1989 Cherokee Won't Shift Into 2nd After Wash
Guest
Posts: n/a
1989 Cherokee Won't Shift Into 2nd After Wash
I had my 1989 Cherokee 4.0L engine washed. Afterwards, the Cherokee
wouldn't shift into 2nd. It just goes in 1st gear and Reverse. I did
uncouple and re-attached as many electrical attachments that I could
get to on top of the engine, along the firewall, and by the relay. I
got it to go into 2nd once, but then it reverted back to just 1st and I
haven't got it to work right since. I assume something's not making
good contact or is failing, but I don't know what. I've read about the
Throttle Position Sensor and a kickdown cable, but don't know what I'm
looking for. Any ideas?
wouldn't shift into 2nd. It just goes in 1st gear and Reverse. I did
uncouple and re-attached as many electrical attachments that I could
get to on top of the engine, along the firewall, and by the relay. I
got it to go into 2nd once, but then it reverted back to just 1st and I
haven't got it to work right since. I assume something's not making
good contact or is failing, but I don't know what. I've read about the
Throttle Position Sensor and a kickdown cable, but don't know what I'm
looking for. Any ideas?
Guest
Posts: n/a
Re: 1989 Cherokee Won't Shift Into 2nd After Wash
I would recommend you pull all the plugs on the throttle body open and
spray them out with WD40 which is a great non conductive Water
Displacement fluid. Any other's suspected of getting wet also.
The TPS controls the shift points. If spraying up top doesn't do it,
there are plugs down near the tranny too.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
Mickey wrote:
>
> I had my 1989 Cherokee 4.0L engine washed. Afterwards, the Cherokee
> wouldn't shift into 2nd. It just goes in 1st gear and Reverse. I did
> uncouple and re-attached as many electrical attachments that I could
> get to on top of the engine, along the firewall, and by the relay. I
> got it to go into 2nd once, but then it reverted back to just 1st and I
> haven't got it to work right since. I assume something's not making
> good contact or is failing, but I don't know what. I've read about the
> Throttle Position Sensor and a kickdown cable, but don't know what I'm
> looking for. Any ideas?
spray them out with WD40 which is a great non conductive Water
Displacement fluid. Any other's suspected of getting wet also.
The TPS controls the shift points. If spraying up top doesn't do it,
there are plugs down near the tranny too.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
Mickey wrote:
>
> I had my 1989 Cherokee 4.0L engine washed. Afterwards, the Cherokee
> wouldn't shift into 2nd. It just goes in 1st gear and Reverse. I did
> uncouple and re-attached as many electrical attachments that I could
> get to on top of the engine, along the firewall, and by the relay. I
> got it to go into 2nd once, but then it reverted back to just 1st and I
> haven't got it to work right since. I assume something's not making
> good contact or is failing, but I don't know what. I've read about the
> Throttle Position Sensor and a kickdown cable, but don't know what I'm
> looking for. Any ideas?
Guest
Posts: n/a
Re: 1989 Cherokee Won't Shift Into 2nd After Wash
I would recommend you pull all the plugs on the throttle body open and
spray them out with WD40 which is a great non conductive Water
Displacement fluid. Any other's suspected of getting wet also.
The TPS controls the shift points. If spraying up top doesn't do it,
there are plugs down near the tranny too.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
Mickey wrote:
>
> I had my 1989 Cherokee 4.0L engine washed. Afterwards, the Cherokee
> wouldn't shift into 2nd. It just goes in 1st gear and Reverse. I did
> uncouple and re-attached as many electrical attachments that I could
> get to on top of the engine, along the firewall, and by the relay. I
> got it to go into 2nd once, but then it reverted back to just 1st and I
> haven't got it to work right since. I assume something's not making
> good contact or is failing, but I don't know what. I've read about the
> Throttle Position Sensor and a kickdown cable, but don't know what I'm
> looking for. Any ideas?
spray them out with WD40 which is a great non conductive Water
Displacement fluid. Any other's suspected of getting wet also.
The TPS controls the shift points. If spraying up top doesn't do it,
there are plugs down near the tranny too.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
Mickey wrote:
>
> I had my 1989 Cherokee 4.0L engine washed. Afterwards, the Cherokee
> wouldn't shift into 2nd. It just goes in 1st gear and Reverse. I did
> uncouple and re-attached as many electrical attachments that I could
> get to on top of the engine, along the firewall, and by the relay. I
> got it to go into 2nd once, but then it reverted back to just 1st and I
> haven't got it to work right since. I assume something's not making
> good contact or is failing, but I don't know what. I've read about the
> Throttle Position Sensor and a kickdown cable, but don't know what I'm
> looking for. Any ideas?
Guest
Posts: n/a
Re: 1989 Cherokee Won't Shift Into 2nd After Wash
I would recommend you pull all the plugs on the throttle body open and
spray them out with WD40 which is a great non conductive Water
Displacement fluid. Any other's suspected of getting wet also.
The TPS controls the shift points. If spraying up top doesn't do it,
there are plugs down near the tranny too.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
Mickey wrote:
>
> I had my 1989 Cherokee 4.0L engine washed. Afterwards, the Cherokee
> wouldn't shift into 2nd. It just goes in 1st gear and Reverse. I did
> uncouple and re-attached as many electrical attachments that I could
> get to on top of the engine, along the firewall, and by the relay. I
> got it to go into 2nd once, but then it reverted back to just 1st and I
> haven't got it to work right since. I assume something's not making
> good contact or is failing, but I don't know what. I've read about the
> Throttle Position Sensor and a kickdown cable, but don't know what I'm
> looking for. Any ideas?
spray them out with WD40 which is a great non conductive Water
Displacement fluid. Any other's suspected of getting wet also.
The TPS controls the shift points. If spraying up top doesn't do it,
there are plugs down near the tranny too.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
Mickey wrote:
>
> I had my 1989 Cherokee 4.0L engine washed. Afterwards, the Cherokee
> wouldn't shift into 2nd. It just goes in 1st gear and Reverse. I did
> uncouple and re-attached as many electrical attachments that I could
> get to on top of the engine, along the firewall, and by the relay. I
> got it to go into 2nd once, but then it reverted back to just 1st and I
> haven't got it to work right since. I assume something's not making
> good contact or is failing, but I don't know what. I've read about the
> Throttle Position Sensor and a kickdown cable, but don't know what I'm
> looking for. Any ideas?
Guest
Posts: n/a
Re: 1989 Cherokee Won't Shift Into 2nd After Wash
I would recommend you pull all the plugs on the throttle body open and
spray them out with WD40 which is a great non conductive Water
Displacement fluid. Any other's suspected of getting wet also.
The TPS controls the shift points. If spraying up top doesn't do it,
there are plugs down near the tranny too.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
Mickey wrote:
>
> I had my 1989 Cherokee 4.0L engine washed. Afterwards, the Cherokee
> wouldn't shift into 2nd. It just goes in 1st gear and Reverse. I did
> uncouple and re-attached as many electrical attachments that I could
> get to on top of the engine, along the firewall, and by the relay. I
> got it to go into 2nd once, but then it reverted back to just 1st and I
> haven't got it to work right since. I assume something's not making
> good contact or is failing, but I don't know what. I've read about the
> Throttle Position Sensor and a kickdown cable, but don't know what I'm
> looking for. Any ideas?
spray them out with WD40 which is a great non conductive Water
Displacement fluid. Any other's suspected of getting wet also.
The TPS controls the shift points. If spraying up top doesn't do it,
there are plugs down near the tranny too.
Mike
86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00
88 Cherokee 235 BFG AT's
Canadian Off Road Trips Photos: Non members can still view!
Jan/06 http://www.imagestation.com/album/pi...?id=2115147590
(More Off Road album links at bottom of the view page)
Mickey wrote:
>
> I had my 1989 Cherokee 4.0L engine washed. Afterwards, the Cherokee
> wouldn't shift into 2nd. It just goes in 1st gear and Reverse. I did
> uncouple and re-attached as many electrical attachments that I could
> get to on top of the engine, along the firewall, and by the relay. I
> got it to go into 2nd once, but then it reverted back to just 1st and I
> haven't got it to work right since. I assume something's not making
> good contact or is failing, but I don't know what. I've read about the
> Throttle Position Sensor and a kickdown cable, but don't know what I'm
> looking for. Any ideas?
Guest
Posts: n/a
Re: 1989 Cherokee Won't Shift Into 2nd After Wash
The TPS that Mike is mentioning is most likely bad. Easy to replace but just
make sure you get the right one. The one for standard shift is different.
JoBo
"Mickey" <sheetsm42@gmail.com> wrote in message
news:1155501623.070600.55570@i42g2000cwa.googlegro ups.com...
>I had my 1989 Cherokee 4.0L engine washed. Afterwards, the Cherokee
> wouldn't shift into 2nd. It just goes in 1st gear and Reverse. I did
> uncouple and re-attached as many electrical attachments that I could
> get to on top of the engine, along the firewall, and by the relay. I
> got it to go into 2nd once, but then it reverted back to just 1st and I
> haven't got it to work right since. I assume something's not making
> good contact or is failing, but I don't know what. I've read about the
> Throttle Position Sensor and a kickdown cable, but don't know what I'm
> looking for. Any ideas?
>
make sure you get the right one. The one for standard shift is different.
JoBo
"Mickey" <sheetsm42@gmail.com> wrote in message
news:1155501623.070600.55570@i42g2000cwa.googlegro ups.com...
>I had my 1989 Cherokee 4.0L engine washed. Afterwards, the Cherokee
> wouldn't shift into 2nd. It just goes in 1st gear and Reverse. I did
> uncouple and re-attached as many electrical attachments that I could
> get to on top of the engine, along the firewall, and by the relay. I
> got it to go into 2nd once, but then it reverted back to just 1st and I
> haven't got it to work right since. I assume something's not making
> good contact or is failing, but I don't know what. I've read about the
> Throttle Position Sensor and a kickdown cable, but don't know what I'm
> looking for. Any ideas?
>
Guest
Posts: n/a
Re: 1989 Cherokee Won't Shift Into 2nd After Wash
The TPS that Mike is mentioning is most likely bad. Easy to replace but just
make sure you get the right one. The one for standard shift is different.
JoBo
"Mickey" <sheetsm42@gmail.com> wrote in message
news:1155501623.070600.55570@i42g2000cwa.googlegro ups.com...
>I had my 1989 Cherokee 4.0L engine washed. Afterwards, the Cherokee
> wouldn't shift into 2nd. It just goes in 1st gear and Reverse. I did
> uncouple and re-attached as many electrical attachments that I could
> get to on top of the engine, along the firewall, and by the relay. I
> got it to go into 2nd once, but then it reverted back to just 1st and I
> haven't got it to work right since. I assume something's not making
> good contact or is failing, but I don't know what. I've read about the
> Throttle Position Sensor and a kickdown cable, but don't know what I'm
> looking for. Any ideas?
>
make sure you get the right one. The one for standard shift is different.
JoBo
"Mickey" <sheetsm42@gmail.com> wrote in message
news:1155501623.070600.55570@i42g2000cwa.googlegro ups.com...
>I had my 1989 Cherokee 4.0L engine washed. Afterwards, the Cherokee
> wouldn't shift into 2nd. It just goes in 1st gear and Reverse. I did
> uncouple and re-attached as many electrical attachments that I could
> get to on top of the engine, along the firewall, and by the relay. I
> got it to go into 2nd once, but then it reverted back to just 1st and I
> haven't got it to work right since. I assume something's not making
> good contact or is failing, but I don't know what. I've read about the
> Throttle Position Sensor and a kickdown cable, but don't know what I'm
> looking for. Any ideas?
>
Guest
Posts: n/a
Re: 1989 Cherokee Won't Shift Into 2nd After Wash
The TPS that Mike is mentioning is most likely bad. Easy to replace but just
make sure you get the right one. The one for standard shift is different.
JoBo
"Mickey" <sheetsm42@gmail.com> wrote in message
news:1155501623.070600.55570@i42g2000cwa.googlegro ups.com...
>I had my 1989 Cherokee 4.0L engine washed. Afterwards, the Cherokee
> wouldn't shift into 2nd. It just goes in 1st gear and Reverse. I did
> uncouple and re-attached as many electrical attachments that I could
> get to on top of the engine, along the firewall, and by the relay. I
> got it to go into 2nd once, but then it reverted back to just 1st and I
> haven't got it to work right since. I assume something's not making
> good contact or is failing, but I don't know what. I've read about the
> Throttle Position Sensor and a kickdown cable, but don't know what I'm
> looking for. Any ideas?
>
make sure you get the right one. The one for standard shift is different.
JoBo
"Mickey" <sheetsm42@gmail.com> wrote in message
news:1155501623.070600.55570@i42g2000cwa.googlegro ups.com...
>I had my 1989 Cherokee 4.0L engine washed. Afterwards, the Cherokee
> wouldn't shift into 2nd. It just goes in 1st gear and Reverse. I did
> uncouple and re-attached as many electrical attachments that I could
> get to on top of the engine, along the firewall, and by the relay. I
> got it to go into 2nd once, but then it reverted back to just 1st and I
> haven't got it to work right since. I assume something's not making
> good contact or is failing, but I don't know what. I've read about the
> Throttle Position Sensor and a kickdown cable, but don't know what I'm
> looking for. Any ideas?
>
Guest
Posts: n/a
Re: 1989 Cherokee Won't Shift Into 2nd After Wash
The TPS that Mike is mentioning is most likely bad. Easy to replace but just
make sure you get the right one. The one for standard shift is different.
JoBo
"Mickey" <sheetsm42@gmail.com> wrote in message
news:1155501623.070600.55570@i42g2000cwa.googlegro ups.com...
>I had my 1989 Cherokee 4.0L engine washed. Afterwards, the Cherokee
> wouldn't shift into 2nd. It just goes in 1st gear and Reverse. I did
> uncouple and re-attached as many electrical attachments that I could
> get to on top of the engine, along the firewall, and by the relay. I
> got it to go into 2nd once, but then it reverted back to just 1st and I
> haven't got it to work right since. I assume something's not making
> good contact or is failing, but I don't know what. I've read about the
> Throttle Position Sensor and a kickdown cable, but don't know what I'm
> looking for. Any ideas?
>
make sure you get the right one. The one for standard shift is different.
JoBo
"Mickey" <sheetsm42@gmail.com> wrote in message
news:1155501623.070600.55570@i42g2000cwa.googlegro ups.com...
>I had my 1989 Cherokee 4.0L engine washed. Afterwards, the Cherokee
> wouldn't shift into 2nd. It just goes in 1st gear and Reverse. I did
> uncouple and re-attached as many electrical attachments that I could
> get to on top of the engine, along the firewall, and by the relay. I
> got it to go into 2nd once, but then it reverted back to just 1st and I
> haven't got it to work right since. I assume something's not making
> good contact or is failing, but I don't know what. I've read about the
> Throttle Position Sensor and a kickdown cable, but don't know what I'm
> looking for. Any ideas?
>
Thread
Thread Starter
Forum
Replies
Last Post
Chip L
Jeep Mailing List
24
Aug 10, 2007 10:54 PM
breton
Jeep Mailing List
15
Dec 28, 2006 09:51 AM
New Old Jeep Owner
Jeep Mailing List
16
Aug 1, 2006 08:02 PM
tom
Jeep Mailing List
44
Jul 26, 2006 08:33 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)