated.

 

Send me an e-mail for an e-address that can receive attachments and remind
me what info you are looking for.. (remember to remove the SPAM)


"flydog" <marvinguard-groups@yahoo.com> wrote in message
news:1145624974.604330.292040@i40g2000cwc.googlegr oups.com...
> That's pretty challenging without removing the center console. I don't
> know how to do that yet... but I will....
>

 

Send me an e-mail for an e-address that can receive attachments and remind
me what info you are looking for.. (remember to remove the SPAM)


"flydog" <marvinguard-groups@yahoo.com> wrote in message
news:1145624974.604330.292040@i40g2000cwc.googlegr oups.com...
> That's pretty challenging without removing the center console. I don't
> know how to do that yet... but I will....
>

 

Send me an e-mail for an e-address that can receive attachments and remind
me what info you are looking for.. (remember to remove the SPAM)


"flydog" <marvinguard-groups@yahoo.com> wrote in message
news:1145624974.604330.292040@i40g2000cwc.googlegr oups.com...
> That's pretty challenging without removing the center console. I don't
> know how to do that yet... but I will....
>

 

I was able to back the nut off and relieve the tension. The car now is
drivable. Next job is to replace the lever.