*How to for a U Joint.....*
Hi, changing a front end u joint the right side. 1st time doing this. Before
i go ahead start this weekend thought I would ask if anyone has a good "How to" step by step web page or anything else? So I might make quicker,safer work of this task. Although I have help, I have been told if I do this wrong the results could be disastrous. :-| Any advice would be welcome and appreciated...... -Brian 91 YJ 4.0 o_o_o_o /| ,[_____], |ŻŻŻL --O|||||||O- ()_)Ż()_) ŻŻŻ )_) |
Re: *How to for a U Joint.....*
Bill H will likely chime in with a web site that is pretty through on
how to do it. Only problem is that he lives in the southwest where ice, snow, RAIN, and 10,000 salt trucks don't darken his doorstep. If you live north, the hub will be a real stinker to get loose from the steering knuckle. Lot of choices in how to get it out, mine is to jack the front end up HIGH, (use 6 ton jack stands to get it up high enough), use a BFH from directly undneath. YMMV Brian wrote: > Hi, changing a front end u joint the right side. 1st time doing this. Before > i go ahead start this weekend thought I would ask if anyone has a good "How > to" step by step web page or anything else? So I might make quicker,safer > work of this task. Although I have help, I have been told if I do this wrong > the results could be disastrous. :-| > > Any advice would be welcome and appreciated...... > > -Brian > 91 YJ 4.0 > > o_o_o_o > /| ,[_____], > |ŻŻŻL --O|||||||O- > ()_)Ż()_) ŻŻŻ )_) > > > |
Re: *How to for a U Joint.....*
Bill H will likely chime in with a web site that is pretty through on
how to do it. Only problem is that he lives in the southwest where ice, snow, RAIN, and 10,000 salt trucks don't darken his doorstep. If you live north, the hub will be a real stinker to get loose from the steering knuckle. Lot of choices in how to get it out, mine is to jack the front end up HIGH, (use 6 ton jack stands to get it up high enough), use a BFH from directly undneath. YMMV Brian wrote: > Hi, changing a front end u joint the right side. 1st time doing this. Before > i go ahead start this weekend thought I would ask if anyone has a good "How > to" step by step web page or anything else? So I might make quicker,safer > work of this task. Although I have help, I have been told if I do this wrong > the results could be disastrous. :-| > > Any advice would be welcome and appreciated...... > > -Brian > 91 YJ 4.0 > > o_o_o_o > /| ,[_____], > |ŻŻŻL --O|||||||O- > ()_)Ż()_) ŻŻŻ )_) > > > |
Re: *How to for a U Joint.....*
Bill H will likely chime in with a web site that is pretty through on
how to do it. Only problem is that he lives in the southwest where ice, snow, RAIN, and 10,000 salt trucks don't darken his doorstep. If you live north, the hub will be a real stinker to get loose from the steering knuckle. Lot of choices in how to get it out, mine is to jack the front end up HIGH, (use 6 ton jack stands to get it up high enough), use a BFH from directly undneath. YMMV Brian wrote: > Hi, changing a front end u joint the right side. 1st time doing this. Before > i go ahead start this weekend thought I would ask if anyone has a good "How > to" step by step web page or anything else? So I might make quicker,safer > work of this task. Although I have help, I have been told if I do this wrong > the results could be disastrous. :-| > > Any advice would be welcome and appreciated...... > > -Brian > 91 YJ 4.0 > > o_o_o_o > /| ,[_____], > |ŻŻŻL --O|||||||O- > ()_)Ż()_) ŻŻŻ )_) > > > |
Re: *How to for a U Joint.....*
Bill H will likely chime in with a web site that is pretty through on
how to do it. Only problem is that he lives in the southwest where ice, snow, RAIN, and 10,000 salt trucks don't darken his doorstep. If you live north, the hub will be a real stinker to get loose from the steering knuckle. Lot of choices in how to get it out, mine is to jack the front end up HIGH, (use 6 ton jack stands to get it up high enough), use a BFH from directly undneath. YMMV Brian wrote: > Hi, changing a front end u joint the right side. 1st time doing this. Before > i go ahead start this weekend thought I would ask if anyone has a good "How > to" step by step web page or anything else? So I might make quicker,safer > work of this task. Although I have help, I have been told if I do this wrong > the results could be disastrous. :-| > > Any advice would be welcome and appreciated...... > > -Brian > 91 YJ 4.0 > > o_o_o_o > /| ,[_____], > |ŻŻŻL --O|||||||O- > ()_)Ż()_) ŻŻŻ )_) > > > |
Re: *How to for a U Joint.....*
Hi Brian,
Usually you'll find the hub a little rusted in, use penetrating fluid, some like to leave one the bolts in, just back it off enough to persuade it with a BMFH. I use a paint scraper and drive it in-between the knuckle and hub: http://www.madxj.com/MADXJ/technical...97andSeals.htm God Bless America, ßill O|||||||O mailto:-------------------- http://www.----------.com/ Brian wrote: > > Hi, changing a front end u joint the right side. 1st time doing this. Before > i go ahead start this weekend thought I would ask if anyone has a good "How > to" step by step web page or anything else? So I might make quicker,safer > work of this task. Although I have help, I have been told if I do this wrong > the results could be disastrous. :-| > > Any advice would be welcome and appreciated...... > > -Brian > 91 YJ 4.0 > > o_o_o_o > /| ,[_____], > |ŻŻŻL --O|||||||O- > ()_)Ż()_) ŻŻŻ )_) > |
Re: *How to for a U Joint.....*
Hi Brian,
Usually you'll find the hub a little rusted in, use penetrating fluid, some like to leave one the bolts in, just back it off enough to persuade it with a BMFH. I use a paint scraper and drive it in-between the knuckle and hub: http://www.madxj.com/MADXJ/technical...97andSeals.htm God Bless America, ßill O|||||||O mailto:-------------------- http://www.----------.com/ Brian wrote: > > Hi, changing a front end u joint the right side. 1st time doing this. Before > i go ahead start this weekend thought I would ask if anyone has a good "How > to" step by step web page or anything else? So I might make quicker,safer > work of this task. Although I have help, I have been told if I do this wrong > the results could be disastrous. :-| > > Any advice would be welcome and appreciated...... > > -Brian > 91 YJ 4.0 > > o_o_o_o > /| ,[_____], > |ŻŻŻL --O|||||||O- > ()_)Ż()_) ŻŻŻ )_) > |
Re: *How to for a U Joint.....*
Hi Brian,
Usually you'll find the hub a little rusted in, use penetrating fluid, some like to leave one the bolts in, just back it off enough to persuade it with a BMFH. I use a paint scraper and drive it in-between the knuckle and hub: http://www.madxj.com/MADXJ/technical...97andSeals.htm God Bless America, ßill O|||||||O mailto:-------------------- http://www.----------.com/ Brian wrote: > > Hi, changing a front end u joint the right side. 1st time doing this. Before > i go ahead start this weekend thought I would ask if anyone has a good "How > to" step by step web page or anything else? So I might make quicker,safer > work of this task. Although I have help, I have been told if I do this wrong > the results could be disastrous. :-| > > Any advice would be welcome and appreciated...... > > -Brian > 91 YJ 4.0 > > o_o_o_o > /| ,[_____], > |ŻŻŻL --O|||||||O- > ()_)Ż()_) ŻŻŻ )_) > |
Re: *How to for a U Joint.....*
Hi Brian,
Usually you'll find the hub a little rusted in, use penetrating fluid, some like to leave one the bolts in, just back it off enough to persuade it with a BMFH. I use a paint scraper and drive it in-between the knuckle and hub: http://www.madxj.com/MADXJ/technical...97andSeals.htm God Bless America, ßill O|||||||O mailto:-------------------- http://www.----------.com/ Brian wrote: > > Hi, changing a front end u joint the right side. 1st time doing this. Before > i go ahead start this weekend thought I would ask if anyone has a good "How > to" step by step web page or anything else? So I might make quicker,safer > work of this task. Although I have help, I have been told if I do this wrong > the results could be disastrous. :-| > > Any advice would be welcome and appreciated...... > > -Brian > 91 YJ 4.0 > > o_o_o_o > /| ,[_____], > |ŻŻŻL --O|||||||O- > ()_)Ż()_) ŻŻŻ )_) > |
Re: *How to for a U Joint.....*
I JUST did this, had a "took took" sound.
rent a slide hammer, It was a lot of grunting to get the hub out..... "Brian" <urk500@yahoo.com> wrote in message news:wpZ9e.10642$sp3.9592@newsread3.news.atl.earth link.net... > Hi, changing a front end u joint the right side. 1st time doing this. > Before i go ahead start this weekend thought I would ask if anyone has a > good "How to" step by step web page or anything else? So I might make > quicker,safer work of this task. Although I have help, I have been told if > I do this wrong the results could be disastrous. :-| > > Any advice would be welcome and appreciated...... > > -Brian > 91 YJ 4.0 > > o_o_o_o > /| ,[_____], > |ŻŻŻL --O|||||||O- > ()_)Ż()_) ŻŻŻ )_) > > > |
Re: *How to for a U Joint.....*
I JUST did this, had a "took took" sound.
rent a slide hammer, It was a lot of grunting to get the hub out..... "Brian" <urk500@yahoo.com> wrote in message news:wpZ9e.10642$sp3.9592@newsread3.news.atl.earth link.net... > Hi, changing a front end u joint the right side. 1st time doing this. > Before i go ahead start this weekend thought I would ask if anyone has a > good "How to" step by step web page or anything else? So I might make > quicker,safer work of this task. Although I have help, I have been told if > I do this wrong the results could be disastrous. :-| > > Any advice would be welcome and appreciated...... > > -Brian > 91 YJ 4.0 > > o_o_o_o > /| ,[_____], > |ŻŻŻL --O|||||||O- > ()_)Ż()_) ŻŻŻ )_) > > > |
Re: *How to for a U Joint.....*
I JUST did this, had a "took took" sound.
rent a slide hammer, It was a lot of grunting to get the hub out..... "Brian" <urk500@yahoo.com> wrote in message news:wpZ9e.10642$sp3.9592@newsread3.news.atl.earth link.net... > Hi, changing a front end u joint the right side. 1st time doing this. > Before i go ahead start this weekend thought I would ask if anyone has a > good "How to" step by step web page or anything else? So I might make > quicker,safer work of this task. Although I have help, I have been told if > I do this wrong the results could be disastrous. :-| > > Any advice would be welcome and appreciated...... > > -Brian > 91 YJ 4.0 > > o_o_o_o > /| ,[_____], > |ŻŻŻL --O|||||||O- > ()_)Ż()_) ŻŻŻ )_) > > > |
Re: *How to for a U Joint.....*
I JUST did this, had a "took took" sound.
rent a slide hammer, It was a lot of grunting to get the hub out..... "Brian" <urk500@yahoo.com> wrote in message news:wpZ9e.10642$sp3.9592@newsread3.news.atl.earth link.net... > Hi, changing a front end u joint the right side. 1st time doing this. > Before i go ahead start this weekend thought I would ask if anyone has a > good "How to" step by step web page or anything else? So I might make > quicker,safer work of this task. Although I have help, I have been told if > I do this wrong the results could be disastrous. :-| > > Any advice would be welcome and appreciated...... > > -Brian > 91 YJ 4.0 > > o_o_o_o > /| ,[_____], > |ŻŻŻL --O|||||||O- > ()_)Ż()_) ŻŻŻ )_) > > > |
Re: *How to for a U Joint.....*
Wow!
You managed to get the hub out in one piece with a slap hammer!!!???? Crap man, those are sealed hubs and normally pull apart into pieces way before the spindle is going to move. Or can/did you do it leaving the axle nut in place and slap the whole works out? I use a sacrificial bolt and cut the wheels one way then the other so I can hammer it out from behind. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Pi-Eyed Piper wrote: > > I JUST did this, had a "took took" sound. > > rent a slide hammer, It was a lot of grunting to get the hub out..... > > "Brian" <urk500@yahoo.com> wrote in message > news:wpZ9e.10642$sp3.9592@newsread3.news.atl.earth link.net... > > Hi, changing a front end u joint the right side. 1st time doing this. > > Before i go ahead start this weekend thought I would ask if anyone has a > > good "How to" step by step web page or anything else? So I might make > > quicker,safer work of this task. Although I have help, I have been told if > > I do this wrong the results could be disastrous. :-| > > > > Any advice would be welcome and appreciated...... > > > > -Brian > > 91 YJ 4.0 > > > > o_o_o_o > > /| ,[_____], > > |ŻŻŻL --O|||||||O- > > ()_)Ż()_) ŻŻŻ )_) > > > > > > |
Re: *How to for a U Joint.....*
Wow!
You managed to get the hub out in one piece with a slap hammer!!!???? Crap man, those are sealed hubs and normally pull apart into pieces way before the spindle is going to move. Or can/did you do it leaving the axle nut in place and slap the whole works out? I use a sacrificial bolt and cut the wheels one way then the other so I can hammer it out from behind. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Pi-Eyed Piper wrote: > > I JUST did this, had a "took took" sound. > > rent a slide hammer, It was a lot of grunting to get the hub out..... > > "Brian" <urk500@yahoo.com> wrote in message > news:wpZ9e.10642$sp3.9592@newsread3.news.atl.earth link.net... > > Hi, changing a front end u joint the right side. 1st time doing this. > > Before i go ahead start this weekend thought I would ask if anyone has a > > good "How to" step by step web page or anything else? So I might make > > quicker,safer work of this task. Although I have help, I have been told if > > I do this wrong the results could be disastrous. :-| > > > > Any advice would be welcome and appreciated...... > > > > -Brian > > 91 YJ 4.0 > > > > o_o_o_o > > /| ,[_____], > > |ŻŻŻL --O|||||||O- > > ()_)Ż()_) ŻŻŻ )_) > > > > > > |
Re: *How to for a U Joint.....*
Wow!
You managed to get the hub out in one piece with a slap hammer!!!???? Crap man, those are sealed hubs and normally pull apart into pieces way before the spindle is going to move. Or can/did you do it leaving the axle nut in place and slap the whole works out? I use a sacrificial bolt and cut the wheels one way then the other so I can hammer it out from behind. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Pi-Eyed Piper wrote: > > I JUST did this, had a "took took" sound. > > rent a slide hammer, It was a lot of grunting to get the hub out..... > > "Brian" <urk500@yahoo.com> wrote in message > news:wpZ9e.10642$sp3.9592@newsread3.news.atl.earth link.net... > > Hi, changing a front end u joint the right side. 1st time doing this. > > Before i go ahead start this weekend thought I would ask if anyone has a > > good "How to" step by step web page or anything else? So I might make > > quicker,safer work of this task. Although I have help, I have been told if > > I do this wrong the results could be disastrous. :-| > > > > Any advice would be welcome and appreciated...... > > > > -Brian > > 91 YJ 4.0 > > > > o_o_o_o > > /| ,[_____], > > |ŻŻŻL --O|||||||O- > > ()_)Ż()_) ŻŻŻ )_) > > > > > > |
Re: *How to for a U Joint.....*
Wow!
You managed to get the hub out in one piece with a slap hammer!!!???? Crap man, those are sealed hubs and normally pull apart into pieces way before the spindle is going to move. Or can/did you do it leaving the axle nut in place and slap the whole works out? I use a sacrificial bolt and cut the wheels one way then the other so I can hammer it out from behind. Mike 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 88 Cherokee 235 BFG AT's Pi-Eyed Piper wrote: > > I JUST did this, had a "took took" sound. > > rent a slide hammer, It was a lot of grunting to get the hub out..... > > "Brian" <urk500@yahoo.com> wrote in message > news:wpZ9e.10642$sp3.9592@newsread3.news.atl.earth link.net... > > Hi, changing a front end u joint the right side. 1st time doing this. > > Before i go ahead start this weekend thought I would ask if anyone has a > > good "How to" step by step web page or anything else? So I might make > > quicker,safer work of this task. Although I have help, I have been told if > > I do this wrong the results could be disastrous. :-| > > > > Any advice would be welcome and appreciated...... > > > > -Brian > > 91 YJ 4.0 > > > > o_o_o_o > > /| ,[_____], > > |ŻŻŻL --O|||||||O- > > ()_)Ż()_) ŻŻŻ )_) > > > > > > |
Re: *How to for a U Joint.....*
I shouldn't say this....I used an air chissel...got it out far enough I
could use a BFH from the front. I managed to destroy one of the bolt holes in assembly the with the chissel which I had to fix. The guy that changed them last time, whenever that was, managed to bend the yoke enough that it required some force and ignorance to make it work. Wasn't a fun job...im not the best wrencher but I'll try anything. Learned that I don't like changing those u-joints though.... "Mike Romain" <romainm@sympatico.ca> wrote in message news:42692B44.1C06BF0B@sympatico.ca... > Wow! > > You managed to get the hub out in one piece with a slap hammer!!!???? > > Crap man, those are sealed hubs and normally pull apart into pieces way > before the spindle is going to move. > > Or can/did you do it leaving the axle nut in place and slap the whole > works out? > > I use a sacrificial bolt and cut the wheels one way then the other so I > can hammer it out from behind. > > Mike > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > 88 Cherokee 235 BFG AT's > > Pi-Eyed Piper wrote: >> >> I JUST did this, had a "took took" sound. >> >> rent a slide hammer, It was a lot of grunting to get the hub out..... >> >> "Brian" <urk500@yahoo.com> wrote in message >> news:wpZ9e.10642$sp3.9592@newsread3.news.atl.earth link.net... >> > Hi, changing a front end u joint the right side. 1st time doing this. >> > Before i go ahead start this weekend thought I would ask if anyone has >> > a >> > good "How to" step by step web page or anything else? So I might make >> > quicker,safer work of this task. Although I have help, I have been told >> > if >> > I do this wrong the results could be disastrous. :-| >> > >> > Any advice would be welcome and appreciated...... >> > >> > -Brian >> > 91 YJ 4.0 >> > >> > o_o_o_o >> > /| ,[_____], >> > |ŻŻŻL --O|||||||O- >> > ()_)Ż()_) ŻŻŻ )_) >> > >> > >> > |
Re: *How to for a U Joint.....*
I shouldn't say this....I used an air chissel...got it out far enough I
could use a BFH from the front. I managed to destroy one of the bolt holes in assembly the with the chissel which I had to fix. The guy that changed them last time, whenever that was, managed to bend the yoke enough that it required some force and ignorance to make it work. Wasn't a fun job...im not the best wrencher but I'll try anything. Learned that I don't like changing those u-joints though.... "Mike Romain" <romainm@sympatico.ca> wrote in message news:42692B44.1C06BF0B@sympatico.ca... > Wow! > > You managed to get the hub out in one piece with a slap hammer!!!???? > > Crap man, those are sealed hubs and normally pull apart into pieces way > before the spindle is going to move. > > Or can/did you do it leaving the axle nut in place and slap the whole > works out? > > I use a sacrificial bolt and cut the wheels one way then the other so I > can hammer it out from behind. > > Mike > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > 88 Cherokee 235 BFG AT's > > Pi-Eyed Piper wrote: >> >> I JUST did this, had a "took took" sound. >> >> rent a slide hammer, It was a lot of grunting to get the hub out..... >> >> "Brian" <urk500@yahoo.com> wrote in message >> news:wpZ9e.10642$sp3.9592@newsread3.news.atl.earth link.net... >> > Hi, changing a front end u joint the right side. 1st time doing this. >> > Before i go ahead start this weekend thought I would ask if anyone has >> > a >> > good "How to" step by step web page or anything else? So I might make >> > quicker,safer work of this task. Although I have help, I have been told >> > if >> > I do this wrong the results could be disastrous. :-| >> > >> > Any advice would be welcome and appreciated...... >> > >> > -Brian >> > 91 YJ 4.0 >> > >> > o_o_o_o >> > /| ,[_____], >> > |ŻŻŻL --O|||||||O- >> > ()_)Ż()_) ŻŻŻ )_) >> > >> > >> > |
Re: *How to for a U Joint.....*
I shouldn't say this....I used an air chissel...got it out far enough I
could use a BFH from the front. I managed to destroy one of the bolt holes in assembly the with the chissel which I had to fix. The guy that changed them last time, whenever that was, managed to bend the yoke enough that it required some force and ignorance to make it work. Wasn't a fun job...im not the best wrencher but I'll try anything. Learned that I don't like changing those u-joints though.... "Mike Romain" <romainm@sympatico.ca> wrote in message news:42692B44.1C06BF0B@sympatico.ca... > Wow! > > You managed to get the hub out in one piece with a slap hammer!!!???? > > Crap man, those are sealed hubs and normally pull apart into pieces way > before the spindle is going to move. > > Or can/did you do it leaving the axle nut in place and slap the whole > works out? > > I use a sacrificial bolt and cut the wheels one way then the other so I > can hammer it out from behind. > > Mike > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > 88 Cherokee 235 BFG AT's > > Pi-Eyed Piper wrote: >> >> I JUST did this, had a "took took" sound. >> >> rent a slide hammer, It was a lot of grunting to get the hub out..... >> >> "Brian" <urk500@yahoo.com> wrote in message >> news:wpZ9e.10642$sp3.9592@newsread3.news.atl.earth link.net... >> > Hi, changing a front end u joint the right side. 1st time doing this. >> > Before i go ahead start this weekend thought I would ask if anyone has >> > a >> > good "How to" step by step web page or anything else? So I might make >> > quicker,safer work of this task. Although I have help, I have been told >> > if >> > I do this wrong the results could be disastrous. :-| >> > >> > Any advice would be welcome and appreciated...... >> > >> > -Brian >> > 91 YJ 4.0 >> > >> > o_o_o_o >> > /| ,[_____], >> > |ŻŻŻL --O|||||||O- >> > ()_)Ż()_) ŻŻŻ )_) >> > >> > >> > |
Re: *How to for a U Joint.....*
I shouldn't say this....I used an air chissel...got it out far enough I
could use a BFH from the front. I managed to destroy one of the bolt holes in assembly the with the chissel which I had to fix. The guy that changed them last time, whenever that was, managed to bend the yoke enough that it required some force and ignorance to make it work. Wasn't a fun job...im not the best wrencher but I'll try anything. Learned that I don't like changing those u-joints though.... "Mike Romain" <romainm@sympatico.ca> wrote in message news:42692B44.1C06BF0B@sympatico.ca... > Wow! > > You managed to get the hub out in one piece with a slap hammer!!!???? > > Crap man, those are sealed hubs and normally pull apart into pieces way > before the spindle is going to move. > > Or can/did you do it leaving the axle nut in place and slap the whole > works out? > > I use a sacrificial bolt and cut the wheels one way then the other so I > can hammer it out from behind. > > Mike > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > 88 Cherokee 235 BFG AT's > > Pi-Eyed Piper wrote: >> >> I JUST did this, had a "took took" sound. >> >> rent a slide hammer, It was a lot of grunting to get the hub out..... >> >> "Brian" <urk500@yahoo.com> wrote in message >> news:wpZ9e.10642$sp3.9592@newsread3.news.atl.earth link.net... >> > Hi, changing a front end u joint the right side. 1st time doing this. >> > Before i go ahead start this weekend thought I would ask if anyone has >> > a >> > good "How to" step by step web page or anything else? So I might make >> > quicker,safer work of this task. Although I have help, I have been told >> > if >> > I do this wrong the results could be disastrous. :-| >> > >> > Any advice would be welcome and appreciated...... >> > >> > -Brian >> > 91 YJ 4.0 >> > >> > o_o_o_o >> > /| ,[_____], >> > |ŻŻŻL --O|||||||O- >> > ()_)Ż()_) ŻŻŻ )_) >> > >> > >> > |
Re: *How to for a U Joint.....*
Harbor Freight sells a U-Joint tool kit, sure is easier that using a 3/4"
deep socket and a BFH. http://www.harborfreight.com/cpi/cta...emnumber=38335 They go on sale now and they for $19.99, good for the shop and for trail repairs. Also here is a link to a little better quality tool. http://rockcrawler.com/techreports/ujointtool/index.asp "Brian" <urk500@yahoo.com> wrote in message news:wpZ9e.10642$sp3.9592@newsread3.news.atl.earth link.net... > Hi, changing a front end u joint the right side. 1st time doing this. > Before i go ahead start this weekend thought I would ask if anyone has a > good "How to" step by step web page or anything else? So I might make > quicker,safer work of this task. Although I have help, I have been told if > I do this wrong the results could be disastrous. :-| > > Any advice would be welcome and appreciated...... > > -Brian > 91 YJ 4.0 > > o_o_o_o > /| ,[_____], > |ŻŻŻL --O|||||||O- > ()_)Ż()_) ŻŻŻ )_) > > > |
Re: *How to for a U Joint.....*
Harbor Freight sells a U-Joint tool kit, sure is easier that using a 3/4"
deep socket and a BFH. http://www.harborfreight.com/cpi/cta...emnumber=38335 They go on sale now and they for $19.99, good for the shop and for trail repairs. Also here is a link to a little better quality tool. http://rockcrawler.com/techreports/ujointtool/index.asp "Brian" <urk500@yahoo.com> wrote in message news:wpZ9e.10642$sp3.9592@newsread3.news.atl.earth link.net... > Hi, changing a front end u joint the right side. 1st time doing this. > Before i go ahead start this weekend thought I would ask if anyone has a > good "How to" step by step web page or anything else? So I might make > quicker,safer work of this task. Although I have help, I have been told if > I do this wrong the results could be disastrous. :-| > > Any advice would be welcome and appreciated...... > > -Brian > 91 YJ 4.0 > > o_o_o_o > /| ,[_____], > |ŻŻŻL --O|||||||O- > ()_)Ż()_) ŻŻŻ )_) > > > |
Re: *How to for a U Joint.....*
Harbor Freight sells a U-Joint tool kit, sure is easier that using a 3/4"
deep socket and a BFH. http://www.harborfreight.com/cpi/cta...emnumber=38335 They go on sale now and they for $19.99, good for the shop and for trail repairs. Also here is a link to a little better quality tool. http://rockcrawler.com/techreports/ujointtool/index.asp "Brian" <urk500@yahoo.com> wrote in message news:wpZ9e.10642$sp3.9592@newsread3.news.atl.earth link.net... > Hi, changing a front end u joint the right side. 1st time doing this. > Before i go ahead start this weekend thought I would ask if anyone has a > good "How to" step by step web page or anything else? So I might make > quicker,safer work of this task. Although I have help, I have been told if > I do this wrong the results could be disastrous. :-| > > Any advice would be welcome and appreciated...... > > -Brian > 91 YJ 4.0 > > o_o_o_o > /| ,[_____], > |ŻŻŻL --O|||||||O- > ()_)Ż()_) ŻŻŻ )_) > > > |
Re: *How to for a U Joint.....*
Harbor Freight sells a U-Joint tool kit, sure is easier that using a 3/4"
deep socket and a BFH. http://www.harborfreight.com/cpi/cta...emnumber=38335 They go on sale now and they for $19.99, good for the shop and for trail repairs. Also here is a link to a little better quality tool. http://rockcrawler.com/techreports/ujointtool/index.asp "Brian" <urk500@yahoo.com> wrote in message news:wpZ9e.10642$sp3.9592@newsread3.news.atl.earth link.net... > Hi, changing a front end u joint the right side. 1st time doing this. > Before i go ahead start this weekend thought I would ask if anyone has a > good "How to" step by step web page or anything else? So I might make > quicker,safer work of this task. Although I have help, I have been told if > I do this wrong the results could be disastrous. :-| > > Any advice would be welcome and appreciated...... > > -Brian > 91 YJ 4.0 > > o_o_o_o > /| ,[_____], > |ŻŻŻL --O|||||||O- > ()_)Ż()_) ŻŻŻ )_) > > > |
Re: *How to for a U Joint.....*
Looks like the ujointtool guy is out of business - seemed a neat tool too
Dave Milne, Scotland '91 Grand Wagoneer, '99 TJ "Rusted" <noEmail@please.com> wrote in message news:xLaae.20092$ig1.18303@fe37.usenetserver.com.. . Also here is a link to a little better quality tool. > > http://rockcrawler.com/techreports/ujointtool/index.asp |
Re: *How to for a U Joint.....*
Looks like the ujointtool guy is out of business - seemed a neat tool too
Dave Milne, Scotland '91 Grand Wagoneer, '99 TJ "Rusted" <noEmail@please.com> wrote in message news:xLaae.20092$ig1.18303@fe37.usenetserver.com.. . Also here is a link to a little better quality tool. > > http://rockcrawler.com/techreports/ujointtool/index.asp |
Re: *How to for a U Joint.....*
Looks like the ujointtool guy is out of business - seemed a neat tool too
Dave Milne, Scotland '91 Grand Wagoneer, '99 TJ "Rusted" <noEmail@please.com> wrote in message news:xLaae.20092$ig1.18303@fe37.usenetserver.com.. . Also here is a link to a little better quality tool. > > http://rockcrawler.com/techreports/ujointtool/index.asp |
Re: *How to for a U Joint.....*
Looks like the ujointtool guy is out of business - seemed a neat tool too
Dave Milne, Scotland '91 Grand Wagoneer, '99 TJ "Rusted" <noEmail@please.com> wrote in message news:xLaae.20092$ig1.18303@fe37.usenetserver.com.. . Also here is a link to a little better quality tool. > > http://rockcrawler.com/techreports/ujointtool/index.asp |
Re: *How to for a U Joint.....*
Ditto.
God Bless America, ßill O|||||||O mailto:-------------------- http://www.----------.com/ Mike Romain wrote: > > Wow! > > You managed to get the hub out in one piece with a slap hammer!!!???? > > Crap man, those are sealed hubs and normally pull apart into pieces way > before the spindle is going to move. > > Or can/did you do it leaving the axle nut in place and slap the whole > works out? > > I use a sacrificial bolt and cut the wheels one way then the other so I > can hammer it out from behind. > > Mike > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > 88 Cherokee 235 BFG AT's |
Re: *How to for a U Joint.....*
Ditto.
God Bless America, ßill O|||||||O mailto:-------------------- http://www.----------.com/ Mike Romain wrote: > > Wow! > > You managed to get the hub out in one piece with a slap hammer!!!???? > > Crap man, those are sealed hubs and normally pull apart into pieces way > before the spindle is going to move. > > Or can/did you do it leaving the axle nut in place and slap the whole > works out? > > I use a sacrificial bolt and cut the wheels one way then the other so I > can hammer it out from behind. > > Mike > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > 88 Cherokee 235 BFG AT's |
Re: *How to for a U Joint.....*
Ditto.
God Bless America, ßill O|||||||O mailto:-------------------- http://www.----------.com/ Mike Romain wrote: > > Wow! > > You managed to get the hub out in one piece with a slap hammer!!!???? > > Crap man, those are sealed hubs and normally pull apart into pieces way > before the spindle is going to move. > > Or can/did you do it leaving the axle nut in place and slap the whole > works out? > > I use a sacrificial bolt and cut the wheels one way then the other so I > can hammer it out from behind. > > Mike > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > 88 Cherokee 235 BFG AT's |
Re: *How to for a U Joint.....*
Ditto.
God Bless America, ßill O|||||||O mailto:-------------------- http://www.----------.com/ Mike Romain wrote: > > Wow! > > You managed to get the hub out in one piece with a slap hammer!!!???? > > Crap man, those are sealed hubs and normally pull apart into pieces way > before the spindle is going to move. > > Or can/did you do it leaving the axle nut in place and slap the whole > works out? > > I use a sacrificial bolt and cut the wheels one way then the other so I > can hammer it out from behind. > > Mike > 86/00 CJ7 Laredo, 33x9.5 BFG Muds, 'glass nose to tail in '00 > 88 Cherokee 235 BFG AT's |
Re: *How to for a U Joint.....*
Thank you all :-) Fantastic info. I will be doing this 4/30-31 and will post
what happens. Glad i have a motorcycle esp with gas prices... o_o_o_o /| ,[_____], |ŻŻŻL --O|||||||O- ()_)Ż()_) ŻŻŻ )_) "Brian" <urk500@yahoo.com> wrote in message news:wpZ9e.10642$sp3.9592@newsread3.news.atl.earth link.net... > Hi, changing a front end u joint the right side. 1st time doing this. > Before i go ahead start this weekend thought I would ask if anyone has a > good "How to" step by step web page or anything else? So I might make > quicker,safer work of this task. Although I have help, I have been told if > I do this wrong the results could be disastrous. :-| > > Any advice would be welcome and appreciated...... > > -Brian > 91 YJ 4.0 > > o_o_o_o > /| ,[_____], > |ŻŻŻL --O|||||||O- > ()_)Ż()_) ŻŻŻ )_) > > > |
Re: *How to for a U Joint.....*
Thank you all :-) Fantastic info. I will be doing this 4/30-31 and will post
what happens. Glad i have a motorcycle esp with gas prices... o_o_o_o /| ,[_____], |ŻŻŻL --O|||||||O- ()_)Ż()_) ŻŻŻ )_) "Brian" <urk500@yahoo.com> wrote in message news:wpZ9e.10642$sp3.9592@newsread3.news.atl.earth link.net... > Hi, changing a front end u joint the right side. 1st time doing this. > Before i go ahead start this weekend thought I would ask if anyone has a > good "How to" step by step web page or anything else? So I might make > quicker,safer work of this task. Although I have help, I have been told if > I do this wrong the results could be disastrous. :-| > > Any advice would be welcome and appreciated...... > > -Brian > 91 YJ 4.0 > > o_o_o_o > /| ,[_____], > |ŻŻŻL --O|||||||O- > ()_)Ż()_) ŻŻŻ )_) > > > |
Re: *How to for a U Joint.....*
Thank you all :-) Fantastic info. I will be doing this 4/30-31 and will post
what happens. Glad i have a motorcycle esp with gas prices... o_o_o_o /| ,[_____], |ŻŻŻL --O|||||||O- ()_)Ż()_) ŻŻŻ )_) "Brian" <urk500@yahoo.com> wrote in message news:wpZ9e.10642$sp3.9592@newsread3.news.atl.earth link.net... > Hi, changing a front end u joint the right side. 1st time doing this. > Before i go ahead start this weekend thought I would ask if anyone has a > good "How to" step by step web page or anything else? So I might make > quicker,safer work of this task. Although I have help, I have been told if > I do this wrong the results could be disastrous. :-| > > Any advice would be welcome and appreciated...... > > -Brian > 91 YJ 4.0 > > o_o_o_o > /| ,[_____], > |ŻŻŻL --O|||||||O- > ()_)Ż()_) ŻŻŻ )_) > > > |
Re: *How to for a U Joint.....*
Thank you all :-) Fantastic info. I will be doing this 4/30-31 and will post
what happens. Glad i have a motorcycle esp with gas prices... o_o_o_o /| ,[_____], |ŻŻŻL --O|||||||O- ()_)Ż()_) ŻŻŻ )_) "Brian" <urk500@yahoo.com> wrote in message news:wpZ9e.10642$sp3.9592@newsread3.news.atl.earth link.net... > Hi, changing a front end u joint the right side. 1st time doing this. > Before i go ahead start this weekend thought I would ask if anyone has a > good "How to" step by step web page or anything else? So I might make > quicker,safer work of this task. Although I have help, I have been told if > I do this wrong the results could be disastrous. :-| > > Any advice would be welcome and appreciated...... > > -Brian > 91 YJ 4.0 > > o_o_o_o > /| ,[_____], > |ŻŻŻL --O|||||||O- > ()_)Ż()_) ŻŻŻ )_) > > > |
All times are GMT -4. The time now is 02:25 AM. |
© 2024 MH Sub I, LLC dba Internet Brands